SW-MOTECH BC.HTA.05.740.31000 Blaze Saddlebags Support Arms Instruction Manual
- June 16, 2024
- SW-MOTECH
Table of Contents
mounting instructions
BC.HTA.05.740.31000
contains
HTA.05.740.81000/B
BC.HTA.00.740.31000
MOUNTING INSTRUCTIONS
READ AND SAVE THESE MOUNTING INSTRUCTIONS
tem No.: HTA.05.740.81000/B
Revision: 00 · Date: 09 – 2022
BLAZE® saddlebags support arms for BLAZE® saddlebags high version
Thank you for choosing this premium product from SW-MOTECH. Please carefully
read and understand all instructions, safety messages and warnings in this
mounting instructions prior to installation and use of this product to avoid
injury.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Visit our webshop for additional information, such as
application charts and PDF mounting instructions. Any other documents that may
be required (e.g. ABE certifications), are also available for download at our
webshop. Keep these mounting instructions as reference.
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
SAFETY ALERT SYMBOL
This safety alert symbol is used throughout these mounting instructions to
warn of the possibility of death, bodily injury or other warnings. The words
DANGER, WARNING and CAUTION are used with this safety alert symbol to convey
important safety messages and information related to the installation and use
of this product. These words along with the safety alert symbol mean:
DANGER: Indicates a hazardous situation that, if not avoided, will result
in death or serious injury!
WARNING: Indicates a hazardous situation that, fnot avoided, could result
in death or serious injury!
CAUTION: Indicates a hazardous situation that, fnot avoided, could result
in minor or moderate injury!
NOTICE: Important information, but not death or injury related (property
damage only)!
WARNING: The installation and/or maintenance of this product requires
advanced mechanical skills, the proper tools, and a thorough understanding of
tool use and torque specifications.
For your own safety, SW-MOTECH recommends having installation and/or
maintenance carried out by a qualified and certified motorcycle mechanic.
WARNING: Should you choose to self-install this product, carefully and
completely read all intallation and safety instructions before installation
and use, and follow all the directions and safety precautions given in the
mounting instructions to avoid serious injury or death. Also pay attention to
all relevant information in the vehicle manual during intallation and use.
IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS, OR NEED CLARIFICATION
OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS PRODUCT WITHOUT CONTACTING SW-
MOTECH FOR ASSISTANCE.
PREPARATION: Read the mounting nstructions carefully and make sure that
all items of the parts list are included.
CAUTION: Make sure that your vehicle is parked safely and cannot fall
over. Turn off the engine and remove the ignition key. Let the engine/exhaust
cool off if necessary. Disconnect the vehicle battery when working on the
electrical system. Use appropriate tools and wear always safety glasses and
hand protection. Have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled n accordance with the vehicle manufacturer specifications or
replaced by parts and hardware delivered by SW-MOTECH.
WARNING: Secure all threads, unless otherwise specified, with medium
strong strength liquid thread locker. Torque specifications undefined by SW-
MOTECH must be obtained from the vehicle manufacturer or by a certified
motorcycle workshop!
FUNCTION CHECK: After installation also make sure that no moving parts
are obstructed, and function of the vehicle is not hindered in any way. Cables
and hoses must not rub and/or be pinched.
WARNING: Before starting to ride, perform a comprehensive check of all
functions. After the first 50 km and then at regular intervals, check the
tightening torque of all connections and the proper fit of the product.
Installed accessories can change driving behavior/stability of the vehicle.
SW-MOTECH GmbH &
Co. KG
Ernteweg 7-10
35282 Rauschenberg
Germany
Tel. / phone+ 49 (0]6425 / 8168 – 050
Fax / fax+ 49 (0]6425 / 8168 – 10
inforasw-motech.com
www.sw-motech.com
PARTS LIST
READ AND SAVE THESE MOUNTING INSTRUCTIONS
Schrift
Step| Nr.
No.| Item No. / Description a| Part| Anzaht b
Quantity b| N•mc
---|---|---|---|---|---
1| (1)| HTA.08.740.015L / R| Mounting Bracket; left / right| 2 /2|
| (2)| HTA.00.740.010| Connector Holder| 2 /2|
(3)| M5 x 16; DIN 6912| Hexagon Socket Screw, short head; black| 6 /6| 2,5
(4)| M5 x 20; DIN 6912| Hexagon Socket Screw, short head; black| 2 /2| 2,5
(5)| Ø 5,3; DIN 9021| Washer| 2 /2|
(6)| M5; DIN 6927| Lock Nut with Flange| 8 /8|
| | | |
2| (7)| HTA.04.740.004L / R| Support Arms; left / right| 2 /2|
| (8)| KES_RD.1 50_0200.02_GL| Plastic Plug| 2/2|
(9)| HTA.00.740.01 1 L / R| Connector; left / right| 2 /2|
(10)| M5 x 12; DIN 912| Hexagon Socket Screw; black| 4/4| 1,2
(11)| M5; DIN 985| Lock Nut| 4/4|
| | | |
4| (12)| M8 x 85; DIN 912| Hexaon Socket Screw| 4 /4| 23
| (13)| 0 8,4; DIN 125| Washer| 4/4|
(14)| 0 20 / 0 8,4 / h 43| Spacer| 4 /4|
8.8| winde / Coarse Ø| M4| M5| M6| M8| M10| M12
---|---|---|---|---|---|---|---
Steel CL8.8 N•m| 2,8| 5,5| 9,6| 23| 46| 79
10.9| winde / Coarse Ø| M4| M5| M6| M8| M10| M12
---|---|---|---|---|---|---|---
Steel CL8.8 N•m| 4,1| 8,1| 14| 34| 67| 115
Note:a All messurements i mllmeters. The second number mdicates e ttal quantiy
o th part i the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer!
The standard torque in this table can be used 35 long a5 13 within the vehicle
manufacturer s specications. 
MOUNTING
READ AND SAVE THESE MOUNTING INSTRUCTIONS
WARNING: Always wear eye and hand protection!
WARNING: Always use the appropriate tools!
Attach the shown parts to the mounting brackets [1] Left side mounting bracket
shown].
CAUTION: At first just tighten the screws (3) as specified!
Over-tightening the screws will damage the plastic parts!
The shown buckles will come with your saddlebags. Attach them as shown.
CAUTION: Tighten the screws (4) after attaching the saddlebags! 
Attach the
support arms [7] to the connectors [9].
CAUTION: Connect the “L” connector (9) to the “L” support arm (7); Then
connect the components marked with “R”! Also make sure the engraving of the
support arms (7) is aligned downwards as shown in the detail drawing!
CAUTION: Tighten the screws (10) as specified! Over-tightening the screws
will damage the plastic parts!
WARNING: Make sure the support arms (7) fit properly after tightening the
screws (1 OJ! 
Loosen on both
sides the original screws of the passenger footrest mounts and remove them
from the vehicle. 
Attach the
mounting brackets [1 I with the passenger footrest mounts on both sides to the
vehicle.
WARNING: Use liquid thread locker!
Tighten the screws as specified. 
Insert the connectors [9] into the connector-holders
[2] on both sides of the vehicle.
CAUTION: Pay attention to the audible clicking sound!
WARNING: Before mounting the saddlebags to the support arms, pay attention
to the mounting instructions included to the saddlebags!
AFTER mounting the saddlebags, tighten the screws [4] on both sides of the
vehicle as specified.
WARNING: Before riding check the proper fit of the support arms. Remove
the support arms when driving WITHOUT saddlebags from the vehicle!
PRODUCT SPECIFIC INFORMATION
WARNING: Pay attention to the mounting instructions included to the
saddlebags!
NOTICE: Observe the country-specific regulations concerning vehicle
registration/operation as well as TUY regulations if applicable. If required,
register installed parts n the vehicle documents through an appropriate
inspection authority.
MOUNTING INSTRUCTIONS
Item No.: BC.HTA.00.740.3000 & BC.HTA.00.740.3100
Revision: 00 · Date: 09 – 2020
PRO BLAZE® saddlebags
PRO BLAZE® saddlebags high version
Thank you for choosing this premium product from SW-MOTECH. Please visit
our webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behaviour and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations f applicable. If required, register
installed parts in the vehicle documents through an appropriate nspection
authority.
PREPARATION: Read the mounting nstructions carefully and make sure that
all tems of the parts list are included. Make sure that your vehicle is parked
safely and cannot fall over. Turn off the engine and remove the ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
FUNCTION CHECK: After fixation also make sure that no moving parts are
obstructed and the function of the vehicle is not hindered n any way. Lamps as
taillight and turn signals must not be limited in their function. Cables and
hoses must not rub and/or be pinched. Before starting to ride, perform a
comprehensive check of all functions.
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
ATTENTION: Compatibility with accessory exhaust systems cannot be
guaranteed!
All components of the product must not contact any hot or moving parts of the
vehicle. All parts should also remain 5 cm away from hot parts of the vehicle
and remain clear of the exhaust stream. For this reason compress the
suspension fully several times with your vehicle stationary.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving
and braking performance! Cornering and ground clearance can be reduced by
using this product!
ATTENTION: Modifications will void any warranty.
| Maximum Load | Maximum Speed |
|---|---|
| 5 KG (11 tbs) | 130 km/h (80 mph) |
ATTENTION: The maximum vehicle load specified by the manufacturer must
not be exceeded!
ATTENTION
NOT FOR OFFROAD-USE! SW-MOTECH GmbH &
Co. KG
Ernteweg 7-10
35282 Rauschenberg
Germany
Tel./phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (006425 /8168 – 10
info@sw-motech.com
www.sw-motech.com
PARTS LIST
Step| No.| Item No/Description| Part| Quanttity| N.mc
| | BC.HTA.00.740.3000| PRO BLAZE® Saddlebags| |
1| (1)| BC.ZUB.00.019.30000| Buckle| 2/2|
| (2)| LSF.350.250| Protection Foil; 250 x 350 mm| 2/2|
2| (3)| BC.HTA.00.740.901.01 /902.01| Saddlebag; left / right| 2/2|
3| (4)| BC.ZUB.00.064.30000| Waterproof Innerbag| 2/2|
| | BC.HTA.00.740.3100| PRO BLAZE® Saddlebags high version| |
1| (1)| BC.ZUB.00.019.30000| Buckle| 2/2|
| (2)| LSF.350.250| Protection Foil; 250 x 350 mm| 2/2|
2| (3)| BC.HTA.00.740.901.02/ 902.02| Saddlebag; left / right| 2/2|
3| (4)| BC.ZUB.00.064.30000| Waterproof Innerbag| 2/2|
10.9
Regelgewinde / Coarse Thread Ø| M4 | M5 | Mé | M8 |[M10|M12
Stahl FK10.9 / Steel CL10.9 N-m | 4,1 | 8,1 | 14 | 34 | 67 | 115
Note; a All measurements in mllmeters. b The second number ndicates he
tofal quantfy o (e part 1 the deivery. cNo torque specifications: Use the
torque defined by vehicle manufacturer The standard torque in hi table can be
used 35 long a5 13 within the vehicle manufacturer s specications.
FASTENING
After mounting the saddlebags frames you need to protect the surface of the
motorcycle against scratches with the included protection foil (2).
Clean the surface from grease and dirt before applying the protection film
ATTENTION: Sharp edges have to be covered with several layers of the
protection foi After mounting the saddle bags, check if the affected parts of
the vehicle are sufficiently protected against abrasion. 
Slide the
pannier sleeves of the saddlebags (3] on both sides onto the mounted support
arms. 
Fasten the saddlebags (3) with the velcro flaps over the rear (passenger seat)
of the motorcycle, as shown in the drawing
ATTENTION: Make sure after loading the saddlebags (3) there is NO weight
on the saddlebags frames!
The weight of the saddlebags (3) must be supported by the velcro flaps, NEVER
by the saddlebags frames.
After loading, the saddlebags frames must be positioned in the saddlebags
sleeves, as shown in the detail drawing! 
ATTENTION: Pay attention to the mounting
instructions included to the saddlebags support arms! Fix the saddlebags (3)
with the safety straps to the loosely mounted buckles (1] on both sides. Then
tighten the screws of the buckles (1) as described in the mounting
instructions of the saddlebags support arms
Tighten the safety straps to secure the saddlebags
(3] ATTENTION: Make sure BEFORE each ride that the velcro flaps and safety
straps of the saddlebags (3) are firmly tightened and there is NO weight on
the support arms! Wrong mounted saddlebags (3) can damaged the product and
vehicle!
Finally roll up the excess safty strap length and secure it
Use the
waterproof inner bags (4] to protect your luggage from moisture. Additionally
protect sensitive luggage [e.g., electronic equipment] from moisture with a
plastic bag.
SAFETY, LOADING AND CARE
SAFETY AND LOADING: Make sure weight is evenly distributed between the
sagglebags. Make sure that the loanding is secured against shifting during the
ride! Do not store sharp or fragile objects!
ONLY loop assigned SW-MOTECH products to the MOLLE attachment!
ATTENTION: Remove the support arms when driving WITHOUT saddlebags from
the vehicle!
All components of the product must not contact any hot or moving parts of the
vehicle. All parts should also remain 5 cm away from hot parts of the vehicle
and remain clear of the exhaust stream.
ATTENTION: Compatibility with accessory exhaust systems cannot be
guaranteed!
CARE: For
cleaning use ONLY a soft textile brush, cloth or sponge and warm soapy water!
Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure
washer!
Clean the product after riding in salty conditions, to avoid damage from salt.
Copyrgnt oy
SW-MATECH GmbH & Co. KG
Errors and omissions expected. Technical and
design-modificatons are subjects to change