INJORA AX6S 2.4GHz 4CH Digital Radio Control System Instruction Manual
- June 16, 2024
- INJORA
Table of Contents
INJORA AX6S 2.4GHz 4CH Digital Radio Control System
For your safety as well as that of others, please read this manual thoroughly before installation and operation of your digital proportional R/C system.
Danger
If the operator does not operate by following the instructions, the operator
may lead to serious injuries, even mortal danger.
WARNING
if the operator does not operate by following the instructions, the Operator
may lead to serious injuries, even mortal danger.
Attention
If the operator does not operate by following the instructions, the
operator may lead to minor injuries, but generally, it will not cause serious
injuries to the operator.
WARNING
Read the ENTIRE instruction manual to become familiar with the features of the
product before operating. Failure to operate the product correctly can result
in damage to the product, and personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It needs to have basic mechanical skills ability, careful operation by common sense. Failure to operate this Product safely and responsibly could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision Do not attempt disassembly, use with incompatible components or augment the product in any way without the approval. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, before assembly, setup or use, to operate correctly and avoid damage or serious injury.
Age Recommendation
Not for Children under 14 years.
Attention
This product is only used for remote control cars or boats. Disclaims all
liability outside of the intended purpose and will not provide warranty
service related.
SAFETY PRECAUTIONS
- Always ensure all bakeries have been properly charged before using the model.
- Always check all servos and their connections before each run.
- Never operate your model near spectators, parking areas or any other area that could result in injury to people or property damage.
- Never operate your model during adverse weather conditions. Poor visibility can cause disorientation and loss of control of your model.
- If at any time during the operation of your model, you observe any erratic or abnormal operation immediately stop operation of your model until the cause of the problem has been ascertained and corrected.
- Stop before use please turn off the receiver power and then close the transmitter power. If the above operations are reversed. it might lead to uncontrolled and cause Accident.
INSTALLING THE TRANSMITTER BATTERIES
Remove the battery cover, insert 4X”AA” batteries with the correct polarity
and replace the battery cover.
Attention
- Please select new and the same brand alkaline batteries.
- Need to ensure that the battery polarity is correct, incorrect installation may cause transmitter damage.
- Please remove the battery if long time do not use the transmitter.
BATTERY LED MONITOR
INSTALLING THE RECEIVERS
Ine alter in paring protects he recover sim brain. Posta resent trials and away from the vehicle in an antenna tube
CAUTION
Do not cut the antenna. To prevent loss of radio range do not kink or cut the
black wire. do not bend or cut the metal tip, and do not bend or cut the white
wire at the end of the metal tip.
BINDING THE RECEIVER TO THE TRANSMITTER
Our products are well-matched in the factory, you do not need to match by yourself. But if you are going to match the receiver with another transmitter, or you need to change a new receiver or transmitter, please follow the following steps:
Note: we receive to shoot system, don’t follow other brands and permits!
- Install the battery to the 2.4G transmitter and shut it down.
- Insert the matching lines to the channel BIND/CH3 port of the receive (Figure .1)
- Connect the receiver battery to the VCC port of the receiver, At the same time the two LEDs are flashing and this means the receiver is going to the matching status.
- Press and hold the button on the transmitter, and then switch on the power supply.
- Observe the LED on the receiver, if find that the LED is not flashing anymore that means successfully Matched. (This process about 3s)
- Release the match button on the transmitter, and take out the match line.
- Install the server and then test.
- If the tests fail, please repeat the action above
- If the tests are successful. then insert the power supply port into VCC. match complete.
Server to setup
If the steering or throttle channel in the opposite direction, will the
transmitter channel switch back accordingly?
ADJUSTING THE STEERING TRIM
The steering trim dial is used to adjust the steering angle when the wheel is
centred Rotating the dial changes the steering angle(the steering in the
centre), Normally, the steering trim is adjusted until
the vehicle tracks straight. The steering trim dial is used to adjust the
steering angle when the wheel is centred Rotating the dial changes the
steering angle(the steering in the centre), Normally, the steering trim is
adjusted until the vehicle tracks straight.
- As you adjust steering! trim to the right, the wheels move to the right.
ADJUSTING THE THROTTLE TRIM
The throttle trim dial adjusts the throttle trim when the throttle trigger is
in neutral(centre). If the wheels rotate forward or backward when the throttle
trigger is at neutral, turn the throttle trim dial until the wheels stop
rotating.
ADJUSTING THE STEERING RATE
Adjusting the steering rate can help you to change the wheel steering range.
Turn the steering rate the steering rate
Counterclockwise to reduce the amount of steering. Reduce the steering if the
vehicle turns too fast. Clockwise to increase the amount of steering. Increase
the steering if the vehicle turns too slow.
The IN FAIL-SAFE FUNCTION
Function
Failsafe aims to prevent out-of-control driving of RC Cat or RC Boat If the
Receiver is not able to receive any signal, from the control to Throttle the
parameter of Throttle on the Receiver will turn back to its original setting.
Setting
- Turn on the Transmitter switch;
- Turn on the Receiver switch the LED will be lighting;
- Adjust the transmitter’s Throttle, make the car/boat stop flameout, then keep still.
- Press the”Setting” button on the Transmitter (as in the pic below) the LED will flash and then stop after 3 seconds.
- Which means the setting is finished.
Turn on the Transmitter switch
Turn off the Transmitter switch
Serve of Throttle will turn back to its original setting automatically The
setting is successful if the above procedures are finished completely
CAUTION
Always set the throttle trigger to neutral or full brake position and the
steering servo to neutral position in case of any unexpected control error!
Factory pre-settings for RC car Fail-safe.
Electric Car-Steering servo at neutral, throttle at neutral. Nitro Car-
Steering servo at neutral. throttle at idle.
2.4GHz TROUBLESHOOTING GUIDE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>