SUPERATV IN-PFWS-P-RAN1K XP Kinetic MaxDrive Power Flip Windshield Installation Guide
- June 16, 2024
- SUPERATV
Table of Contents
SUPERATV IN-PFWS-P-RAN1K XP Kinetic MaxDrive Power Flip Windshield
Product Information
Specifications
- Item Description: Windshield
- Top Frame: B
- Right Bracket: C
- Lower Frame: D
- Clamp: E (x4)
- Right Female Hinge: F
- Left Male Hinge: G
- Right Male Hinge: H
- Left Female Hinge: J
- Left Bracket: K
- Actuator Bracket 1: L
- Actuator Bracket 2: M
- Actuator Bracket 3: P
- Actuator Bracket 4: N
- Actuator: Q (x2)
- Gasket
- Bulb Seal
Product Usage Instructions
Installation Instructions:
- Do not discard packaging until the product has been successfully installed.
- Unless noted, do not completely tighten the hardware when assembling.
- SuperATV does not recommend keeping a Windshield installed while transporting on an open-air trailer. Remove or secure with straps.
- This item is not returnable if the protective film has been removed.
- Test fit to the cage to confirm fitment before removing the film.
Cleaning and Maintenance:
- To clean the Windshield, use a mild detergent, alcohol, or hand-washing soap.
- To prevent water spots, use a chamois to blot the Windshield dry.
Assembly:
- Use hand tools only when assembling.
- Do not use power tools.
Contact for Installation Help:
- Email: [email protected]
- Website: www.superatv.com
- Phone: 1-855-743-3427
Hours of Operation:
- Monday – Thursday: 8:00 am – 8:00 pm EST
- Friday: 8:00am – 7:00pm EST
- Saturday: 9:00am – 2:00pm EST
FAQ:
-
Q: Can I use power tools for assembly?
A: No, only hand tools should be used for assembly. -
Q: How do I clean the Windshield?
A: To clean the Windshield, use a mild detergent, alcohol, or hand washing soap. Blot dry with a chamois to prevent water spots. -
Q: Can I return the product if the protective film has been removed?
A: No, the product is not returnable if the protective film has been removed.
Safety Instruction
- Do not discard packaging until the product has been successfully installed.
- Unless noted, do not completely tighten the hardware when assembling.
- SuperATV does not recommend keeping a Windshield installed while transporting on an open-air trailer. Remove or secure with straps.
- This item is not returnable if the protective film has been removed.
- Test fit to the cage to confirm fitment before removing the film.
Windshield Cleaning:
- Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
- Do not use a windshield wiper blade or install a motorized windshield wiper
- Never use razor blades, scrapers, squeegees, brushes, etc.
- Thoroughly rinse the Windshield to float off dirt and mud.
- Using a soft cloth, or microfiber cloth, clean the Windshield with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand-washing soap can also be used.
- To prevent water spots, use a chamois to blot Windshield dry.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV’s® products could interfere with other aftermarket accessories. If the user has aftermarket products on the machine, contact SuperATV® to verify that they will work together. Although SuperATV® has thousands of satisfied customers, users should be aware that installing lift kits, long travel, suspension kits, tires, etc. will change the ride of the machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases the risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect users from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV® products, the user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of the seller to the user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by SuperATV®. SuperATV® parts and products are not warranted if the item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may violate the law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.
The Buyer is responsible for fully understanding the capability and limitations of his/her vehicle according to manufacturer specifications, warnings, and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings, and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Use hand tools only when assembling.
Kit Contents
| Item | Description |
|---|---|
| A | Windshield |
| B | Top Frame |
| C | Right Bracket |
| D | Lower Frame |
| E | Clamp x 4 |
| F | Right Female Hinge |
| G | Left Male Hinge |
| H | Right Male Hinge |
| J | Left Female Hinge |
| K | Left Bracket |
| L | Actuator Bracket 1 |
| M | Actuator Bracket 2 |
| N | Actuator Bracket 4 |
| P | Actuator Bracket 3 |
| Q | Actuator x 2 |
Installation
Textured side of the printed material, on the Windshield, will face inside.
To ease installation, soak the Seal in hot water before cutting or
installing to increase flexibility.
- Install Bulb Seal to Windshield (A) in the location shown.
- Install Gasket across the front of Frame in the location shown.
- Install Lower Frame (D) to Windshield (A) with the hardware shown.
- Install Top Frame (B), along with Right and Left Female Hinges (F-J), to the Windshield (A) with the hardware shown.
- Install the Left Bracket (K) to Windshield (A) with the hardware shown.
- Repeat for Right Bracket (C) installation.
- Tighten hardware.
- Place assembly on the machine.
- Insert the Right Male Hinge (H) into the Right Female Hinge (F).
- Secure the Right Male Hinge (H) to holes located in the Frame with the hardware shown.
- Repeat for the Left side.
- Align the Windshield to the machine and tighten the Hinge hardware completely.
- The windshield should open and close smoothly. See “Hinge Alignment” if binding occurs.
Hinge Alignment
Hinges to be in line with each other. Loosen hardware and adjust as necessary.
- Install Actuator Brackets (L)(N) to Clamps (E) with hardware shown.
- Secure Actuator (Q) with hardware shown.
- Repeat for the passenger side.
- Tighten hardware.
- Secure Clamps (E) to Cage.
- Repeat for the passenger side.
- Secure Actuators (Q) to Right Bracket (K) and Left Bracket (C) with hardware shown.
Before drilling any holes, check behind the area to be drilled for any interference.
Switch Mounting
- Users may install Switch in a location different than shown.
- Verify that Harnesses will reach the Switch before mounting.
- Remove stock Knockout or cut a new location.
- Connect the wiring and secure the Switch.
Mounting Slot:
Before permanently mounting the Switch, SuperATV recommends testing after all components have been installed.
- Secure Wires, from Actuators to Cage; use provided wire ties.
- Reinstall the Cup Holder.
Contact Information
Need help with your installation?
- [email protected]
- www.superatv.com
- 1-855-743-3427
- 8:00am – 8:00pm EST M-Th
- 8:00am – 7:00pm EST Friday
- 9:00am – 2:00pm EST Saturday
© 2022 SuperATV.com®. All Rights Reserved.