AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon User Manual

AstroAI ASIKFCWR Wide Neck Plastic Foam Cannon

INTRODUCTION

Thank you for purchasing the AstroAI Wide Neck Plastic Foam Cannon.

This product is designed to clean any vehicle. With the dense and rich foam that sprays from this product, you easily can remove dirt on the vehicles, greatly reducing the risk of fine grit damage to the car lacquer surface, and extending the smooth finish of automotive paint to bring you a perfect car washing experience. This product can also be used on motorcycles, floors, windows, etc.

Thank you again for choosing AstroAl, if you have any questions or concerns regarding your product, please contact us at support@astroai.com.

Please fully read and understand this manual before using this product. Keep this manual for future reference.

WARNING

• Do not put the touch-free automobile detergent and the car washing wax into the foam cannon. These two products have strong coagulability and it is easy to block the foaming device and cause damage.
• This product is equipped with a 1/4″ quick connection plug. Before purchasing, ensure your pressure washer is compatible with this connector.
• Please use this product within a 1000-3000 PSI water pressure range.
• Please ensure that the pressure washer’s water supply is clean and free of blockages.
• If you turn on the water and the foam cannon starts sprinkling out a small amount of water, or if no water comes out, immedi­ately turn off your pressure washer. Check the pressure washer and foam cannon.
• Please do not aim the spray nozzle at people or animals when using it, doing so may cause serious injury.
• Please promptly turn off the pressure washer after use. The pressure washer should not be used for more than 30 minutes.
• Please clean and dry the tools after use to avoid corrosion and blockage caused by chemical residues after use.
• Please store this product in a ventilated, dry, and cool place.

PACKAGE INCLUDES

• Foam Cannon x 1
• User Manual x 1
• Warranty Card x 1

SPECIFICATIONS

• Capacity: 1 L
• Material: Brass, Nylon, PE
• Applicable Pressure Range: 1 000-3000 PSI

PRODUCT COMPONENTS

PRODUCT SIZE

USING INSTRUCTIONS

1. Pour the cleaning solution into the foam cannon and dilute it with an appropriate amount of hot or warm water.
2. After screwing on the foam cannon’s nozzle, connect it to the pressure washer connector. Ensure there is a secure connection.
3. Adjust the top knob to control the amount of foam. Rotate it clockwise to produce more foam and counterclockwise to produce less foam, and adjust it to the right position before starting the pressure washer.
4. Rotate the nozzle clockwise to produce fan-shaped foam; rotate the nozzle counterclockwise to gradually reduce the fan-shaped area. Adjust to the desired position before starting the pressure washer.
5. Aim the nozzle at the ground before starting the pressure washer. This is to avoid loose connections which may cause the front end to fly out and smash vulnerable objects.
6. After confirming that the product is firmly connected to the pressure washer connector, spray the foam evenly on the car body and clean it.
7. Please clean and dry the tools and place them in a cool and ventilated place after use.

TROUBLESHOOTING

• Trouble The foaming effect is poor after usage over time

  • Solution The foam maker is blocked.
    (Clean or replace the foam maker. Cleaning method: soak it in a weak acid detergent and hot water for some time and then rinse).

• Trouble The connector of the pressure washer is leaking

  • Solution The connector’s seal ring is misplaced or damaged. (Adjust or replace the connector’s sealing ring ).

• Trouble There is no foam, only water

  • Solution The inner core is loose.
    (Remove the 1 /4 quick connector with a clamp and tighten the inner core with a screwdriver).

• Trouble Foam is very thin
  Solution

  • Adjust the top knob clockwise.
  • Increase the solubility of the washing fluid in the bottle.

RECYCLING

You may dispose of the product when its service life has ended, please recycle the recyclable parts according to local guidelines.

WARRANTY PERIOD

2-Year Limited Warranty from AstroAI

• Each AstroAI Wide Neck Plastic Foam Cannon will be free from defects in material and workmanship.
• This warranty does not cover damage from neglect, misuse, contam­ination, alteration, accident, or abnormal conditions of operation or handling.
• This warranty covers the original purchaser only and is not transfer­able.
• AstroAI always wants to provide our customers with excellent products as well as customer service.

If you have any questions or concerns, please contact us via support@astroai.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>