iiyama GB2730QSU G-Master LCD Monitor User Manual

GB2730QSU G-Master LCD Monitor
User Manual

Thank you very much for choosing the iiyama LCD monitor.
We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
iiyama I Servicecard
Dear user, we congratulate you on the purchase of your iiyama LCD.
For details on warranty and locally used pixel policies that apply directly after installation of your product please check the Ilyama website.
To report a fault, please contact your local support centre found at www.iiyama.com/service
Things to check before you call the Ilyama information line
I if the power cable is connected securely and turned on?
I if the display has been turned on? I if the signal cable is connected securely and the correct Input selected?
I if the computer has been restarted with the display connected?
I if the graphics card is correctly installed with the latest drivers possible?
I if the correct native resolution has been selected via Display Properties’?
I If the NM signal configuration is correct? I if the displays On Screen Menu is shown?
I if the correct brightness and contrast settings have been set?
I if given display tolerances and compatibility have been considered?
I if via the On Screen Menu you have performed a Factory Reset/Recall?
Before reporting the screen defect, please prepare the following information/evidence:
I model number’
I purchase recePI and serial number
I name and address for collection
I telephonelax number, for avalabilly Curing the day
I convenient collection date (date. bme)
I short destuipeon of be defect
Important Note:
If Mere is no fault found in the cotected etpaunenl after inspection. the transfenng party shall Into charges for uansporl and administration.
If you have checked all of the above and there is still no picture. call our Information line for assistance in your country.

CE MARKING DECLARATION OF CONFORMITY

This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC Directive”, 2014/35/EU “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU “RoHS Directive”.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands
Model No. : PL2730Q
We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address:
http://www.iiyama.com
You can access the Web page of different countries from there.

• We reserve the right to change specifications without notice.
• All trademarks used in this user manual are the property of their respective owners.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
• Eprel registration number : G-MASTER GB2730QSU-B1 C : 359248

FOR YOUR SAFETY

SAFETY PRECAUTIONS
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in power may cause malfunction. It is also advised not to touch the plug in these circumstances as it may cause electric shock.
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not place any heavy objects on the monitor, and that all cables are routed such that children may not pull the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fire. To allow adequate air circulation, place the monitor at least 10cm (or 4 inches) from any walls. When removing the tilt stand, the ventilation slots on the back side of the monitor can be blocked. This may overheat the monitor and may cause fire or damage. Make sure to allow enough ventilation when removing the tilt stand. Operating the monitor on its back, side, upside down or on a carpet or any other soft material may also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage your computer.
CAREFUL! PROTECT YOUR HANDS AND FINGERS

• Be careful not to hurt your fingers or hands when you change the height or the angle.
• Injury can occur if care is not taken to avoid finger contact with the displays base when adjusting the height. (Just for height adjustable model.)

REMARK FOR 24/7 USAGE
This product is not specifically designed for 24/7 usage in all environments.
OTHERS
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches) away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour is recommended as looking at the screen continuously can cause eye strain.
2 FOR YOUR SAFETY

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE

• When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position.
• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen can be recovered slowly by changing the image or turning off the Power Switch for some hours.

CUSTOMER SERVICE
NOTE

• If you have to return your unit for service and the original packaging has been discarded, please contact your dealer or iiyama service center for advice or replacement packaging.

CLEANING
WARNING

• If you drop any materials or liquids such as water into the monitor when cleaning, unplug the power cable immediately and contact your dealer or iiyama service center.

CAUTION

• For safety reasons, turn off the power switch and unplug the monitor before you clean it.

NOTE

• To protect the LCD panel, do not scratch or rub the screen with a hard object.
• Never use any of the following strong solvents. These will damage the cabinet and the LCD screen.
  Thinner| Spray-type cleaner
  ---|---
  Benzine| Wax
  Abrasive cleaner| Acid or Alkaline solvent
• Touching the cabinet with any product made from rubber or plastic for a long time may cause degeneration or loss of paint on the cabinet.

Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
CABINET
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then wipe the cabinet with a soft dry cloth.
LCD SCREEN
Periodic cleaning with a soft dry cloth is recommended.
Don’t use tissue paper etc. because these will damage the LCD screen.

BEFORE YOU OPERATE THE MONITOR

FEATURES

• Supports Resolutions up to 2560 × 1440
• High Contrast 1000:1 (Typical), Adv. Contrast Function Available / Brightness 350cd/m  (Typical)
• Supports AMD Radeon FreeSync™ technology
• Flicker – Free
• Quick Response Time 1ms (Gray to Gray)
• Blue Light Reducer
• Digital Character Smoothing
• 2 × 2W Stereo Speakers
• VESA Mounting Standard (100mm×100mm) Compliant
•  Keyhole for Security Lock

CHECKING THE CONTENTS OF THE PACKAGE

• Power Cable*
•  USB Cable
• Quick Start Guide
• HDMI Cable
• Stand-Base with a screw”?
• DisplayPort Cable
• Safety Guide

CAUTION

• The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using a power supply higher than this rating, then a power cable with a rating of 10A/ 250V must be used. However, all guarantees and warranties are void for any problems or damage caused by a power cable not supplied by iiyama. An approved power cable greater or equal to H05VVF, 3G, 0.75mm2 must be used.

INSTALLATION

WARNING

• Before installation, make sure the wall, ceiling or desktop arm is strong enough to hold the necessary weight of the display and the mount.

< WALL MOUNTING >
WARNING

• When you use with the wall mounting, in consideration of thickness of the mounting stage, tighten the M4 Screws (4pcs) with washer which “L” length is 7mm to fasten the monitor. Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor.
  

< ROTATING THE DISPLAY >
The monitor is designed to be compatible with both landscape and portrait modes. Video card for portrait display will be required for rotating the image on the screen. With Stand:
NOTE

• Adjust the monitor’s height before panel rotation.
• Attempting to rotate the panel forcibly without adjusting the stand height may cause damage to the panel or the stand.

FITTING AND REMOVAL OF BASE

CAUTION

• Put the monitor on a stable surface. The monitor may cause injury or damage if it falls or is dropped.
• Do not give a strong impact to the monitor. It may cause damage.
• Unplug the monitor before removal or installation to avoid an electric shock or a damage.

< Installation>

1. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.
2. Lay the monitor flat on a table with front face down.
3. Install the stand-base as shown on above picture.
4. Use the ‘thumb screw’ provided to secure the base to the monitor.

< Removal>

1. Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.
2. Loosen the ‘thumb screw’ to remove the Stand-Base from the monitor.

CONTROLS AND CONNECTORS

1. Power Indicator
   NOTE   Blue: Normal operation Orange: Standby mode

2. Power Switch ( )

3. Menu / Select Button (ENTER)

4. Scroll Up / Volume Button ( )

5. Scroll Down / ECO Mode Button ( )

6. Exit Button (EXIT)

7. Input Select Button (INPUT)

8. Speakers

9. USB Downstream Connector ( , 5V, 900mA)

10. USB Upstream Connector ( )

11. Keyhole for Security Lock
    NOTE You can fasten a security lock and cable to prevent the monitor from being removed without your permission.

12. DisplayPort Connector (DP)

13. HDMI Connector (HDMI)

14. DVI-D Connector (DVI-D)

15. Cable Hole

16. Headphone Connector (LINE OUT)

17. Audio Connector (LINE IN)

18. AC Connector ( : Alternating current) ( )

CONNECTING YOUR MONITOR

• Ensure that both the computer and the monitor are switched off.
• Connect the computer to the monitor with the signal cable.
• Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features.
• Connect the Power Cable to the monitor first and then to the power source.
• Turn on your monitor and computer.

NOTE

• Make sure that the building installation has a circuit breaker of 120/240V, 20A (maximum).

• The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both
  the monitor and the computer. The cable supplied with the monitor is for a standard connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office.

• Make sure you tighten the finger screws at each end of the signal cable.

• The Class I pluggable equipment Type A must be connected to protective earth.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

• Excessive sound pressure from ear-/headphones can cause hearing damage/hearing loss.

[Example of Connection]

• DVI dual-link cable is not supplied with the monitor. If you use low quality DVI dual-link cable, it may cause a result of electro-magnetic interference. Please contact the iiyama Support Centre in your country if you wish to connect the monitor via the DVI input.
  [ Collect Cables ]
  Put the cables through the cable hole to bundle them.

DISCONNECTING YOUR MONITOR

1. Ensure that both the computer and the monitor are switched off.
2. Disconnect the power source first and then the Power Cable from the monitor.
3. Disconnect the signal cable from the computer and the monitor.
4. Disconnect the audio cable from the computer and the monitor.

COMPUTER SETTING

• Signal Timing
  Change to the desired signal timing listed on page 25: COMPLIANT TIMING.

ADJUSTING THE HEIGHT AND THE VIEWING ANGLE

• For optimal viewing it is recommended to position yourself directly opposite to the full face of the monitor, then adjust the monitor’s height and angle to your own preference.
• Hold the panel so that the monitor does not topple when you change the monitor’s height or angle.
• You are able to adjust the monitor’s height up to 130mm, angle up to 45° right and left, 22° upward and 5° downward.
  

NOTE

• Do not touch the LCD screen when you change the height or the angle. It may cause damage or break the LCD screen.
• Careful attention is required not to pinch your fingers or hands into the moving part of the stand when you change the height or the angle.
• Injury can occur if care is not taken to avoid finger contact with the displays base when adjusting the height.

  ---

OPERATING THE MONITOR

To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 25. You are also able to adjust the picture by following the button operation shown below.

1. Press the ENTER Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the Buttons.
   

2. Select the Menu item which contains the adjustment icon relating to the adjustment you want to make. Press the ENTER Button. Then, use the / Buttons to highlight the desired adjustment icon.

3. Press the ENTER Button again. Use the Buttons to make the appropriate adjustment or setting.

4. Press the EXIT Button to leave the menu, and the settings you just made would be automatically saved.

For example, to correct for OSD vertical position, select Menu item of Setup Menu and then press the ENTER Button. Then, select OSD Vertical Position by using the Buttons. An adjustment page appears after you press the ENTER Button.
Then, use the Buttons to change the OSD vertical position settings. The OSD vertical position of the overall display should be changing accordingly while you are doing this.
Press the EXIT Button lastly, it ends, all changes are saved in the memory.
NOTE

• When button operations are aborted during adjustment, On-Screen Display disappears when the time set for the OSD Time has passed. Also, press the EXIT button to quickly turn off the OnScreen Display.
• Any changes are automatically saved in the memory when the On Screen Display disappears. Turning off the power should be avoided while using the Menu.
• All adjustments have only one setting which applies to all signal timings.

ADJUSTMENT MENU CONTENTS

Too bright
Brightness *1,2,4| Too dull
Too intense
Overdrive| Off / -2 / -1 / 0 / +1 / +2
It will improve the gray level response time of the LCD panel.
A higher level results in a faster response time.
Adv. Contrast| Off| Typical Contrast Ratio
On| Increased Contrast Ratio
ECO Direct| Off| Normal
Mode1| Brightness of back-light is reduced.
Mode2| Brightness of back-light is reduced more than Mode1.
Mode3| Brightness of back-light is reduced more than Mode2.
Blue Light Reducer| Off| Typical
Mode1| Blue light is reduced.
Mode2| Blue light is reduced more than Mode1.
Mode3| Blue light is reduced more than Mode2.
Black Tuner| From -5 to +5
You can adjust Dark shades.
Color Saturation| Too weak
Too strong
Gamma| You can set the Gamma. 1.8 / 2.2 / 2.6

OPERATING THE MONITOR 13

• Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright.
• Contrast and Brightness adjustments are disabled when Adv. Contrast mode is activated.
• Picture Adjust adjustment is disabled when i-Style Color is activated.
• Brightness adjustment is disabled when ECO is activated.
  Direct
  You can skip the Menu items and directly display an option setting screen by using the following button operations.
  ECO : Press the Button when the Menu is not displayed.

automatically.
Manual| DVI| Select the Digital (DVI) input.
HDMI| Select the Digital (HDMI) input.
DisplayPort| Select the Digital (DisplayPort) input.
NOTE Input source is fixed, not selected automatically when DVI, HDMI and DisplayPort which are selected.

Direct
You can skip the Menu items and directly display an option setting screen by using the following button operations.

• Input Select : Press the INPUT Button when the Menu is not displayed.

Volume
Direct| Too soft
Too loud
Mute Audio| Off| Return the sound volume to the previous level.
On| Turn off the sound temporarily.
NOTE Mute On and Off are switched as follows by pressing the  Button successively.

Audio Input *| HDMI| Select the HDMI input.
DP| Select the DisplayPort input.
Line-In| Select the Line-In input.

• Suitable for HDMI/DisplayPort input only.
  Direct
  You can skip the Menu items and directly display an adjustment scale by using the following button operations.
  Volume : Press the Button when the Menu is not displayed.

NOTE You can memorize your customized monitor settings.
The following settings can be memorized:
Contrast, Brightness, Overdrive, Adv. Contrast, ECO mode, Volume, Mute
Audio, Color Setting, i-Style Color, Sharp and Soft, Black Tuner, Video Mode Adjust

Color Temperature

|  9300K| Bluish white
 7500K| Greenish white
 6500K| Reddish white
User Preset|  Red| Too weak
Too strong
Green
 Blue

• Color Settings adjustments are disabled when i-Style Color or Blue Light Reducer is activated.

adjustment except i-Style Color.
 Standard| For general windows environment and monitor default setting.
Sport Game| For Sports game environment.
 FPS Game| For FPS game environment.
 Strategy Game| For Strategy game environment.
Text| For text editing and viewing in a word processing environment.
 Mode 1| Applies customized monitor settings.
 Mode 2| Applies customized monitor settings.
 Mode 3| Applies customized monitor settings.
Sharp and Soft| 1 2 3 4 5 6
You can change the picture quality from 1 to 6 (sharpto soft).
Press the Button to change the picture quality in numerical order.
Press the Button to change the picture quality in reverse numerical order.
HDMI RGB Range|  Full| For full-range color scale signal
 Limited| For limited color scale signal
Video Mode Adjust 2| Full| Expansion display
 Aspect 3| Expansion display of Aspect

• i-Style Color adjustment is disabled when Blue Light Reducer is activated.

• Only HDMI/DisplayPort inputs.

• Option unavailable with 16:9 resolution.
  Direct
  You can skip the Menu items and directly display an option setting screen by using the following button operations.

  •  i-Style Color : Press the EXIT Button when the Menu is not displayed.

OSD is too right
OSD Vertical  Position| OSD is too low
OSD is too high
OSD Time| You can set the OSD display duration time between 5 and 30 seconds.

Opening Logo

| Off| iiyama Logo does not display when the monitor is turned on.
On| iiyama Logo displayed when the monitor is turned on.
FreeSync *| Off| The FreeSync function is turned off.
On| Enable the FreeSync function.

• Only DisplayPort input.
  Displays information regarding the current input signal coming from the graphic card in your computer.
  NOTE See your graphic card user guide for more information about changing the resolution and refresh.

● Lock Mode
< OSD Menu>

1. The OSD lock will be activated by pressing the front button ENTER for about 10 seconds. If you try to access the OSD by pressing any of the buttons, message “OSD Locked” will appear on the screen.
2. The OSD lock will be deactivated by pressing the front button ENTER again for about 10 seconds.

< Power Switch>

1. The power switch lock will be activated by pressing the front button ****for about 10 seconds. Locking the power switch means that won’t be able to turn off the Monitor while the power switch is locked. If presses the power switch message “Power Button Locked” will appear on the screen.
2. The power switch lock will be deactivated by pressing the front button ****again for about 10 seconds.

STANDBY FEATURE

The standby feature of this product complies with power saving requirement of VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a standby step the monitor takes as described below. The standby function, including any timer settings is configured by the operating system. Check your operating system manual for information on how this can be configured.
Standby Mode
When the video signal from the computer is off, the monitor enters into Standby Mode which reduces the power consumption to less than 0.5W*. The screen becomes dark, and the power indicator turns to orange. From Standby Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again.

• USB peripherals and audio equipment are not connected.
  NOTE
  Even when using the standby mode, the monitor consumes electricity. Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption.

TROUBLE SHOOTING

If the monitor fails to operate correctly, please follow the steps below for a possible solution.

1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists.
3. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your dealer or iiyama service center for further assistance.

The picture does not appear.
(Power indicator does not light up.)|  The Power Cable is firmly seated in the socket.
 The Power Switch is turned ON.
 The AC socket is live. Please check with another piece of equipment.
(Power indicator is blue.)|  If the blank screen saver is in active mode, touch the keyboard or the mouse.
 Increase the Contrast and/or Brightness.
 The computer is ON.
 The Signal Cable is properly connected.
 The signal timing of the computer is within the specification of the monitor.
(Power indicatoris orange.)|  If the monitor is in standby mode, touch the keyboard or the mouse.
 The computer is ON.
 The Signal Cable is properly connected.
 The signal timing of the computer is within the specification of the monitor.
The screen is not synchronized.|  The Signal Cable is properly connected.
 The signal timing of the computer is within the specification of the monitor.
The screen position is not in the center.|  The signal timing of the computer is within the specification of the monitor.
The screen is too bright or too dark.|  The video output level of the computer is within the specification of the monitor.
The screen is shaking.| The power voltage is within the specification of the monitor.
The signal timing of the computer is within the specification of the monitor.
No sound.| The audio equipment (computer etc.) is ON.
The Audio Cable is properly connected.
The Volume is turned up.
The Mute is OFF.
The audio output level of the audio equipment is within the specification of the monitor.
The sound is tooloud or too quiet.| The audio output level of the audio equipment is within the specification of the monitor.
A strange noise isheard.| The Audio Cable is properly connected.

RECYCLING INFORMATION

For better environment protection please don’t dispose your monitor.
Please visit our web site: www.iiyama.com for monitor recycling.

APPENDIX
Design and specifications are subject to change without prior notice.

SPECIFICATIONS

Size Category

|

27″

---|---
LCD Panel| Panel technology| TN
Size| Diagonal: 27″ (68.5cm)
Pixel pitch| 0.233mm H × 0.233mm V
Brightness| 350cd/m2 (Typical)
Contrast ratio| 1000 : 1 (Typical), Adv. Contrast Function Available
Viewable angle| Right / Left : 85° each, Up / Down : 80° each (Typical)
Response time| 1ms (Gray to Gray)
Display Colors| Approx. 16.7M

Sync Frequency

| DVI: Horizontal: 30.0-89.0kHz, Vertical: 50-76Hz HDMI: Horizontal: 30.0-89.0kHz, Vertical: 50-76Hz
DisplayPort(without FreeSync): Horizontal: 30.0-89.0kHz, Vertical: 50-75Hz DisplayPort(with FreeSync): Horizontal: 30.0-117.0kHz, Vertical: 48-75Hz
Native Resolution| 2560 × 1440, 3.7 MegaPixels
Support max. resolution| DVI: 2560 × 1440 60Hz
HDMI: 2560 × 1440 70Hz
DisplayPort(without FreeSync): 2560 × 1440 75Hz
DisplayPort(with FreeSync): 2560 × 1440 75Hz
Input Connector| DVI-D, HDMI, DisplayPort
Plug & Play| VESA DDC2BTM
Input Video Signal| DVI (Digital Visual Interface Standard Rev.1.0) compliance
HDMI, DisplayPort
USB Standard| USB3.0 (DC5V, 900mA)
Number of USB Ports Connector shape| 1 Upstream : Series B
2 Downstream : Series A
Input Audio Connector| ø 3.5mm mini jack (Stereo)
Input Audio Signal| 1.0Vrms maximum
Headphone Connector| ø 3.5mm mini jack (Stereo)
Speakers| 2W × 2 (Stereo speakers)
Maximum Screen Size| 596.7mm W × 335.7mm H / 23.5″ W × 13.2″ H
Power Source| 100-240VAC, 50/60Hz, 1.5A
Power Consumption*| 30W typical, Standby mode: 0.5W maximum
Dimensions / Net Weight| 613.5× 412.0 – 542.0 × 230.0mm / 24.2 × 16.2
– 21.3 × 9.1″ (W×H×D) 6.6kg / 14.5lbs

Angle

| Tilt: Upward: 22°
Downward: 5°
Swivel: Left/Right: 45° each
Rotation: Clockwise/Counterclockwise: 90° each

Environmental Considerations

| Operating: Temperature :5 to 35°C/41 to 95°F
Humidity :10 to 80% (No condensation)
Storage: Temperature-20 to 60°C/-4 to 140°F
Humidity 5 to 85% (No condensation)
Approvals| CE, TÜV-GS, EAC

**NOTE*** USB peripheral and audio equipment are not connected.

DIMENSIONS

COMPLIANT TIMING

Video Mode| Horizontal Frequency| Vertical Frequency| Dot Clock
---|---|---|---
640 × 480| 31.469kHz| 59.940Hz| 25.175MHz
800 × 600| 37.879kHz| 60.317Hz| 40.000MHz
1024 × 768| 48.363kHz| 60.004Hz| 65.000MHz
1280 × 1024| 63.981kHz| 60.020Hz| 108.000MHz
1600 × 1200| 75.000kHz| 60.000Hz| 162.000MHz
1680 × 1050| 65.290kHz| 60.000Hz| 146.250MHz
1920 × 1080| 66.590kHz| 59.930Hz| 138.500MHz
2560 × 1440| 88.787kHz| 59.951Hz| 241.500MHz
104.045kHz| 69.923Hz| 274.680MHz
111.788kHz| 74.920Hz| 298.470MHz

NOTE

• DVI : Use the DVI-D dual-link signal cable.
• DisplayPort input only.

References

• iiyama

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>