LAP PRJ26504 Integrated LED Bulkhead Instruction Manual

**LAP PRJ26504 Integrated LED Bulkhead Instruction Manual

**

Integrated LED bulkhead

IMPORTANT – These instructions are for your safety. Please read through them thoroughly prior to handling the product and retain them for future reference.

Parts

You will need

Care & maintenance

Safety

IMPORTANT Do not use with a dimmer switch.
IMPORTANT , Retain for future reference: read carefully

• These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.
• All fittings must be installed by a competent person in accordance with local regulations (IET wiring regulation BS7671).
• Check the pack and make sure you have all of the parts listed.
• Remove all packaging, wrap etc from the product.
• Decide on the appropriate location for your product.
• CAUTION: IP44 is guaranteed when the product is properly installed and sealed.
• Always avoid the product to be located at corrosive environment.
• Always refer to the installation drawing for the orientation of the product.
• The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other fixings not supplied and must be purchased.
• Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
• IMPORTANT: The fixing point(s) selected must be capable of supporting the full weight of the light fitting.
• Wiring diagram is for reference only. Always refer to the terminal marking for wiring. Ensure that all electrical connections are tight and that no loose strands are left out of the terminal block.
• Never put anything on the product or hang anything on any part of this product.
• Never use the terminal cables to bear the product weight.
• This light use microwave motion detection, it may detect occupants through doors, glass windows or thin walls. The range detection can be adjusted by the button (DIP switch).
• Non-replaceable control gear.
• When the product does not light after installation:
  • Ensure there is no electricity failure
  • Ensure all the connections are secured
• If you have any doubt about installation/use of this product, consult a qualified electrician.
• Always disconnect the product from mains at least 10 minutes allowing to cool down before any maintenance or adjustment.
• It is recommended to have a regular schedule of care and maintenance to keep the surface condition well.

Technical Data

be replaced by the manufacturer or his service agent or a similar qualified person. Do not stare at the operating light source
Frequency range:| 5725 – 5875 MHz
Transmitter power:| 4 dBm
| This product complies with conformity requirements of the applicable European Regulations or Directives.
| This product complies with conformity requirements of the applicable UK Regulations
Energy efficiency class:| This product contains a light source of energy efficiency class .
| Class II product – Double Insulated – No earth required.
IP44| Splashproof
| Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
| Caution! Risk of electric shock!
| Do not use with a dimmer switch.
xxWyy:| xx-year; yy-week of the year

Guarantee

We take special care to select high quality materials and use manufacturing techniques that allow us to create products incorporating design and durability. This product has a manufacturer’s guarantee of 5 years against manufacturing defects, from the date of purchase (if bought in store) or date of delivery (if bought online), at no additional cost for normal (nonprofessional or commercial) household use.

To make a claim under this guarantee, you must present your proof of purchase (such as a sales receipt, purchase invoice or other evidence admissible under applicable law), please keep your proof of purchasein a safe place. For this guarantee to apply, the product you purchased must be new, it will not apply to second hand or display products. Unless stated otherwise by applicable law, any replacement product issued under this guarantee will only be guaranteed until expiry of the original period guarantee period.

This guarantee covers product failures and malfunctions provided theproduct was used for the purpose for which it is intended and subject to installation, cleaning, care and maintenance in accordance with the information contained in these terms and conditions, in the user manual and standard practice, provided that standard practice does not conflict with the user manual.

This guarantee does not cover defects and damage caused by normal wear and tear or damage that could be the result of improper use, faulty installation or assembly, neglect, accident, misuse, or modification of the product. Unless stated otherwise by applicable law, this guarantee will not cover, in any case, ancillary costs (shipping, movement, costs of uninstalling and reinstalling, labour etc), or direct and indirect damage.

If the product is defective, we will replace or refund, within a reasonable time.

Rights under this guarantee are enforceable in the country in which you purchased this product. Guarantee related queries should be addressed to the store you purchased this product from.

The guarantee is in addition to and does not affect your statutory rights.

Troubleshooting

circuit breaker/internal wall switch.
The light fixture is not properly attached to the mounting plate, if this is a new installation (the pins are not fully seated in the terminal block).| Re- install the light fixture to the base and ensure the pins are fully seated in the terminal block.
Another light source is causing the unit to think it is daylight.| Check the wiring connections, ensure no connections are loose.
The light comes on during the day| Unit is located at shaded area| Shine a flashlight onto the sensor. If the light turns off then the fixture is mounted in an area that does not allow enough light to enter the sensor. Relocate the product.
The light comes on for no apparent reason.| The product is wired through a dimmer or timer.| Do not use a dimmer or timer to control the product. Replace the dimmer or timer with a standard on/ off wall switch.
The lights stay on continuously.| The product is wired through a dimmer or timer.| Do not use a dimmer or timer to control the product. Replace the dimmer or timer with a standard on/ off wall switch.
The lights flash on and off.| Heat or light from the bulbs may be turning the sensor on and off.| Relocate the unit, away from the light source.
Sensor is sensing reflected light from the light fixture.|

1. Change position of light head aim light away from the reflecting surfaces.
2. Relocate the unit to a different location where it no longer causes reflected light

Sensor will not operate at night.| Wiring inside electrical came loose.| Check that circuit breaker and/or wall switch power is on.
No power is being delivered to the fixture| Turn off surrounding lights and/or relocate the unit.
Light does not switch off after set time has elapsed| Time is set for too long.| Reduce time (TIME knob).
Continuous movement in the detection zone.| Change detection zone / Relocate the unit.
Light being operated in the detection zone causing sensor to respond as a result of change in temperature.| Change detection zone / Relocate the unit.

Installation

IMPORTANT DO NOT USE WITH A DIMMER SWITCH.
IMPORTANT! RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.

L = Brown or Red
N = Blue or Black
E = Green / Yellow

WARNING: this drawing is for reference only. Consult a professional electrician to install according to relevant national wiring rules. If being fitted in a bathroom a 30mA RCD must be used.
This product is suitable for bathroom hazard zones as specified by the following water drop image :

Use

Detection distance and angle

Aim to the desired area

Timer

ON

Sensor

ON

Lux

EU DECLARATION OF CONFORMITY

Product

• ALMAGRO Bulkhead 28cm White sensor / DAVENPORT 28cm white with sensor
• ACL1010-M

Name and address of the manufacturer or his authorised representative:

Kingfisher International Products B.V.,
Rapenburgerstraat 175E,
1011 VM Amsterdam,
The Netherlands

This declaration of conformity is issued under the sole responsibility of the manufacturer:

Object of the declaration

Product

Model: EAN

ALMAGRO Bulkhead 28 cm White sensor DAVENPORT 28 cm white with sensor

ACL1010-M; 5063022044563 5063022047465

The object of the declaration described above is in conformity with the relevant Union harmonization legislation:

2014/53/EU as amended Radio Equipment Directive

References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared:

EN 60598-1: 2015 + A1:2018
EN 60598-2-4: 2018
EN 61347-2-13: 2014 + A1:2017
EN IEC 62031 : 2020+A11:2021
EN 61347-1: 2015
EN 62493: 2015
EN IEC 60598-1: 2021,
EN IEC 60598-2-1: 2021

BS EN IEC 55015: 2019 + A11; 2020
BS EN 61547: 2009
BS EN IEC 61000-3-2: 2019+A1:2021
BS EN 61000-3-3: 2013+A1:2019
BS EN 61000-3-3: 2013+A2:2021
BS EN 50663: 2017
ETSI EN 300 440 V2.1.1: 2017-03
ETSI EN 301 489-3 V2.1.1: 2019-03
ETSI EN 301 489-1 V2.2.3: 2019-11
EN IEC 55015: 2019 + A11:2020
EN 61547; 2009
EN IEC 61000-3-2: 2019
EN 61000-3-3: 2013 + A1:2019
EN 50663: 2017

Remark: This equipment has been tested and found to comply with the limits for a ETSI EN 300 440
V2.1.1 receiver category 1.

Signed for and on behalf of

Kingfisher International Products B.V.,
Rapenburgerstraat 175E,
1011 VM Amsterdam,
The Netherlands

David Awe
Group Quality Director
15/01/2023

Manufacturer

UK Manufacturer:
Kingfisher International Products Limited,
1 Paddington Square, London, W2 1GG,
United Kingdom

EU Manufacturer:
Kingfisher International Products B.V. Rapenburgerstraat 175E,
1011 VM Amsterdam
The Netherlands

www.diy.com / www.screwfix.com / www.screwfix.ie
To view instruction manuals online,
visit www.kingfisher.com/products
Made in China

www.castorama.fr / www.bricodepot.fr / www.screwfix.fr
Pour consulter les manuels d’instructions en ligne,
rendez-vous sur le site www.kingfisher.com/products
Fabriqué en RPC

www.castorama.pl
Aby zapoznać się z instrukcją obsługi online,
odwiedź stronę www.kingfisher.com/products
Wyprodukowano w ChRL

www.bricodepot.ro
Pentru a consulta manualele de instrucţiuni online,
vizitaţi www.kingfisher.com/products
Fabricat în China

www.bricodepot.es
Para consultar los manuales de instrucciones en línea,
visite www.kingfisher.com/product
Fabricado en China

www.bricodepot.pt
Para consultar manuais de instruções online,
visite www.kingfisher.com/products
Fabricado na China

Ithalatçı Firma:
KOÇTAŞ YAPI MARKETLERİ TİCARET A.Ş.
Sırrı Çelik Bulvarı Otokoç Blok No:9 Çekmeköy /
İstanbul 34788 Türkiye
Telefon: (90) 216 430 03 00
Faks : (90) 216 484 43 13
www.koctas.com.tr
Kullanım kılavuzuna internet üzerinden ulaşmak
için www.kingfisher.com/products adresini ziyaret edin
Yetkili servis istasyonları ve yedek parça temini için asagıda yer alan Koçtas Müsteri Hattı ve
Koçtas Genel Müdürlük irtibat bilgilerinden faydalanınız.
KOÇTAŞ MÜŞTERİ HİZMETLERİ
0850 209 50 50
AEEE Yönetmeliğine Uygundur
Menşei: Çin

References

• Brico Depôt | Bricolaje, jardín, construcción y climatización
• Brico Depôt | Bricolage, construção, jardim e climatização
• Bricolage, jardinage et aménagement de la maison | Castorama
• B&Q | DIY Products at Everyday Low Prices | DIY at B&Q
• KoçtaÅŸ | Evimi Çok Seviyorum

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>