iiyama ProLite TF2738MSC-B2 Computer Monitor User Manual

iiyama ProLite TF2738MSC-B2 Computer Monitor

Thank you very much for choosing the iiyama LCD monitor.

We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.

Dear user, congratulations on the purchase of your iiyama LCD.

For details on warranty and locally used pixel policies that apply directly after installation of your product, please check the iiyama website. To report a fault, please contact your local support center found at www.iiyama.com/service.

For technical details, please visit “Specifications and Datasheet”

Things to check before you call the iiyama information line:

1. Is the power cable connected securely and turned on?
2. Has the display been turned on?
3. Is the signal cable connected securely, and is the correct input selected?
4. Has the computer been restarted with the display connected?
5. Is the graphics card correctly installed with the latest drivers possible?
6. Has the correct native resolution been selected via ‘Display Properties’?
7. Is the R/G/B signal configuration correct?
8. Is the display’s On-Screen Menu shown?
9. Have the correct brightness and contrast settings been set?
10. Have given display tolerances and compatibility been considered?
11. Have you performed a Factory Reset/Recall via the On-Screen Menu?

Before reporting the screen defect, please prepare the following information/evidence:

• Model number
• Purchase receipt and serial number
• Name and address for collection
• Telephone/fax number for availability during the day
• Convenient collection date (date, time)
• Short description of the defect

Important Note:

• If there is no fault found in the collected equipment after inspection, the transferring party shall incur charges for transport and administration.
• If you have checked all of the above and there is still no picture, call our information line for assistance in your country.
• See the identification plate on the back of the case.

CE MARKING DECLARATION OF CONFORMITY

This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC Directive”, 2014/35/EU “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU “RoHS Directive”.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.

• IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands
• Model No. : PL2738M

We recommend recycling of used products. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address: http://www.iiyama.com

You can access the Web pages of different countries from there.

• We reserve the right to change specifications without notice.
• All trademarks used in this user manual are the property of their respective owners.
• Eprel registration number TF2738MSC-B2: 426849

FOR YOUR SAFETY

SAFETY PRECAUTIONS

WARNING

• STOP OPERATING THE MONITOR IF YOU ARE AWARE OF ANY PROBLEMS
  If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock.

• NEVER REMOVE THE CABINET
  High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.

• DO NOT PUT ANY OBJECT INTO THE MONITOR
  Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause fire, electric shock or damage.

• INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
  The monitor may cause an injury if it falls or is dropped.

• DO NOT USE THE MONITOR NEAR WATER
  Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric shock.

• OPERATE UNDER THE SPECIFIED POWER SUPPLY
  Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will cause malfunction and may cause fire or electric shock.

• PROTECT THE CABLES
  Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy objects on the cables. If damaged, the cables may cause fire or electric shock.

• ADVERSE WEATHER CONDITIONS
  It is advisable not to operate the monitor during a heavy thunderstorm as the continual breaks in power may cause malfunction. It is also advised not to touch the plug in these circumstances as it may cause electric shock.

CAUTION

• INSTALLATION LOCATION
  Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor.

• DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
  The monitor may topple and cause injury if not suitably located. Please also ensure that you do not place any heavy objects on the monitor and that all cables are routed such that children may not pull the cables and possibly cause injury.

• MAINTAIN GOOD VENTILATION
  Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fire. To allow adequate air circulation, place the monitor at least 10cm (or 4 inches) from any walls.
  In case the monitor will be installed inside a kiosk or any other equipment, please make sure enough ventilation is available to avoid overheating of the monitor. Contact the iiyama service center in case you need advice.

• DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
  When you move the monitor, turn off the power switch, unplug the monitor, and be sure the signal cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.

• UNPLUG THE MONITOR
  If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents.

• HOLD THE PLUG WHEN DISCONNECTING
  To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself as this may cause fire or electric shock.

• DO NOT TOUCH THE PLUG WITH WET HANDS
  Pulling or inserting the plug with wet hands may cause electric shock.

• WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
  Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage your computer.

• REMARK FOR 24/7 USAGE
  This product is not specifically designed for 24/7 usage in all environments.

OTHERS

ERGONOMIC RECOMMENDATIONS

• To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches) away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour is recommended as looking at the screen continuously can cause eye strain.

SPECIAL NOTES ON LCD MONITORS

• The following symptoms are normal with LCD monitors and do not indicate a problem.

NOTE

• When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position.
• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen can be recovered slowly by changing the image or turning off the Power Switch for some hours.

CUSTOMER SERVICE

NOTE: If you have to return your unit for service and the original packaging has been discarded, please contact your dealer or iiyama service center for advice or replacement packaging.

CLEANING

• WARNING:  If you drop any materials or liquids such as water into the monitor when cleaning, unplug the power cable immediately and contact your dealer or iiyama service center.
• CAUTION: For safety reasons, turn off the power switch and unplug the monitor before you clean it.
• NOTE:
• • To protect the LCD panel, do not scratch or rub the screen with a hard object.
  • Never use any of the following strong solvents. These will damage the cabinet and the LCD screen.
  • Thinner: Benzine
  • Abrasive cleaner: Spray-type cleaner
  • Wax: Acid or Alkaline solvent
  • Touching the cabinet with any product made from rubber or plastic for a long time may cause degeneration or loss of paint on the cabinet.

CABINET:

• Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
• Then wipe the cabinet with a soft dry cloth.

LCD SCREEN:

• Periodic cleaning with a soft dry cloth is recommended.
• Don’t use tissue paper etc. because these will damage the LCD screen.

BEFORE YOU OPERATE THE MONITOR

FEATURES

• Supports Resolutions up to 1920 × 1080
• High Contrast 1000:1 (Typical) / Brightness 500cd/m2 (Typical), 425cd/m2 (with Touch panel)
• Digital Character Smoothing
• Automatic Set-up
• Stereo Speakers 2 × 3W Stereo Speakers
• Standby Feature (VESA DPMS Compliant)
• VESA Mounting Standard (200mm×100mm, 100mm×100mm) Compliant
• IPX1 Standard Compliant (Only front face)

CHECKING THE CONTENTS OF THE PACKAGE

The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama office.

• Power Cable*
  mDP-DP Cable

• Safety Guide

• HDMI Cable

• USB Cable

• Quick Start Guide

• DisplayPort Cable

• Cable Cover

CAUTION

• • TO USERS IN 120V AREA
• The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using a power supply higher than this rating, then a power cable with a rating of 10A/250V must be used. However, all guarantees and warranties are void for any problems or damage caused by a power cable or AC adapter not supplied by iiyama.
• An approved power cable greater or equal to H05VVF, 3G, 0.75mm2 must be used.

INSTALLATION

WARNING: Before installation, make sure the wall, ceiling or desktop arm is strong enough to hold the necessary weight of the display and the mount.

< WALL MOUNTING >

WARNING: When you use with the wall mounting, in consideration of the thickness of the mounting stage, tighten the M4 Screws (4 pcs) with a washer whose “L” length is 8mm(VESA mounting holes) or 8mm(Outer mounting holes) to fasten the monitor. Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor.

< BUILT-IN EQUIPMENT >

WARNING

• This product is not designed to be used in high-temperature environments.
• If the product is placed in an external cabinet, you need to design cooling fans and vents to keep the temperature low enough to fit in the product temperature specification.

< ROTATING THE DISPLAY >

The monitor is designed to be compatible with both landscape and portrait modes. Video cards for portrait display will be required for rotating the image on the screen.

CONTROLS AND CONNECTORS

1. Menu Button (MENU)
2. Scroll Up / Audio Adjust Button ( )
3. Scroll Down / i-Style Color Button ( )
4. Select / Input Select Button (ENTER)
5. Power Switch ( )
6. Speakers
7. Power Indicator
   • NOTE
   • Blue: Normal operation
   • Orange: Standby mode
8. USB Connector (USB)
9. Audio Connector (AUDIO IN)
10. HDMI Connector (HDMI)
11. DVI-D Connector (DVI)
12. DisplayPort Connector (DP)
13. AC Connector( : Alternating current) (AC POWER IN)

CONNECTING YOUR MONITOR

1. Ensure that both the computer and the monitor are switched off.
2. Connect the computer to the monitor with the signal cable.
3. Connect the computer to the monitor with the USB Cable.
4. Connect the Power Cable to the monitor first and then to the power source.
5. Turn on your monitor and computer.

NOTE

• Make sure that the building installation has a circuit breaker of 120/240V, 20A (maximum).
• The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office.
• Make sure you tighten the finger screws at each end of the Signal Cable.
• The Class I pluggable equipment Type A must be connected to protective earth.
• The socket outlet shall be installed near the equipment and shall be easily accessible.

[Example of Connection]

• DVI-D cable is not supplied with the monitor. If you use low-quality DVI-D cable, it may cause a result of electromagnetic interference. Please contact the iiyama Support Centre in your country if you wish to connect the monitor via the DVI input.

[Fitting and Removal of Cable Cover]

Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with the front face down.

< Fitting >

1.  Remove the screw from the monitor as shown in Step1.
2. Connect the cables, as shown in Step 2, place the cable cover and fix it firmly using a screw.

Step 1

Step 2

< Removal > 

1. Remove the screw and the cable cover as shown in Step 3.

Step 3

COMPUTER SETTING

• Signal Timing
  Change to the desired signal timing listed on page 22: COMPLIANT TIMING.

• TOUCH support operation system

The other OS Versions not listed are not supported.

• : Supported
• : Not supported
• • 1 Gesture can be supported by application programs.
• • 2 Please download the Mac driver from the following website.
    • https://www.touch-base.com/oem/weida/
    • And, please use the “V6” driver for this model.
• • 3 When you install the gesture driver (http://touch-base.com/documentation/Gestures.html_ Installation_and_running), it can support 2 – 4 finger gestures (definition be Apple Inc.)
• • 4 As Android is very diverse, check with your device manufacturer if your device supports the touch function (for software developers; the controller is PID: 2575/ VID: 0402)
• • 5 Windows XP / Vista is not supported by Microsoft anymore.
• • 6 Chrome OS is supported. Chrome OS is auto-updating and based on the (latest) Linux kernel.

Touch Input Settings in Dual Screen Mode

• Connect the primary monitor to the computer first.
• Set Control Panel > Hardware and Sound > Tablet PC Settings > Display > Setup.

The following message will appear on the screen. Please follow the instructions.

After setting, connect a second monitor and perform the setup as in.

NOTE

• The monitors are recognized as dual-display, and touch operation cannot be performed on two monitors at the same time.
• You can perform touch operations on only one of the monitors.

OPERATING THE MONITOR

To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 22. You are also able to adjust the picture by following the button operation shown below.

1. Press the 1 Button to start the On Screen Display (OSD) feature. There are additional Menu items that can be switched by using the Buttons.
2. Select the Menu item which contains the adjustment icon relating to the adjustment you want to make. Press the 2 Button. Then, use the Buttons to highlight the desired adjustment icon.
3. Press the 2 Button again. Use the Buttons to make the appropriate adjustment or setting.
4. Press the 1 Button to leave the menu, and the settings you just made will be automatically saved.

For example, to correct for the OSD vertical position, select the Menu item of Setup Menu and then press the Button. Then, select the OSD Position by using the Buttons.

An adjustment page appears after you press the 2 Button. Then, select OSD V.Position by using the Buttons. Press the 2 Button again. Then, use the Buttons to change the OSD vertical position settings. The OSD vertical position of the overall display should be changing accordingly while you are doing this.

Press the 1 Button last, it ends, and all changes are saved in the memory.

NOTE

• When button operations are aborted during adjustment, the On-Screen Display disappears when the time set for the OSD Time Out has passed. Also, the button can be used to return previous menu and turn off the On-Screen Display.
• Any changes are automatically saved in the memory when the On Screen Display disappears. Turning off the power should be avoided while using the Menu.

ADJUSTMENT MENU CONTENTS

Picture Adjust| |
---|---|---
Adjustment Item| Problem / Option| Button to Press

Contrast *3

| Too dull

Too Intense

Brightness *1,2,3

| Too dark Too bright

Adv. Contrast *2,3,4

| Off| Typical Contrast Ratio
On| Increased Contrast Ratio

ECO Mode *3

| Off| Normal
1| The brightness of the backlight is reduced.
2| The brightness of the back-light is reduced by more than 1.
3| The brightness of the back-light is reduced by more than 2.

Overdrive *5

| Off / -2 / -1 / 0 / +1 / +2

It will improve the gray-level response time of the LCD panel.

A higher level results in a faster response time.

• • 1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright. Can not select when Adv. Contrast is On.
• • 2 Brightness and Adv. Contrast can not be enabled at the same time when ECO Mode is on.
• • 3 Contrast, Brightness, Adv. Contrast and ECO Mode adjustments are disabled when i-Style Color is activated.
• • 4 To activate the option, mark it in the setup menu. To deactivate it, remove the marking.
• • 5 Overdrive can only be enabled when the input refresh rate is 60Hz.

Input Select

Adjustment Item| Problem / Option Button to Press

Input Select

| DVI| Select the DVI input.
HDMI| Select the HDMI input.
DisplayPort| Select the DisplayPort input.
Auto| Search for an available input source and select it automatically.
NOTE Input source is fixed, not selected automatically when DVI, HDMI, and DisplayPort which

are selected.

Direct

You can skip the Menu items and directly display an option setting screen by using the following button operations.

• Input Select: Press the 2 Button when the Menu is not displayed.

Audio Adjust

Adjustment Item| Problem / Option Button to Press

Volume

| Too soft Too loud

Mute *1                                     Direct

| Off| Return the sound volume to the previous level.
On| Turn off the sound temporarily.

Audio Input *2

| HDMI| Select the HDMI input.
DisplayPort| Select the DisplayPort input.
Line-In| Select the Line-In input.

• • 1 To activate the option, mark it in the setup menu. To deactivate it, remove the marking.
• • 2 Suitable for HDMI and DisplayPort input only.
• Direct: You can skip the Menu items and directly display an option setting screen by using the following button operations.
• Audio Adjust: Press the Button when the Menu is not displayed.
• Mute:
  • Pressing and holding the Button for about 2 seconds when the Menu is not displayed.
  • Mute and Unmute are switched as follows by pressing the Button successively.

**Color Adjust ***

Adjustment Item| Problem / Option Button to Press
Cool| Bluish white
Normal| Greenish white
Warm| Reddish white

User Color

| Red| Too weak Too strong
Green
Blue

i-Style Color              Direct

| Off| Return to a state set by color adjustment except i-Style Color.
Standard| For general Windows environment and monitor

default setting.

Game| For PC game environment.
Cinema| For movie and video environments.
Scenery| For displaying outdoor scenery images
Text| For text editing and viewing in a word processing environment.

• Color Adjust is disabled when Blue Light Reducer is activated.

  • Direct: You can skip the Menu items and directly display an option setting screen by using the following button operations.
    • i-Style Color: Press the Button when the Menu is not displayed.

Manual Image Adjust

Adjustment Item| Problem / Option Button to Press

Sharpness

|

1 / 2 / 3 / 4 / 5

You can change the picture quality from 1 to 5 (soft to sharp). Press the Button to change the picture quality in numerical order. Press the Button to change the picture quality in reverse numerical order.

Adjust the picture quality at resolutions of less than 1920 x 1080.

You can change the picture quality (5 steps).

Video Mode Adjust| Full Screen| Full-screen display
Aspect Ratio *1| Expansion display of Aspect

Blue Light Reducer *2 Direct

| Off| Typical
1| Blue light is reduced.
2| Blue light is reduced more than Mode1.
3| Blue light is reduced more than Mode2.

X-res Technology

| Off| Normal
Soft| Enhance the picture edge.
Middle| Enhance the picture edge more than the Soft option.
Hard| Enhance the picture edge more than the

Middle option.

• • 1 It can display in the center of the screen with a 4:3, 5:4, or 16:10 aspect ratio when input video resolution is 4:3, 5:4, or 16:10.
• • 2 Blue Light Reducer is disabled when Color Adjust is activated.

Direct: You can skip the Menu items and directly display an option setting screen by using the following button operations.

• Blue Light Reducer: Pressing and holding the 2 Button for about 2 seconds when the Menu is not displayed.

Setup Menu Setup Menu

Adjustment Item| Problem / Option                                       Button to Press

Language Select

| English| English| Русский| Russian
Français| French|

| Japanese
Deutsch| German| | Simplified Chinese
Nederlands| Dutch| | Traditional Chinese
Polski| Polish|

OSD Position

| OSD

H.Position

| OSD is too left                                        OSD is too right
OSD

V.Position

| OSD is too low                                        OSD is too high

OSD Time Out

| You can set the OSD display duration time. 5 / 15 / 30 / 60 seconds

OSD Background*

| Off| Retune the background of OSD.
On| The background of OSD is made transparent.

Opening Logo*

| Off| iiyama Logo does not display when the monitor is

turned on.

On| iiyama Logo is displayed when the monitor is turned on.

LED*

| Off| The Power Indicator is turned Off.
On| The Power Indicator is turned On.
NOTE **** Turn Off the Power Indicator when you are bothered by the light.

• To activate the option, mark it in the setup menu. To deactivate it, remove the marking.

Memory Recall

Adjustment Item| Problem / Option Button to Press

Memory Recall

|

Factory-preset data is restored.

Lock Mode

< OSD Menu>

• The OSD lock will be activated by pressing the front buttons 1 and for about 5 seconds. If you try to access the OSD by pressing any of the buttons 1, , and 2, the message “OSD Locked” will appear on the screen.
• The OSD lock will be deactivated by pressing the front buttons 1 and again for 5 seconds.

< Power Switch>

1. The power switch lock will be activated by pressing the front buttons 1 and for 5 seconds. Locking the power switch means that won’t be able to turn off the Monitor while the power switch is locked. If press the power switch message “Power Button Locked” will appear on the screen.
2. The power switch lock will be deactivated by pressing the front buttons 1 and again for about 5 seconds.

STANDBY FEATURE

The standby feature of this product complies with the power-saving requirement of VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use.

To use the feature, the monitor needs to be connected to a VESA DPMS-compliant computer. There is a standby step the monitor takes as described below. The standby function, including any timer settings is configured by the operating system. Check your operating system manual for information on how this can be configured.

Standby Mode

When the video signal from the computer is off, the monitor enters into Standby Mode which reduces the power consumption to less than 1.5W*. The screen becomes dark, and the power indicator turns to orange. From Standby Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again.

• USB peripherals and audio equipment are not connected.

NOTE: Even when using the standby mode, the monitor consumes electricity. Turn off the Power Switch whenever the monitor is not in use, during the night and on weekends, to avoid unnecessary power consumption.

TROUBLESHOOTING

If the monitor fails to operate correctly, please follow the steps below for a possible solution.

1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists.
3. If you are experiencing a problem that is not described below or you cannot correct the problem, discontinue using the monitor and contact your dealer or iiyama service center for further assistance.

socket.
(The power indicator does not light up.)| – The Power Switch is turned ON.
| – The AC socket is live. Please check with another piece of equipment.
(Power indicator is blue.)| – If the blank screen saver is in active mode, touch the keyboard or the mouse.
| – Increase the Contrast and/or Brightness.
(Power indicator is orange.)| – If the monitor is in standby mode, touch the keyboard or the mouse.
| – The computer is ON.
The screen is not synchronized.| – The Signal Cable is properly connected.
| – The signal timing of the computer is within the specification of the monitor.
The screen position is not in the center.| – The Signal Cable is properly connected.
| – The signal timing of the computer is within the specification of the monitor.
The screen is too bright or too dark.| – The video output level of the computer is within the specification of the monitor.
The screen is shaking.| – The power voltage is within the specification of the monitor.
| – The signal timing of the computer is within the specification of the monitor.
No sound.| – The audio equipment (computer etc.) is ON.
| – The Audio Cable is properly connected.
| – The Volume is turned up.
| – The Mute is OFF.
| – The audio output level of the audio equipment is within the specification of the monitor.
The sound is too loud or too quiet.| – The audio output level of the audio equipment is within the specification of the monitor.
A strange noise isheard.| The Audio Cable is properly connected
The touch screen shows no response.| The USB Cable is firmly seated in the socket.

Touch screen driver software is installed.

  The touch position does not deviate.| The calibration function set up correctly.

RECYCLING INFORMATION

For better environment protection please don’t dispose of your monitor. Please visit our website: www.iiyama.com to monitor recycling.

APPENDIX

Design and specifications are subject to change without prior notice.

SPECIFICATIONS

ProLite TF2738MSC-B2

Touch Screen

| Technology| Projected capacitive 10pt touch
---|---|---
Light transmission| 85%
Hardness| 6H
Total thickness| 3.6mm
Communication system| USB serial transfer
Size Category| 27″

LCD

Panel

| Panel technology| IPS (In-Plane-Switching)
Size| Diagonal: 27″ (68.6cm)
Pixel pitch| 0.3114mm H × 0.3114mm V
Brightness| 500cd/m2 (Typical), 425cd/m2 (with Touch panel)
Contrast ratio| 1000 : 1 (Typical: with Touch panel)
Viewable angle| Right / Left : 89 degrees each, Up / Down: 89 degrees each (Typical)
Response time| 14ms (Typical), 5ms (Gray to Gray)*3
Display Colors| Approx.16.7M
Sync Frequency| Horizontal: 30-80kHz, Vertical: 55-75Hz
Maximum Resolution| 1920 × 1080, 2.1 MegaPixels
Input Connector| DVI-D, HDMI, DisplayPort
Plug & Play| VESA DDC2BTM
Input Video Signal| Digital: DVI (Digital Visual Interface Standard Rev.1.0) compliance

Digital: HDMI, DisplayPort

Input Audio Connector| ø 3.5mm mini jack (Stereo)
Input Audio Signal| 1.0Vrms maximum
Speakers| 3W × 2 (Stereo speakers)
Maximum Screen Size| 597.6mm W × 336.2mm H / 23.5″ W × 13.2″ H
Power Source| 100-240VAC, 50/60Hz 0.7A
Power Consumption*1| 25W typical, Standby mode: 1.5W maximum
Dimensions / Net Weight| 648.5 × 386.5 × 52.0mm / 25.5 × 15.2 × 2.0″ (W×H×D)

8.3kg / 18.3lbs

Environmental Considerations

| Operating:    Temperature    5 to 35°C / 41 to 95°F Humidity          10 to 80% (No condensation)

Storage:      Temperature    -20 to 60°C / -4 to 140°F Humidity          5 to 85% (No condensation)

Approvals| CE, UKCA, TÜV-Bauart, EAC, IPX1*2

NOTE

• • 1 USB peripheral and audio equipment are not connected.
• • 2 IPX1 Standard Compliant : Only front face
• • 3 When set to Overdrive +2.

DIMENSIONS

COMPLIANT TIMING

640 × 480

| 31.469kHz| 59.940Hz| 25.175MHz
37.500kHz| 75.000Hz| 31.500MHz
37.861kHz| 72.809Hz| 31.500MHz

800 × 600

| 35.156kHz| 56.250Hz| 36.000MHz
37.879kHz| 60.317Hz| 40.000MHz
46.875kHz| 75.000Hz| 49.500MHz
48.077kHz| 72.188Hz| 50.000MHz

1024 × 768

| 48.363kHz| 60.004Hz| 65.000MHz
56.476kHz| 70.069Hz| 75.000MHz
60.023kHz| 75.029Hz| 78.750MHz
1280 × 1024| 63.981kHz| 60.020Hz| 108.000MHz
79.976kHz| 75.025Hz| 135.000MHz
1440 × 900| 55.935kHz| 59.887Hz| 106.500MHz
1680 × 1050| 65.290kHz| 60.000Hz| 146.250MHz
1920 × 1080| 66.590kHz| 59.930Hz| 138.500MHz

Frequently Asked Questions

How do I adjust the screen position if it doesn't fit properly when I turn on the iiyama ProLite TF2738MSC-B2 monitor?

You can adjust the screen position by accessing the On-Screen Display (OSD) through the 1 Button. Then, select the relevant adjustment, such as Position or Horizontal/Vertical Position, and use the Buttons to reposition the screen.

Can I use iiyama ProLite TF2738MSC-B2 monitor for extended periods without worrying about overheating?

The monitor has ventilation slots to prevent overheating. However, if you plan to use it in a kiosk or enclosed space, ensure proper ventilation. Contact iiyama service for advice in such cases.

What do I do if the power cable or signal cable gets damaged?

If the cables are damaged, it's essential to replace them promptly. Damaged cables can pose fire or electric shock risks. Contact your dealer or iiyama service center for suitable replacements.

How do I rotate the screen display between landscape and portrait modes?

To rotate the display, you'll need video cards that support portrait display. Once you have the necessary hardware, you can change the screen orientation through your computer's display settings.

What is the maximum resolution supported by iiyama ProLite TF2738MSC-B2 monitor?

The iiyama ProLite TF2738MSC-B2 supports resolutions up to 1920x1080, ensuring high-quality visuals.

Is iiyama ProLite TF2738MSC-B2 monitor suitable for gaming or professional use?

This monitor's high resolution and touch functionality make it suitable for a range of applications, including gaming and professional use. However, for specific requirements, consider your intended use and monitor specifications.

What do I do if I encounter touchscreen calibration issues?

If you experience touchscreen calibration problems, access the touch settings through the OSD and recalibrate the touchscreen. Follow the on-screen instructions for calibration.

Can I use iiyama ProLite TF2738MSC-B2 monitor with a Mac computer?

Yes, iiyama ProLite TF2738MSC-B2 monitor is compatible with Mac computers. Download the necessary Mac driver from the provided website and use the V6 driver for iiyama ProLite TF2738MSC-B2 model.

How do I adjust the Contrast and Brightness settings on the monitor?

You can adjust the Contrast and Brightness settings through the Picture Adjust menu. Press the respective buttons to increase or decrease contrast and brightness levels according to your preferences.

What is ECO Mode, and how does it affect the monitor's performance?

ECO Mode is a feature that reduces the backlight brightness to save energy. You can choose from three different levels of ECO Mode, each reducing the backlight brightness to varying degrees. It's a useful feature for energy- conscious users.

What is the Overdrive setting, and how does it impact the monitor's display quality?

Overdrive is a feature that can improve the gray-level response time of the LCD panel, resulting in faster response times. You can select different levels of Overdrive, and higher levels lead to faster response times. This can be beneficial for reducing motion blur in fast-paced content, but it's essential to find the right balance for your needs.

How do I change the input source on the monitor?

You can change the input source by accessing the Input Select menu. Use the buttons to navigate and select between DVI, HDMI, DisplayPort, and the Auto option to automatically detect the input source.

Download The PDF link:iiyama ProLite TF2738MSC-B2 Computer Monitor User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>