DYNOJET 2011-2013 Husqvarna 449 Models Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for PC6-23005
Model Coverage: 2011-2013 Husqvarna 449 Models
PARTS LIST
| 1 POWER COMMANDER 6 | 2 POWER COMMANDER DECALS |
|---|---|
| 1 INSTALLATION GUIDE | 2 VELCRO STRIPS |
| 1 USB CABLE | 1 ALCOHOL SWAB |
| 2 DYNOJET DECALS | 2 POSI-TAPS |
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two base maps when you hook up a switch
to the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert
the wires from the Dynojet quick shifter into either Input 1 or Input 2. The
polarity of the wires is not important. Set to Input 2 by default.
Speed| If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
set up you can alter your map based on gear position and setup gear-dependent
kill times when using a quick shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your fuel curve based on this input in
the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of the
unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the seat and the plastic panel on the left-hand side of the bike.
-
Route the PC6 harness from the left side of the bike and go towards the throttle body.
-
Unplug the stock wiring harness from the fuel injector.
-
Plug the PC6 connectors in line with the fuel injector and the stock wiring harness.
-
Locate the stock Throttle Position Sensor on the right side of the throttle body and unplug the wiring harness from the TPS.
Feed the PC6 wiring harness branch with the TPS connectors through behind the throttle body to the right-hand side of the bike. -
Plug the PC6 harness in line with the stock wiring harness and the TPS.
-
Use the 2 supplied Positaps to attach the crank input wires of the PC6 to the stock crank position sensor wires. The stock CPS connectors can be found near the left side of the throttle body. The PC6 WHITE/BROWN wire goes to the stock GREEN wire. The PC6 BROWN/WHITE wire goes to the stock BLUE wire.
-
Unplug the stock wiring harness from the ignition coil.
-
Plug the PC6 harness in line with the ignition coil and the stock wiring harness.
-
Attach the ground wire of the PC6 to the negative side of the battery.
-
Using the supplied Velcro, attach the PC6 module to the inside of the left-side plastic body panel. Clean both surfaces with the supplied alcohol swab before attaching the Velcro.
-
Reinstall the seat.
12v source for Auto-tune – BROWN/BLACK wire of BLACK 6-pin diagnostic connector in front of the ECM.
Download the latest map files from our website at dynojet.com/tunes.
PC6-23005
IPC6-23005.01
2011-2013 HUSQVARNA 449 MODELS
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
800-992-4993
DYNOJET.COM
© 2011-2021 DYNOJET RESEARCH
ALL RIGHTS RESERVED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>