LINOVISION IOT-R41 Mini Industrial 4G LTE Router User Manual

Table of Contents

Specifications

CPU : ARM Cortex-A7, 528 MHz
Memory : 128 MB DDR3 RAM and 128 MB Flash
Cellular Interface:
- Network Antenna Connector
- SIM Slot
Ethernet Interface:
- Numbers
- Mode
GNSS Antenna Connector
Serial Interface:
- Number
- Connector
- Terminal Resistor
- Baud Rate
DI/DO:
- Numbers
- Connector
- Maximum V/A (3.5mm Terminal Block)
Others :
- Reset Button
- USB
- LED Indicators
Software:
- Network Protocols
- VPN
- Security
- Management
Power Supply and Consumption:
- Power Connector (2-pin 3.5 mm Terminal Block)
- Power Input
- Power Consumption
Physical Characteristics:
- Ingress Protection
- Housing & Color
- Weight
- Dimension
- Installation
Environmental :
- Operating Temperature
- Storage Temperature
- Ethernet Isolation
- Relative Humidity

Initial Setup

To set up the IOT-R41 Mini Industrial 4G LTE Router, follow these steps:

Connect the cellular network antenna to the appropriate connector.
Insert the SIM card into the SIM slot.
Connect the Ethernet cable to the Ethernet interface.
If required, connect the GNSS antenna to the GNSS antenna connector.
If needed, connect devices to the serial interface using the specified connector and configure the terminal resistor and baud rate.
If necessary, connect devices to the DI/DO interface using the specified connector and configure the maximum voltage/current.
Make sure the power supply is connected to the power connector.
Power on the IOT-R41 by following the power input specifications.

Software Configuration

To configure the software settings of the IOT-R41 Mini Industrial 4G LTE Router, follow these steps:

Access the router’s management interface through web, CLI, SMS, or other supported methods.
Configure the network protocols, VPN settings, security features, and management options according to your requirements.
Set up AAA multilevel authority for user authentication.
Configure the serial port settings if needed for transparent communication or Modbus protocols.

Power Supply and Consumption

The IOT-R41 Mini Industrial 4G LTE Router requires a power supply with the following specifications:

Power Connector : 2-pin 3.5 mm Terminal Block
Power Input: 5-24 VDC, with Surge-Protection and Reverse
Polarity Protection
Power Consumption:
- Idle : 78mA@12V
- Data link : 226mA (peak)@12V
- Standby mode : 6.3 mA@12V

FAQ

Q1. What network protocols does the IOT-R41 support?
The IOT-R41 supports IPv4/IPv6, PPP, PPPoE, SNMP v1/v2c/v3, TCP, UDP, DHCP, RIPv1/v2, OSPF, DDNS, VRRP, HTTP, HTTPS, DNS, ARP, QOS, SNTP, Telnet, and SSH.
Q2. What VPN protocols are supported by the IOT-R41?
The IOT-R41 supports DMVPN, IPsec, OpenVPN, PPTP, L2TP, and GRE.
Q3. What security features does the IOT-R41 have?
The IOT-R41 has SPI Firewalls, Access Control (ACL), DMZ, Port Mapping, MAC Binding, DoS&DDoS Protection, and Filtering (IP&Domain).
Q4. How can I manage the IOT-R41?
You can manage the IOT-R41 through web, CLI, SMS, On-demand dial-up, SNMP v1/v2/v3, DeviceHub, VPN Radius, Tacacs+, LDAP, or Local Authentication.
Q5. What are the physical characteristics of the IOT-R41?
The IOT-R41 has an IP30 metal housing in black color. It weig 103g and has dimensions of 70 x 55 x 22 mm (2.76 x 2.17 x 0.87 in). It can be installed on a desktop or wall-mounted.
Q6. What are the operating temperature and storage temperature ranges for the IOT-R41?
The IOT-R41 can operate within a certain temperature range and be stored within another temperature range. Please refer to the product manual or specifications for detailed information.
Q7. Can the IOT-R41 be used in environments with high humidity?
The IOT-R41 has a specified range of relative humidity within which it can operate safely. Please refer to the product manual or specifications for detailed information.