JBC B·IRON 210 DUAL Battery Powered Soldering Station Instruction Manual

JBC B·IRON 210 DUAL Battery Powered Soldering Station

Packing List

The following items are included:

Features and Connections

Quick Start

Display Holder Assembling

• Insert the thin end of the display holder into the upper area of the rear rail of the charging base (1). Then carefully rotate the display holder 90 degrees (2) until it stands vertical.

Display Holder Setting

• Insert the fi xing knob (3) and tighten it just enough so that it stays in its place but the display holder can be moved.

Display Placing

• Place the display on the support with its buttons facing upwards and adjust the height of the display holder.
• Once the display holder is at the right height, tighten the fixing knob completely to fix the display in place.

Base Connection /Display Connection

• Connect the charging base to the mains (4).
• If needed, the display can be connected to the USB port (5) with the provided USB cable to keep it charging while working.

Turning on the Portable Display

• Turn on the display by holding down the power button and then open the B·IRON app*:

Note: The app can also be downloaded to your own devices. To know how, see the section “Installing and Updating the B·IRON App”.

Tool Holder Angle Adjustment

• Adjust the tool holder angle by simply rotating it forward or backward (1) to the desired working position (2). Tool holders have 7 different positions, each varying by an angle of 10 degrees.
• Do not rotate the tool holder with a tool resting on it.

Cartridge Insertion and Charging

Inserting

• Place the tool over a cartridge and press the tool down to insert the cartridge (1). To release the tool with the cartridge from the extractor, lift the tool upward (2).

Fixing

• Make sure that the cartridge is appropriately inserted* into the tool by gently pressing the tip against the holes on the sides of the cartridge exchanger (3).

Important: Cartridges must be inserted up to the mark for a proper connection.

Charging

• Place the tool on the tool holder (4) to charge it. A beep will sound to confirm that the tool is properly placed and charging. The sound can be turned up, down or off using the buttons on the display.

Note: Charge the tool completely before using it for the first time. It will take aprox. 60 min for B210, approx. 30 min for B115 and aprox. 40 min for BP115.

• For more information on how to change cartridges and the use of the cartridge exchanger, see section “Cartridge Exchanger and Cartridge Holder”.

Compatible Cartridges

• B210 Handle works with C210 Cartridges. Find the model that best suits your soldering needs at www.jbctools.com.

Tool Selection

• Select the tool from the device list. If the tool is not displayed on the screen, make sure that the cap is off and the tool has some battery. Try scanning again by tapping Scan (6) on the display.
• To add a second tool to the station once the first one is connected, go to the main menu (7) and tap Add device. Select your second tool from the device list.

Status Lightband

The status light band indicates as following the tool status:

Safety Cap and Cap Holder

• Thanks to the safety cap for B210 and B115 handles, tools can be safely transported even with a cartridge inserted.
• When the cap is placed onto the tool, the cartridge stops heating immediately, data transfer is cut off and the tool is disconnected from the station. It turns off completely after 10 minutes of inactivity. This allows a greater saving of the tool’s battery.
• The stand has a holder for two safety caps on the back. This component can be detached by loosening and removing the screw between the two holders (1).
• While the tool is being used, the cap can be stored on the cap holder.

Operation

The JBC Most Efficient Soldering System
This revolutionary technology can recover tip temperature extremely quickly. This allows the user to work at a lower temperature.

Work

• When the tool is lifted from the tool holder, the tip of the assembled cartridge will heat up to the selected working temperature.

Charge Mode

• While the tool remains on the tool holder, it charges and the tip will gradually cool down to room temperature.

Sleep Mode

• If Sleep Mode is activated (see section “Settings”), upon placing the tool on its holder, besides charging it enters Sleep Mode. The tip temperature will drop down and remain at Sleep temperature.

Hibernation Mode

• When the tool is away from the tool holder and remains inactive (no movement for at least 10 seconds), the tool goes into Hibernation Mode and the tip temperature gradually cools down to room temperature.

Automatic Turn Off

• If the tool has been inactive for a longer time (at least 5 minutes), it automatically turns off.

Turning the Tool Back On

• After automatically turning off, put the tool back on the tool holder to turn it on again.

NOTE: The tool can also be switched off/on manually. Tap the Tool power switch on the display (bottom right) to switch it off/ on (if the tool is turned off, it will remain connected up to 5 minutes to the station but will not heat up the cartridge).

Work Screen
The Work screen shows a graph of the tip temperature and power supplied to the tip updated in real time. It allows to modify the tool working temperature, check the battery status and turn on and off the tool in use.

Graph and Automatic Data Display
The graph display of the temperature and supplied power starts automatically as soon as the tool is lifted from the charging base.
The graph display can be paused while working by tapping the screen on the graph area. While the automatic display is on hold, the temperature/power values can be checked at a certain point of the graph by tapping on the desired position on the display screen.
Note: Pausing the automatic display by tapping on the screen does not stop the tool from heating up, and the tip will remain at the selected working temperature.
The graph can be moved to the left and right by swiping the touch screen sideways with one finger.

Working Temperature Modification
The working temperature can be modified using the slider below the graph (± 5 ºC / ± 10 ºF).

Work Screen

Stopping Data Display
When the tool is placed on the tool holder or when it enters Hibernation Mode, the data display stops.
The display starts again automatically when the tool is lifted from the tool holder and the graph is automatically displayed again at the point where the previous display stopped, leaving a small gap on the graph between the last registered value and the new starting point.
Working with Two Tools
When working with two tools, to switch between the two graphs, tap on the tool selector (upper-right corner of the display) and select the desired tool from the drop-down menu.
It is also possible to alternate both graphs by simply lifting one tool or the other from the tool holder.
The display will automatically show the graph and information of the tool in use.
Note: All menu items are explained in detail starting at section “Menu”.

Cartridge Exchanger

The cartridge exchanger saves time and allows to change cartridges safely without switching the tool off.

Removing Cartridges

• Place the cartridge over one of the slots of the cartridge exchanger and press down (1) until you hear a click. Then pull the handle out (2) to remove the cartridge.

Inserting Cartridges

• Place the handle over a cartridge and press the handle down to insert the cartridge.

Cartridge Retention

• Cartridges are held in place inside the cartridge exchanger thanks to the retention clamps, with the advantage that the cartridges do not fall into the exchanger and the cartridge tips are therefore protected. The cartridge exchanger of B·IRON stations works with C210 and C115 cartridges.

C210 Cartridge Retention Area

• The holding area of C210 cartridges goes from the start of the tip until the cartridge begins to widen.

C115 Cartridge Retention Area

• The holding area of C115 cartridges is delimited by the two rings before the tip.

Fixing Cartridges

Depending on the shape of the tip, use the holes on the sides of the cartridge exchanger to properly adjust the cartridge.
Important: Push the cartridge in as far as it will go, making sure that it is firmly assembled*.

Inserting C210 Cartridges

• Push the cartridges inside the handle until the reference mark is aligned with the edge of the handle.

Inserting C115 Cartridges

• Push the cartridges inside the handle until the reference ring rests against the sealing plug.

Cartridge Holder for C210 Cartridges

• The cartridge holder (4x slots) is used to store cartridges. It allows to have different cartridges quickly at hand and it works with C210 Cartridges.

Cartridge Adapters for C115 Cartridges

• Since C115 cartridges have a smaller diameter than C210 cartridges, adapters must be used to store them in the cartridge holder. These adapters must simply be inserted from above into the slots of the cartridge holder.

Tip Cleaner

• Select the option that best suits your needs and improve the tip thermal transfer.

Wiper

Tapping

• Tap gently to remove excess solder.

Wiping

• Use the slots to remove the remaining particles.

Replacing Brass Wool

Lifting

• Lift the wiper by using the recess on the edge.

Replacing

• Remove the wiper and replace the brass wool with a new one.

Reassembling

• Assemble the new wiper onto the charging base.
• Make sure that the brass wool is on the far left and that there is space for the wiper on the right.

Pressing on

• Press the wiper down at the 4 corners until you feel it click into place. Make sure that the wiper membrane is inserted correctly all the way around.

Note: The brass wool and the wiper positions can be reversed by rotating the antisplash membrane 180 degrees.

Replacing Grips

Cutting

• Make a length-ways cut on the worn grip.
• Be careful not to damage the handle.

Removing

• Remove the worn grip.

Assembling New Grips

Replacing Sealing Plugs

The sealing plug prevents undesirable flux vapours or particles from entering the handle. Its usage is highly recommended for intensive applications when soldering is exposed to FOD environments or for applications where the soldering iron works close to a vertical position.
Note: Choose the correct sealing plug depending on your handle model.
Before replacing the sealing plug, disconnect the tool from the station and make sure the device is not hot.

Removing Sealing Plug

• Introduce a small shaft or screwdriver, not deeper than 8 mm, lift and pull the sealing plug. Never use a cartridge to do this operation.

Mounting Position

Note: The chamfered side has to be positioned towards the handle.

Inserting Sealing Plug

• Push the sealing plug inside the handle until the sealing plug and handle edges are aligned.

Tool Holder Dissasembly and Replacement

• Adjustable tool holders can be disassembled by loosening the screws (1) at the bottom of the charging base and pulling downward from the side band (2). Before sliding down the side band, hold the tool holder with your hand to prevent it from falling down.
• Then, to install a new tool holder onto the charging stand, place the tool holder at the top of the side rail and slide back the slide band over it until it is secured in place and tighten the screws at the base.
• Find more information about Expansion Kits on www.jbctools.com.

Menu

Menu – No Tools Connected
Before any tool has been connected to the station or after the last tool has been disconnected, the menu offers these options.

Menu – Tool Connected
Once at least a tool has been linked, the menu expands and shows some more options.

Work

• Takes the user to the work screen (see section “Work Screen”).

Settings

• The B·IRON app offers an intuitive user interface, which provides quick access to several station parameters.

Settings

Installing and Updating the B·IRON App

To install or update the app, some kind of internet connection is required (WiFi, cable, mobile data…).

1. Go to the App Store or Play Store (depending on your operating system).
2. Search for JBC B.IRON on the search bar.
3. Tap on the app and then on Obtain / Install / Update.

For Android devices the app installer can also be downloaded from:
https://www.jbctools.com/jbcsoftware.html.

Updating the Firmware

• Download the JBC update file to your PC from: https://www.jbctools.com/software.html.
• Connect the tablet/device via USB connection to the PC.
• Check if there is a folder named “JBC” in the internal storage of the Android device used as B·IRON display. If it doesn’t exist, create it.
• Copy the downloaded file to the JBC folder.
• Access the B·IRON app and, in the Menu, select Update.
• Tap on Select your firmware file and pick the downloaded file from the drop-down menu.
• Tap on Update (1).

Accessories

• B·IRON soldering stations can be accessorized with some additional components specifically designed for them:

Display Holders
JBC offers display holders in two different sizes. Choose the size that best suits your needs and the display size.

B115
High-Precision Handle for B·IRON
This handle is compatible with B·IRON B210 DUAL. To store C115 cartridges on the tool holder it is necessary to purchase C115 Cartridge Adapters (ref. 0030643, sold separately).

BP115K
Expansion Kit for BP115 Tweezers
This kit is fully compatible with B·IRON 210 DUAL. It includes BP115 High- Precision Tweezers with its holder.
BP115K is used to expand the versatility of B·IRON soldering stations.
To get more information about the complete B·IRON range visit www.jbctools.com.

Maintenance

• Before carrying out maintenance, always extract the cartridge from the tool and disconnect the charging stand from the mains. Allow the equipment to cool down.
• Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.
• Periodically check that the metal parts of the tool and tool holder are clean so that the charging works properly.
• Maintain the tip surface clean and tinned prior to storage in order to avoid tip oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint.
• Do not use liquids such as alcohol, thinner or benzene to clean the tablet.
• Repairs should only be performed by a JBC authorized technical service.

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

• Do not use the units for any purpose other than soldering or rework. Incorrect use may cause a fire.
• The power cord must be plugged into approved bases. When unplugging it, hold the plug, not the wire.
• Do not attempt to dismantle or open the housing of the tool as it may cause damage.
• Do not work on electrically live parts.
• The tool should be placed in the stand when not in use in order to charge the batteries.
• The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the station is turned off.
• Do not leave the tool unattended when it is on.
• Avoid flux coming into contact with skin or eyes to prevent irritation.
• Be careful with the fumes produced when soldering.
• Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
• Utmost care must be taken with liquid tin waste, which can cause burns.
• This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved.
• Children must not play with the appliance.
• Maintenance must not be carried out by children unless supervised.
• Do not expose the tablet to high temperatures, humidity or dust. Avoid direct sunlight.
• Do not drop the portable display or the tool, as it may cause damage or malfunction.
• Do not disconnect your device when it is in fi le transfer mode.
• Do not use the portable display in places where wireless communications are restricted.

Safety – Battery

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

• Caution: This product contains lithium-ion batteries. Mishandling or improper use may result in fire, explosion, or personal injury.
• Always use the provided charger. Do not use damaged chargers or batteries.
• Never attempt to disassemble or modify the batteries or the product. Doing so may lead to electric shock, fire, or damage to the product.
• In the event of damage, leakage, or overheating of the batteries, discontinue use immediately and contact customer support or JBC technical service facility.
• Dispose of devices with batteries inside, responsibly according to regulations. They must be disposed of in accordance with local regulations so that they can be recycled.
• Do not throw devices with batteries into household waste and do not dispose of them in fire or water.

Specifications

B·IRON 210 DUAL
Battery-Powered Soldering Station
Ref. BISS-5A

Charging Base

• Input: 100 V – 240 V 50 / 60 Hz
• Nominal Power: 40 W
• Tool Output: 12 V / 1000 mA
• USB Output: 5 V / 1000 mA

B210 Handle

• Peak Power (Tool): 24 W
• Battery: Li-Ion 7.4 V / 540 mAh
• Charge Time: 60 minutes
• Selectable Temperature: 100 – 450 °C / 210 – 840 °F
• Idle Temp. Stability (still air): ±1.5 °C / ±3 °F
• Temp. Accuracy: ±3 % (using reference cartridge)
• Connections: Bluetooth Low Energy (BLE)
• Ambient Operating Temp.: 10 – 50 °C / 50 – 122 °F
• Tool Weight: 75 g / 0.165 lb

Portable Display 7”

• Display Dimensions: 7” / 7 in
• Total Net Weight: 1.94 kg / 4.27 lb
• Total Package Dimensions/Weight: 265 x 223 x 160 mm / 2.82 kg (L x W x H) 10.43 x 8.78 x 6.30 in / 6.22 lb

Complies with CE standards.
Not grounded device. No ESD discharge feature.

Warranty

• JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour.
• Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
• Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase.

This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

www.jbctools.com.

References

• JBC Soldering Stations, Irons and Rework equipment for electronics
• JBC Software
• Warranty Extension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>