IMOU 1.2.98.01.10674 Series Smart Robot Vacuum Cleaner User Manual

User Manual
Smart Robot Vacuum Cleaner Series
V1.1.0

Usage Restrictions

• Plastic bags can be dangerous. Keep them away from infants and children to avoid the risk of suffocation.
• This product is only meant to clean floors in a home environment. Do not use it outdoors (such as in an open balcony), on other non-floor surfaces (such as sofas), or in commercial or industrial settings.
• Do not use the product in a suspended environment (such as duplex buildings, open balconies, or on top of furniture) without guard rails.
• Do not use the product in temperatures higher than 40°C (104 °F) or lower than 0°C (32°F). Do not use the product if there is liquid or viscous substances on the floor.
• Ensure that cables are kept off the floor before using the device to prevent cables from being dragged around when the device is working.
• Keep all fragile and miscellaneous items (such as vases or plastic bags) that are on the floor to avoid obstruction of or collision with the device while it is working, which may result in damage of valuable iterns.
• Do not allow people with impaired physical, sensing or mental abilities, or peaple with insufficient experience and knowledge (including children) to use this product without guidance or supervision.
• Do not allow infants or children to use this product as a toy.
• Do not place the main brush cleaning tool within reach of children.
• Do not allow any body parts of humans or animals, including hair, fur, fingers, etc. to come close to the vacuum inlet of the device when the device is working.
• Do not use the product to clean flammable objects (such as lit cigarette butts).
• Do not use the device to vacuum hard or sharp objects (such as waste materials from renovation, glass, or nails).
• Do not use the cover of the laser range sensor, the top cover of the device, or the collision buffer device as carry handles for transporting the robot.
• Before cleaning and maintaining the device and the charging dock, turn the device off and unplug it from the socket to disconnect the power supply. Do not submerge the device or the charging dock in water or rinse ther with water to clean them.
• Do not use a wet cloth or any liquid to wipe any part of this product.
• Do not use the mop module in a carpeted environment.
• Follow the instructions in the manual when using this product. The user is responsible for any loss or damage caused by improper use.

Battery and Charging

• Burning the device is prohibited even if the product has been severely damaged, as doing so may cause explosions.

• Do not use any third-party batteries, chargers, or charging docks.

• Do not disassemble, repair, or modify batteries and charging docks.

• Do not place charging docks near heat sources, such as radiators.

• Do not wipe or clean the charging dock clips with a damp cloth or wet hands.

• Do not dispose of batteries with your regular trash. Batteries should be disposed of by professional recycling agencies.

• If the power cord is damaged, it must be replaced by professionals from the manufacturer, the manufacturer’s service department, or a similar department to avoid danger.

• If the product must be transported, ensure the device is turned off,
  It is recommended that you use the original box packaging to transport the product.

• Do not pour water into the device or submerge it in water.

• If you are not using the device for a while, charge it fully, turn off the device, and place it in a cool, dry area. Charge the device at least once every three months to avoid damage to the battery.

• Use proper toals when removing the battery. First, remove the screws from the bottom cover. Then, open the bottom cover and unplug the battery from the terminal. Finally, remove the battery from the battery holder.

• The battery must be removed from the device before discarding the device.

• The device must be powered off before removing the battery.

Class 1 laser product. The laser radar in this product conforms to the GB 7247.1-201 2/IEC 60825-1:2014 safety standards for Class 1 lasers, and will not produce laser radiation harmful ta the human body.

Package Contents

Diagrams of products, accessories, user interfaces, and other items in the manual are schematic diagrams and are for reference only. The actual product may differ slightly from diagrams in the manual due to product updates and upgrades. The actual product  shall prevail in case of any discrepancies. Accessories installed on the robot vacuum cleaner![IMOU 1.2.98.01.10674 Series Smart Robot Vacuum Cleaner

• Content 1](https://manuals.plus/wp- content/uploads/2024/01/IMOU-1.2.98.01.10674-Series-Smart-Robot-Vacuum- Cleaner-Content-1.jpg)

Product Overview

1. Device

![IMOU 1.2.98.01.10674 Series Smart Robot Vacuum Cleaner

• Product 1 1](https://manuals.plus/wp- content/uploads/2024/01/IMOU-1.2.98.01.10674-Series-Smart-Robot-Vacuum- Cleaner-Product-1-1.jpg)

Installation and Use

1. Remove the limit bar
   Place the robot vacuum cleaner on flat ground indoors.
   Remove the limit bar from both ends of the front bumper.

2. Install he charging dock
   • Place the charging dock on flat ground against the wall. Insert the power plug into a socket that meets the requirements and turn on the power.
   • Ensure that there are no obstacles within 1.2m in front of the charging dock and within 0.5m on both sides of the charging dock.Charging the device
   Press and hold the button for 3 seconds to start the robot vacuum cleaner. Then, press the button to recall the robot vacuum cleaner to the dock for charging. The robot vacuum cleaner will enter standby mode after it is fully charged.

• Charge the robot vacuum cleaner fully before cleaning.
• Before cleaning, ensure that cables and items on the ground are properly organized, to prevent them from being tangled, dragged or bumped into during cleaning, resulting in damage.
• It is recommended that you enable the robot vacuum cleaner to start cleaning out of the charging dock. This can facilitate a rapid recharge of the cleaner.
• If there is insufficient power during cleaning, the robot vacuum cleaner will automatically return to the charging dock for charging. It will return to the last-cleaned position to resume cleaning after charging is completed.

Installation and Use/Cleaning

The Auto cleaning mode is set by default. After the device is connected to the app, more modes are available.

1. Cleaning
   • Press the button to start Auto cleaning;
   • Press and hold the button for 3 seconds to start Spot Cleaning.

2. Pause
   When the robot vacuum cleaner is cleaning, press the or button to pause the cleaning.

3. Waking up
   The robot vacuum cleaner will enter sleep mode if it is stationary for 60 minutes. Press any button to wake the robot when it is in sleep mode.

4. Automatic recharge/manual recharge
   • The robot vacuum cleaner will automatically return to the dock to charge if there is insufficient power while cleaning. The robot vacuum cleaner will also return to the dock to charge after cleaning is completed.
   • When the robot vacuum cleaner is cleaning, press the or button to pause the device, and then press the button to recall the cleaner to the charging dock for charging.

5. Turning off
   When the robot vacuum cleaner is stationary, press and hold the button for 3 seconds to turn the device off. The power indicator light will quickly flash white for five seconds before it turns off,

The robot vacuum cleaner cannot be powered off and cannot enter sleep mode while charging.

Installation and Use/Mopping

1. Remove the two-in-one water tank

2. Install the mop holder

3. Add water
   Purified water’s recommended, To prevent Corrosion on metal comoonents, alease do not use detergent

4. Mopping
   • Press the button to start Auto mopping:
   • Press the button for 3 seconds to start Spot mopping.

Scan the QR code below or search for the “Imou Life’ app in the 0App Store. Then download and install the app. Open the app, click + in the upper right comer of the home page. And follow the instructions to add the device.
Due to app grades and updates, actual operations may differ slightly from the above description. Follow the directions in the Current app to perform the operations.
Resetting Wi-Fi and restoring factory settings
Separate the robot cleaner from the charging dock, and press and hold the and buttons simultaneously for 5 seconds. When the power indicator light flash white to off the device will turn on. Press and hold the button for 3 seconds to turn on the device, Then you will hear the voice prompt”WeFi has been reset’ and the device will be waiting for a networ< connection. Then follow the instructions in the app to add the device.

http://mobile.easy4ipcloud.com/imou/detect.html

Supports only the 2.4 GHz Wii band.

Maintenance

Clean Infrared Lens/Charging Contacts
Wine the infrared lens and charging cortacts with a dry and soft cloth every month.

Clean the main brush
The main brush is a consumable. It is recommended that you clean it once a week and replace it every 6-12 months to ensure effective cleaning.

1. When turning the robot cleaner over, press the catch on the cover of the main brush. Then, remove the main brush cover and the main brush.
   Carefully turning the robot cleaner over will prevent laser radar from unexpected collision damages.

2. Cutentangled hairs and fur on the main brush using the small cleaning knife. Use the cleaning brush on the other end of the cleaning knife to clean the main brush.

3. Replace the main brush and main brush cover. Press to fasten the catch.

Clean/replace the side brush

1. Remove the screws of the side brush with a screwdriver.
   Then, remove the side brush.

2. Replace the side brush after cleaning, or install a new side brush,
   The side brush is a consumable. Itis recommended that you replace it every 3-6 months to ensure effective cleaning.

Clean/sensor
Itis recommended to gently wipe each sensor with a clean and soft dry cloth every week, to ensure that the device functions properly.
Robot Vacuum Cleaner:
Cliff sensor x 4
Charging Contact x 2
Infrared sensor x 3
Wall-following sensor x 1 Battery Maintenance

1. The robot vacuum cleaner has an internal high-perfor- mance lithium-ion battery pack. Keep the device charged on a day-to-day basis to maintain battery performance.
2. If you are not using the device for a while, turn it off before storing it. Charge the device at least once every three months to avoid damage to the battery.

Cleaning the two-in-one water tank

1. Press and hold the two-in-one water tank release button, and pull the water tank out.
2. Pull the dust box catch to open the dust box
3. Remove the filter cartridge.
4. Remove the filter.
5. Use the cleaning brush to clean the filter and any debris on the filter cartridge.
6. Open the dust box and wipe it with a dry cloth. After the cleaning reinstall it. The filter is a consumable. It is recommended that you replace it every 3-6 months using filters purchased from official channels
7. Open the water tank cover and add an appropriate amount of water. Purified water is recommended. To prevent corrosion on metal components, please do not use detergent.
8. Turn the two-in-one water tank upside down, and remove the mop cloth for replacement or cleaning. • Clean the mop cloth on time to maintain the mopping effectiveness,
   •  Remove the mop cloth to clean and dry it before reinstalling it.
   It is forbidden to wash the mop in the two-in-one water tank.
   • Otherwise, the reverse flow of dirty water will clog the filter.
   • Ensure that the dust box is dry and free from water stains after the cleaning to avoid generating a bad odour.
   • Ensure that the filter and the dulter cartridge are dry and free from water stains after the cleaning to avoid generating a bad odour.
   • The mop pad is a consumable. It is recommeded to replace it every three to six weeks.

Troubleshooting

When an abnormality occurs while the device is running, the power indicator light will flash red quickly. There will be voice prompts for some abnormalities. Refer to the table below for possible solutions.
The robot vacuum cleaner will automatically hibernate if there are no operations within 60 minutes of entering sleep mode.

obstacles, or move the device to a flat and open area, and restart it.
Check if the bumpers are stuck.| Collision sensor is stuck.| Clean and remove any foreign debris around the bumpers, or move the device.
Clean the cliff sensor. Then, start the unit after removing it from the danger area.| Cliff sensor is triggered after starting the device.| Remove and clean the cliff sensor. Then, move it to a flat and open area before starting it.
Check if the main brush is stuck.| Main brush is stuck.| Clean the main brush or move the device.
Check if the side brush is stuck.| Side brush is stuck.| Clean the side brush or move the device.
Check if the main wheel is stuck.| Main wheel is stuck.| Clean the main wheel or move the device.
Put back the water tank before restarting the device.| Two-in-one water tank is removed.| Install back the two-in-one water tank and filter while ensuring that they are installed in the right place,
The battery is insufficient. Start recalling the device to the dock for charging.| Battery is insufficient while cleaning.| The battery is insufficient. Charge the device before use.
Fan is abnormal.| Fan is abnormal.| Ensure that the air ducts, filter, and other relevant parts of the device are dry and free from water stains before attempting to turn off and restart the device.
Wipe the wallfollowing sensor on the right side.| Wall-following sensor is abnormal.| Wipe clean the wall-following sensor.
Pressure on the top cover of the laser radar.| Top cover on the radar is stuck.| The laser radar is stuck or under pressure. Move the device to a new position and restart it.
Battery is damaged or has not been properly installed.| Battery is abnormal while charging.| The battery temperature is too high or too low. Wait until the battery temperature is normal before using it.
Unable to turn on.| Battery level is low or ambient ternperature is abnormal.| The battery is insufficient. Charge the device before use. If the ambient temperature is too low (below 0°C) or too high (above 50°C), use the device in ternperatures between 0°C and 40°C.
---|---|---
Unable to charge the device.| 1. The charging dock is not electrified.
2. Dirty charging sensor.
3. Poor contact with the charging sensor.| 1. Ensure that there is power flowing to the power cord of the charging dock.
2. Clean the charging plates of the device and the charging sensor head of the charging dock ona regular basis.
3. Exclude the possibility of poor contact caused by the side brush or other foreign objects. Try manually repositioning the device.
Unable to return to charging dock to charge. Unable to locate the charging dock.| The charging dock is blocked or too far away.| Place the charging dock in an open space. Place the device near the charging dock and try again.
Errors occur while cleaning.| The main/side brush, or the main brush is entangled with foreign objects.| Turn the device off before cleaning it.
Decreased cleaning ability or dust falling out of the device.| The dust box is full, the filter is blocked, or the main brush is entangled.| Clean the dust box, filter, and main brush in a timely manner.
Unavailable scheduled cleaning mode.| The battery is insufficient.| The device will start the scheduled cleaning mode only when the remaining battery is more than 15%. So, keep the device charged all day.
Unable to connect to the app.| The W-Fi network is abnormal, the Wi-Fi password is wrong, or the app is abnormal.| Ensure that the device is in an area with good Wi-Fi coverage. Re-enter the Wi-Fi password or reset the robot. Update the app and try again.
No or little water discharged from the mop module,| The water tank is out of water, the mop cloth is too dirty, or the mop holder is not installed in the right place.| Check if there is water in the tank. Wash the mop cloth. Install the mop cloth correctly according to the manuals. Check if the drain hole is clogged with foreign objects and pay attention to adding clean water without impurities.
Too much water discharged from the mop module.| The cover of the water tank is not put in place or the water discharge is set to maximum.| Ensure that the cover of the water tank is installed in the right place. Adjust the right amount of water in the app. Fill the water tank and let it sit for a while to check if there is any breakage or leakage.

Where there is an anomaly with the charging dock, the three types of indicator lights on the dock will simultaneously light up and remain lit. There will also be a notification on the app. Refer to the table below for possible solutions.

Insufficient battery during cleaning; device recharged but does not resume cleaning.| The device is in“Do Not Disturb” mode or manually recharged to end the cleaning cycle.| Check on the app to ensure that the device is not in “Do Not Disturb” mode. Scanning will not resume in this mode. The robot will not resume scanning if you manually charge the unit or manually place the unit back in the charging dock.
Does not return to the charging dock after area cleaning or after being moved.| The device regenerates the map or the charging dock is too far away.| The device will regenerate the map after area cleaning or being removed far away. If the charging dock is too far away, the device may not be able to automatically return to the dock for charging, and you need to manually put the device back to the dock for charging.

@imouglobal
https://en.imoulife.com
service.global@imoulife.com 

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>