Lepro PR906501-US Motion Activated Floodlight Camera User Manual

Lepro PR906501-US Motion Activated Floodlight Camera User Manual

Package Contents

Model No.: PR906501-US
28 W(Lamp 22W / Camera 6W), 2400 lm, 110-130V ~, 60 Hz, 0.235 A,
CRI>70, PF 0.6, IP65, 5000 K, -25 °C – 40 °C / -13 °F – 113 °F

Introduction

This Floodlight Camera is a sophisticated smart home security system combining advanced PIR motion sensor lighting and real-time video monitoring. It can help monitor and keep an eye on your home day and night. It will alert you the minute someone enters your property, including an intruder, and allows you to talk to them right away.

Notice

• Do not dismantle or replace any parts of the product without professional guidance.
• This manual is meant for informational purposes only. Working with electricity can be dangerous unless you take precautionary safety measures.
• We recommend you consult and hire a licensed electrician.

Installation Guide

RECOMMENDED INSTALLATION HEIGHT: 6.5-8.25 feet above the ground. At a detection angle of 75°, the sensor will provide a maximum sensing range of up to 39 feet.

You can adjust and move the sensor heads up and down, left to right, to the required angle for the desired coverage area.

TOOLS YOU NEED (not included)

Notice
To attain maximum product performance and avoid unnecessary environmental disturbance, please be sure to comply with the following conditions during product installation:

• Do not install the product in close proximity to thermal sources, like air conditioner outdoor unit or kitchen smoke outlet, etc.
• Make sure there are no reflective objects within a 5 feet range of the PIR sensor, which will interfere with the sensor’s normal functioning.
• Do not put the camera directly facing high PF LED light, which will pick up the flickering of the LEDs

CAUTION: PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN

You can install the Floodlight Camera by following the steps below:
Step 1 : Shut the power off at the circuit breaker (NOT THE SWITCH).

Notice

• Please make sure the power voltage is 110-130 V~, 60 Hz.
• Properly ground the fixture.
• Do not connect this light fixture to a dimmer switch or timer.
• Always follow the code standards when installing wired connections.
• Do not install near combustible or flammable surfaces.

Step 2: Install the Mounting Crossbar
Attach the crossbar (A) onto the junction box (not included) using the two long screws (C) included in the package. Ensure that the screw thread on the center hole is pointing away from the surface.

Notice: The Floodlight Camera must be installed on a wall and the UL- listed junction box.

Step 3: Wiring the Floodlight Camera
Remove the paper barrier from the EVA gasket (B) and adhere the gasket to the crossbar and outer edge of the round surface junction box. Ensure that the short screw on the crossbar threads the hole of the EVA gasket(B). Then wire as below:

• Use a wire nut (F) to connect all the white wires. The white wire on Floodlight Camera is neutral.
• Use a wire nut (F) to connect all the black wires. The black wire on Floodlight Camera is a hot wire.
• Connect the ground wire from the junction box to the ground screw (D, green) on the metal crossbar (A).

Step 4: Mounting the Floodlight Camera
Make sure wire connections are secure. Carefully align wires through the junction box. Mount the Floodlight Camera onto the crossbar(A) and fasten with the supplied Nuts(E). DO NOT over-tighten them.

Step 5: Restore power for the test
Restore power at the circuit breaker. The Floodlight Camera will begin speaking to you to let you know it is in setup mode. Now the Floodlight Camera is working!

Last step : Waterproof treatment
After mounting the Floodlight Camera, to ensure it is water-resistant, seal the entire junction box with a silicone sealant to prevent water from leaking in. It is crucial and necessary for wet locations.

Notice
Please do not install the product in a harsh environment. The product may be damaged if exposed to high temperature, high humidity, heavy dust, smoke, etc.

APP Paring

Before you begin, please make sure you have the following minimum requirements:

• Smartphone or tablet running iOS 9.0 or later, or Android 5.0 or later.
• Home WiFi Network (The device support 2.4GHz only, does not support 5G WiFi)
• Internet access with upload speed of at least 2 Mbps.
• Make sure your phone bluetooth function is ON.

Download the App

1. Download and install the “Lepro LampUX” APP from the App Store/Play Store and register to create a new account.

2. Power on the floodlight fixture, the light will switch on for a few seconds. Then wait for around 30 seconds, you will hear short music first, followed by a “beep beep” tone.
   

3. Open the Lepro LampUX APP, tap on the “+” sign, and follow the onscreen steps to select the appropriate “Floodlight Camera” to start the connection from the device list.

4. When you get the prompt for the WiFi connection, enter the username and password and click “next.”
   

5. A QR code will pop up on your screen, which you need to hold up to the camera of the light.

6. When you hear a long beeping tone, click the “I heard a Prompt” button on your phone screen.
   

7. After pairing the phone and camera, rename the light on your APP and then save. Now, you are all ready to go.
   

Note: If this doesn’t work, please reset the product. Long-press the reset button for around 5 seconds until you hear a short audible beeping tone. Then repeat steps 2-7 to pair the APP.

Voice Control

If the light does not work, please go to Amazon Alexa or Google Home APP and click DISCOVER DEVICES.

Examples of Alexa control commands:

• Alexa, show me the “DEVICE NAME”. (Like “Floodlight Camera”)
• Alexa, hide the “DEVICE NAME”.
• Alexa, turn on the “DEVICE NAME”.
• Alexa, turn off the “DEVICE NAME”.

APP Using

Settings

• Basic Function Settings

Talk Modes: One-Way Communication (Hold the talk button to talk), Two-Way Talk (Tap the talk button to start talk)

• Detection Alarm Settings

1. Turn on Motion Detection Alarm and set the Alarm Sensitivity Level.
2. Set up schedules for detection alarm, and whether the siren is enabled when the alarm is on.
3. Alarm photos will be saved in the messages, and alarm video recordings will be saved in the playback. (Make sure to use a TF card or cloud storage service.)

• Storage settings

Storage settings are displayed only when a memory card is inserted.

1. After inserting a new TF card, you need to format it and turn on Local Recording before it can store videos.

2. Local Recording allows you to decide where to store video recordings, card or cloud.

3. Recording Mode allows you to choose Event Recording or Non-Stop Recording.
   If you select Event Recording, make sure the Motion Alert is on, otherwise, you won’t get any recordings.

4. You can set up schedules to start or stop recording.

• Share Devices

You can share the device with other people who have Lepro LampUX accounts.

• FAQ and Feedback

When encountering a problem, you can check out FAQs on the app. If your problem can’t be resolved, please kindly contact us. Email address: cs@lepro.com

Troubleshooting Tips

• Serious stroboscopic picture showing in live view. It is mainly caused by different AC frequencies, which you can solve by changing the AC frequency in the App settings-Picture/View.
• Device is offline in the device list? Check the quality of the device network and see if it is good or not. If you already inserted a TF card, please unplug the TF card, and reset the device and router. Check whether the device is online or not. If the problem still exists, please reset the device and pair it to the APP again. After that, check the device firmware and App version and upgrade them to the latest updated version.
• What to do if the device is offline after changing a router or WiFi password? Please reset the device and pair it to the APP again.
• Cannot check video playbacks. Remove the TF card, reinsert the card into the slot again and then make sure the recording mode is ON. If there are still no video recordings, please go to “Settings,” click on “Record settings,” disable “Record switch,” and format the TF card. If the problem persists, please try inserting a new TF card.
• The light stays on for a long time after motion is detected. Adjust Light -> Time-Delay Duration to shorten the time.
• Motion detection doesn’t work consistently. Each detection requires about 60s of cooling time, otherwise it won’t be detected.

FCC
Federal Communication Commission (FCC) Statement for Users Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>