Lucci 213161 Air Ceiling fan Havana 15 cm Instruction Manual

213161 Air Ceiling fan Havana 15 cm
Instruction Manual LUCCI AIRFUSION HAVANA
CEILING MOUNTED OSCILLATING FAN

CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION.

THANK YOU FOR PURCHASING

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and  use of this ceiling fan. Please keep instructions for future reference.

SAFETY PRECAUTIONS

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Cleaning and maintenance shall not be undertaken by children without supervision.
2. Children should be supervised to ensure that they do not play with the appliance.
3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring rules.
4. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available.
5. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 16kg.
7. The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe. (Refer to the ‘Clearance requirement’ section for more information.)
8. This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of 2 walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be positioned in a location protected from water, wind, dust and salt. Exposure to these elements will void the warranty. Mounting the fan in a situation where it is subject to water or moisture is dangerous and may increase the risk of damage, injury or electrical shock and will void the warranty.
9. Must be assembled and installed by a licensed electrician.
10. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.
11. The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent or suitably qualified persons.
12. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension system shall be performed by the manufacturer, its service agent or suitably qualified persons.

PARTS LIST

• Unpack your ceiling fan carefully. Remove all parts and hardware.
• Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to  the place of purchase for inspection or replacement.
• Check whether the ceiling fan has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product  to the place of purchase for inspection, repair or replacement.
• Examine all parts, you should have the following:

1. Mounting bracket x 1
2. Fan motor assembly x 1
3. Fan blade bracket x 1
4. Fan bladesx 3
5. Fan blades fixing cap x 3
6. Fan blades screw x 9 (and 1 spare)
7. Screw for mounting bracket x 2
8. Remote receiver x 1 set
9. Remote transmitter x 1 set

CLEARANCE REQUIREMENT

• The fan must be installed so that the lowest point of the fan blade must be 2.3m from the floor (In Europe).
  NOTE: The lowest point of the fan blade is when the fan head is adjusted to 45°.

• The ceiling fan must be installed in a location so that the blades are a minimum 1M spacing from the tip of the blade to the nearest objects or walls.
  NOTE: Please be aware of that the fan head can be oscillating 60°. Please take this into consideration when selecting the installation location.

INSTALLATION OF THE MOUNTING BRACKET

• Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 16kg, with the two long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig. 3)

NOTE: The bracket screws provided are for use with wooden structures only. For structures other than wood, the appropriate screw type MUST be used. Ensure the screws  used are suitable for the mounting surface and the surrounding environment.

ANGLED CEILING INSTALLATION
This fan hanging system supportsa maximum 13 degree angled ceiling installation. (Fig.4)

INSTALLATION OF THE FAN BLADES

• Align the 3 mounting holes on the blade (3) to the 3 mounting holes of the blade bracket (2);
• Insert the fixing cap (4) into the mouting holes from the bottom of the blade (3) and secure by tightening the 3 screws (1) from the top of the blade bracket (2);
• Once completed, repeat the same process on the remaining blades.

• Install the assembled fan-blades (7) to the motor part (5);
• Tighten the 2 set screws (6) on the side of the motor shaft;

HANGING THE FAN

Lift the fan assembly onto the mounting bracket. Ensure thekey slot (A) of the hanger ball is positioned on the key pin (B) of the mounting bracket (C) to prevent the fan  from rotating when in operation.(Fig.7A)
NOTE: Please be aware of that the fan head can be oscillating 60°. There are key slots (Fig.7B) provided on the hanger ball which allow you to adjust the direction of the fan  according to your requirement.

ADJUSTMENT OF THE FAN HEAD

• Loosen the two set screws on both sides of the motor; (Fig.8)
• Rotate the fan head and aim the arm screw at the desired angle (There are only three angles available: 0°, 45°, 90°.They are labelled on the motor part) (Fig.9)
• Retighten the set screws after adjusting to the desired angle. Ensure the set screws are tighten and postioned well into the slot of the desired angle. (Fig.10)

ELECTRICAL WIRING DIAGRAM

WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED WIRING.
CAUTION: ENSURE THE EARTHING CONTINUNITY ON THE METAL BODY OF THE FAN TO THE EARTH TERMINAL AFTER CONNECTIING THE  MOUNTING BRACKET, REMOTE RECEIVER, AND FAN MOTOR WIRING CONNECTORS TOGETHER BEFORE POWERING ON.

FINISHING THE INSTALLATION

• After completing the electrical connection at the mounting bracket terminal block, connect the ceiling fan wiring via the quick connector plug.
  • Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the fan’s accessible metal body back to the earth terminal at the terminal  block on the mounting bracket.

• Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy and that the wires are not damaged during this step. Secure the  canopy to the hanger bracket using the screws provided. (Fig. 12 )

• Switch ON mains power supply to the fan. Test the fan operations or enjoy using the fan following instructions the under “USING YOUR CEILING FAN” section of this instruction manual.

USING YOUR CEILING FAN

BATTERY INSTALLATION IN THE REMOTE CONTROL (Fig.13)
Your ceiling fan is controlled by the remote control. The following must be considered before operating the remote.

1 x CR2032 3V battery is required for the remote control.
– Remove the screw (6) and Pull out the battery tray (2) by pressing the clip (1) and pulling out the battery tray together.
– Place the battery (3) on the tray and insert the tray back to remote hand set (4) indicated by “+” polarity symbol (5).
– Ensure the polarity is correct as shown in the battery compartment.
– Reinstall the screw (6) to secure the battery tray (2).

OPEARATION OF THE REMOTE CONTROLLER (Fig.14)

1. Control of the speed (HIGH, MEDIUM, LOW);
2. Fan On/Off;
3. Timing control of the fan (1Hr, 3Hr, 6Hr). The fan will be stopped automaticly after the time you selected.
4. 60° Oscillation On/Off

NOTE:
The remote has memory function if the mains power is turned off. It will recover from the last status when the power is turned on again.

EFFECTIVE LOCATION FOR THE INFRA-RED CONTROL (Fig.15)

The transmitter and receiver are communicated by infra-red signal. The remote controller must be operated within the ollowing distances:
Approximately 45° from the infra red sensor to the left & right.
Distance from transmitter to the infra red sensor: Max.3 meters.

INSTALLATION OF THE REMOTE HOLDER (Fig.16)

Install the remote holder onto the wall by the two screws provided, then place the remote controller onto the holder.

AFTER INSTALLATION

WOBBLE:
NOTE: Ceiling fans tend to move during operation due to the fact that they are mounted on a rubber grommet.
If the fan was mounted rigidly to the ceiling it would cause excessive vibration. Movement of a few centimetres is quite acceptable and DOES NOT suggest any problem.
TO REDUCE THE FAN WOBBLE: Please check that all screws which fix the mounting bracket and down rod are secure.

NOISE:
When it is quiet (especially at night) you may hear occasional small noises. Slight power fluctuations and frequencysignals superimposed in the electricity for off-peak hot  water control, may cause a change in fan motor noise. This isnormal. Please allow a 24-hour “settling-in” period, most noises associated with a new fan disappear during this  time.
The manufacturer’s warranty covers actual faults that may develop and NOT minor complaints such as hearing themotor run – All electric motors are audible to some extent.

CARE & CLEANING

NOTE: Always turn OFF the power at the mains switch before performing any maintenance or attempting to clean your fan.

• Every 6 months periodic cleaning of your fan is the only maintenance required. Use a soft brush or lint free cloth to avoidscratching the paint finish. Please turn off  electricity power when you do so.
• Do not soak or immerse your fan in the water or other liquids. It could damage the motor or the blades and create the possibility of an electrical shock.
• Ensure that the fan does not come in contact with any organic solvents or cleaners.
• To clean the fan blade, wipe with only a damp clean cloth with NO organic solvents or cleaners.
• The motor has a permanently lubricated ball bearing so there is no need to oil.

SAFETY AND PRECAUTION OF THE BUTTON BATTERY

To prevent false operation during battery insertion or replacement, this ceiling fan must be disconnected from the supply mains.

• WARNING – Keep new and used batteries away from children.
• CAUTION – Do not ingest battery—Chemical burn hazard.
• Batteries must be removed from the remote transmitter before it is discarded.
• Always use Lithium CR2032 battery type with this ceiling fan remote controller.
• Dispose of exhausted batteries immediately and safely (so they cannot be retrieved by children). Flat batteries can still be dangerous. Contact your local council to safely  dispose of the battery.
• Ensure the batteries are inserted with the correct polarity.
• Do not use rechargeable batteries in this product.
• Regularly check the product and make sure the battery box lid is correctly secured. If the battery compartment does not close securely, stop using the product and keep it away from children.
• Remove batteries from the product when not in use for long periods of time.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

TECHNICAL INFORMATION

Fan Type| Ceiling mounted, 60° oscillating fan
Model No./SKU#| LD-15’’ HAVA-ORB/ SKU# 213160| LD-15’’ HAVA-BLK/ SKU# 213161| LD-15’’ HAVA-CHW/ SKU# 213162
Colour| Orb| Black| White
Rated Voltage| 220-240V~ 50Hz
Rated Wattage| 55W ( 51W fan motor + 4W oscillation motor)
Battery for remote| CR2032 3V
Weight| 3.8kg
Size| Dia: 380mm   H: 550mm Max.
Canopy Dimensions| H: 60mm  Dia: 130mm

WARRANTY INFORMATION

IN EUROPE – If you are a European customer please contact the retail outlet where the fan was purchased for warranty service.

Contact:
Beacon International Ltd
Hong Kong Head Office: Room 05, 18/F, Kimberland Center, 55 Wing Hong Street, Cheung Sha Wan Kowloon, Hong Kong Tel +852 34915904 Fax +852 34915917
China showroom / Office: 11/Fl, Guzhen Lighting Building B, Mid Zhongxing Road, Guzhen, Zhongshan, GuangDong, China.

Tel: +86 760 8986 6388
Fax: +86 760 8986 6380
info@beaconinternational.com
www.beaconinternational.com
Beacon Lighting Europe GmbH
Campus Fichtenhain 42, 47807 Krefeld, Germany
TEL +49 (2151) 325 82 39 FAX +49 (2151) 325 70 65
sales@beaconlighting.eu
www.beaconlighting.eu

This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of 2 walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be positioned in a location protected from water, wind, dust and salt. Exposure to these elements will void the warranty. Mounting the fan in a situation where it is subject to water or moisture is dangerous.

References

• Homepage
• Beacon Lighting Europe – Fans and More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>