CREALITY HALOT-SKY 3D Printer User Manual
- June 4, 2024
- Creality
Table of Contents
Create reality， achieve dreams
HOT-SKY
HOT-SKY
3D Printer User Manual
HALOT-SKY 3D Printer
Dear Consumers,
Thank you for choosing our products. For the best experience, please read the
instructions before operating the Printer. Our teams will always be ready to
render you the best services. Please contact us via the phone number or e-mail
address provided at the end when you encounter any problem with the Printer.
For a better experience in using our product, you can also learn how to use
the printer in the following ways: View the accompanying instructions and
videos in the U disk.
Visit our official website www.creality.com to find
relevant software/hardware information, contact details, and operation, and
maintenance instructions.
Firmware Upgrade
Please login the official website https://www.creality.com/download, switch
the language and select the relevant printer and model and download the
required firmware, you can use it after the installation is finished.
NOTES
-
Do not use the printer any way other than described here in order to avoid personal injury or property damage.
-
Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
-
Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
-
Please use recommended resin to in case damage of the machine.
-
Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
-
Please do not open the plastic cover during usage, otherwise, the printing will be interrupted.
-
Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printer’s moving parts leading to burns, possible bodily injury, or printer damage.
-
Please wait a moment after the print is finished. And please wear gloves to take out the print by tools.
-
Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame,
guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface. -
Children under 10 years should not use the printer without supervision.
-
Tips： Do not plug or unplug the power cord when power on.
-
Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators’ legal liability under any circumstance.
Introduction
1. Limit switch
2. Hexalobular socket screw
3. Leveling screw
4. Building platform
5. Air filter| 6. Hexalobular socket screw
7. Resin vat
8. Touch screen
9 . USB port
10. Power socket
---|---
Equipment parameters
Basic Parameters 4**
Model| HOT-SKY
Software language| English
Print method| U disk I U Online Printing of Creality Cloud
X/Y-axis resolution| 0.05mm I 3840’2400
Z-axis resolution| 0.01mm-0.1mm(layer thickness
Print speed| 1-45/ layer
Special filaments| Common rigid photosensitive resin, Standard resin, Hight
hardness, High toughness, Dental model resin.
Light source configuration| UV integrated lamp bead (wavelength 405nm) I
g414:Mknit(g-K405nm)
Operation system| Windows 7 and above systems, mac systems I window
Nominal power| 250W
Print size| 192120200mm (length”width height)
Machine size| 340292*552mm
Package size| 450’390’705mm
Machine weight| 16.5KG
Gross weight| 22.45KG
Display screen| 5inch I 5A1-
Package Content
Tips: the above accessories are for reference only, in kind prevail!
Assemble the 3D Printer
Interface Information
| 
---|---
Note: The current interface is for reference only, due to the continuous
upgrading of functions, the actual to the official website of the latest firmware
UI as the standard.
5. Interface Information
Setting
Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.
Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.
Level Platform
Note: The printing platform has been leveled at the factory. If it needs leveling due to transportation or other reasons, please follow the steps below to adjust the printing platform.
- To calibrate the printing platform, first raise the platform, loosen the fixing screws on the left and right sides of the material trough, and take out the material trough;
- Loosen the four Leveling screws of the prototyping platform, attach the Calibration card tightly to the print screen, and press Settings → Z Axis Motion → Levelling（Refer to operating steps of leveling platform 2 for operation.）, to check whether the platform fits evenly with the paper.
- After confirming that Calibration card fits evenly with the platform, screw up the four screws of the platform.
Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware UI as the standard.
Load Resin
Pour the UV photosensitive resin into the resin vat. The slot capacity is
500ml/1000ml.
3DUV :500ml/1000ml。
** Tips: Take out the resin vat slowly, pour out the
remaining resin into the container, clean the resin vat, pour in new resin,
and then install the resin vat to the machine.
How to change resin:
Caution:** Resin may cause skin irritation or an allergic skin reaction.
Please wear gloves before use to avoid direct contact with the skin.
Release Film Instructions
Installation steps
a.First,
remove the 14 screws at the bottom of the vat and take down the old release
film.
b. Prepare the new release film, peel off the protective films on both sides of
the release film. Align the holes and fit the release film on the clamping ring.
c. Finally, place the film-ring assembly back into the vat frame gently, then
install and tighten the fixing screws diagonally.
d. The installed release film is as shown.
Start Printing
-
Open the slicing software of the LCD 3D printer, click “open” on the left of the screen and add the model file.
-
If the model needs to add support, click the upper-left icon to set corresponding parameters.
-
Click icon ①→Setting slice printing parameters②→ ”evil“ kill
-
Weht evas→dehsinfi be to evils of initial sliced file You are welcome to find more details of slicing tutorial on the official website www.creality.com).
- Generate cxdlp file， and save the file to U disk.
- Insert the U disk → press the print button.
Control remote printing
Wiring Connections
Troubleshooting
FCC Statement
FCC Caution: Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance 20cm
between the radiator& your body.
Due to the differences between different machine models, the physical objects
and the final images can differ.The final explanation rights shall be reserved
by Shenzhen Creality 3D Technology Co., Ltd.
https://qr.creality.com
Scan To Learn More
SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.
Add:18F, JinXiuHongDu Building, Meilong Blvd., Longhua Dist.,
Shenzhen, China 518131
Official Website:www.creality.com
Tel：+86 755-8523 4565
E-mail:info@creality.com
cs@creality.com
18F：www.cxsw3d.com
：400 6133 882 0755-8523 4565
Documents / Resources
|
CREALITY HALOT-SKY 3D
Printer
[pdf] User Manual
HALOT-SKY 3D Printer, HALOT-SKY, 3D Printer, Printer
---|---
References
- 创想三维(CREALITY) - 3D打印机,教育/工业3D打印机领导品牌
- Reality Simulations, Inc.
- Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator
- 创想三维(CREALITY) - 3D打印机,教育/工业3D打印机领导品牌
- 3D Printer Slicer Software& Firmware Download - Creality 3D
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>