Lenco CR-550 Stereo Clock Radio User Manual

: June 4, 2024
: Lenco

Lenco CR-550 Stereo Clock Radio

CAUTION:
Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This unit should not be adjusted or repaired by anyone except qualified service personnel.

PRECAUTIONS BEFORE USE

KEEP THESE INSTRUCTIONS IN MIND:

Do not use this device near water.
Clean only with a slightly damp cloth.
Do not cover or block any ventilation openings. When placing the device on a shelf, leave 5 cm (2”) free space around the whole device.
Install in accordance with the supplied user manual.
Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the cable’s exit point. Do not place heavy items on the power adaptor, which may damage it. Keep the entire device out of children’s reach! When playing with the power cable, they can seriously injure themselves.
Unplug this device during lightning storms or when unused for a long period.
Keep the device away from heat sources such as radiators, heaters, stoves, candles and other heat-generating products.
Avoid using the device near strong magnetic fields.
Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart the device following the instruction manual. During file transmission, please handle with care and operate in a static-free environment.
Warning! Never insert an object into the product through the vents or openings. High voltage flows through the product and inserting an object can cause electric shock and/or short circuit internal parts. For the same reason, do not spill water or liquid on the product.
Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.
Do not use this device when condensation may occur.
Although this device is manufactured with the utmost care and checked several times before leaving the factory, it is still possible that problems may occur, as with all electrical appliances. If you notice smoke, an excessive build-up of heat or any other unexpected phenomena, you should disconnect the plug from the main power socket immediately.
This device must be well ventilated at all time!
This device must operate on a power source as specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company.
The socket outlet must be installed near the equipment and must be easily accessible.
Do not overload ac outlets or extension cords. Overloading can cause fire or electric shock.
Devices with class 1 construction should be connected to a main socket outlet with a protective earthed connection.
Devices with class 2 construction do not require an earthed connection.
Keep away from rodents. Rodents enjoy biting on power cords.
Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord. This can cause a short circuit.
Avoid placing the device on any surfaces that may be subject to vibrations or shocks.
To protect the device during a thunderstorm, unplug the ac power adaptor.
When the device is not in use for long periods, unplug the ac power adaptor for safety reasons.
To clean the device, use a soft dry cloth. Do not use solvents or petrol based fluids. To remove severe stains, you may use a damp cloth with dilute detergent.
The supplier is not responsible for damage or lost data caused by malfunction, misuse, modification of the device or battery replacement.
Do not interrupt the connection when the device is formatting or transferring files. Otherwise, data may be corrupted or lost.
The usb memory stick should be plugged into the unit directly. Don’t use an usb extension cable because it can cause interference resulting in failing of data.
The apparatus shall not be exposed to dripping or splashing and make sure that no objects filled with liquids, such as vases, are placed on or near the apparatus.
To completely disconnect the power input, the mains plug of the apparatus shall be disconnected from the mains, as the disconnect device is the mains plug of apparatus.
The mains plug of the apparatus should not be obstructed or should be easily accessed during intended use.
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Minimum distance of 10cm around the apparatus is needed for sufficient ventilations.
The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table-cloths, curtains etc.
No naked flame sources such as lighted candles should be placed on the apparatus.
Attention should be drawn to the environmental aspects of battery disposal.
The apparatus can only be used in moderate extremely cold or climates warm environments should be avoided.
The rating label has been marked on the bottom panel of the apparatus.
This device is not intended for use by people (including children) with physical, sensory or mental disabilities, or a lack of experience and knowledge, unless they’re under supervision or have received instructions about the correct use of the device by the person who is responsible for their safety.
This product is intended for household use only and not for commercial or industrial use.
Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.
Never remove the casing of this apparatus.
Never place this apparatus on other electrical equipment.
Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or vibration.
Do not clean this product with water or other liquids.
Do not block or cover the slots and holes in the product.
Do not push foreign objects into the slots or holes in the product.
Do not allow children access to plastic bags.
Please check that the voltage on the type plate of your appliance corresponds with your house electricity supply (type plate is located on the back of the unit).
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or the plug, when liquid has been spilled or objects have fallen into the apparatus, when the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or electric shock. Warning: prolonged exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss.

INSTALLATION

Unpack all parts and remove protective material.
Do not connect the unit to the mains before checking the mains voltage and before all other connections have been made.
Do not cover any vents and make sure that there is a space of several centimeters around the unit for ventilation.

Overview

TOP PANEL

CLOCK/MEM Button.
Clock set/Memory
DIM Button.
Select the dimmer level(middle-low-high)
HOUR/SKIP- Button.
Hour set and Frequency -/Storage stations-
MIN/Skip+ Button.
Minute set and Frequency +/Storage stations
SNOOZE SLEEP Button.
AL1/VOL- Button.
Alarm 1 set/Volume down
AL2/VOL+ Button.
Alarm 2 set/Volume up.
FUNC AUTO-SCAN Button.
AL.OFF POWER Button.
QI

REAR PANEL

DC Jack.
Battery Door
USB charge port
AUX IN Jack
FM wire antenna

FRONT CONTROL

LED display.

SET TIME/YEAR/MONTH/DAY

Power on the unit, the display will blinking, now into the TIME SET mode, press [HOUR/SKIP-] button to set the hour, press [MIN/SKIP+] button to set the minutes, press [CLOCK/MEM.] button confirm the time set then into the YEAR SET mode (year range: 2017-2099), press [HOUR/SKIP-] button decrease the year, press MIN/SKIP+] button increase the year, press [CLOCK/MEM.] button confirm the year set then into the MONTH/DAY SET mode, press [HOUR/SKIP-] button increase the month and press [MIN/SKIP+] button increase the day, press [CLOCK/MEM.] button confirm the month/day set then exit the time set mode. The unit will auto-exit the set mode if you not press any buttons for 5 seconds
Under standby mode, press and hold [CLOCK/MEM.] button for 2-3 seconds, the LED will start blinking, the unit enters time set mode. Setting method same as above

ALARM SET

Under standby mode, press and hold [AL.1/VOL-] button, the “AL.1-BUZZ” indicator and time will blinking, the default alarm time is 08:00AM, press [HOUR/SKIP-] button adjust the hour, press [MIN/SKIP+] button adjust the minute, press [AL.1/VOL-] button confirm the set then into the repeat date set, press [HOUR/SKIP-] button and [MIN/SKIP+] button can select “WEEK 1-7”, “WEEK 1-5”, “WEEK 6-7”, press [AL.1/VOL-] button confirm the date set then into volume set, press [HOUR/SKIP-] button and [MIN/SKIP+] button can select “0-16” volume levels (the default volume is 10 level), press [AL.1/VOL-] button confirm the volume set then exit the set mode, the alarm will be activated when time out.
Remark: Can only have the volume set when alarm the radio, no volume set when alarm BUZZ, the volume can’t gradually increase when alarm BUZZ, but volume can gradually increase from 0 level to the set volume level when alarm radio
Under standby mode, press [AL.1/VOL-] button can select BUZZER→RADIO→ALM OFF. If you not press the [AL.1/VOL-] button for 5 seconds, the unit will auto confirm the alarm and exit the set mode
When the alarm is activated, if not press any buttons, the alarm will auto-stop after continued for 1 hour, press [AL. OFF/POWER] button can turn off the alarm. The related indicator will blinking when the alarm is activated
Alarm 2 set same as Alarm 1

SNOOZE FUNCTION

When alarm is activated, press [SNOOZE/SLEEP] button into snooze mode, the alarm will be activated again after 9 minutes, continued for 60 minutes, press [AL. OFF/POWER] button to turn off the alarm

RADIO MODE

Press [AL. OFF/POWER] button turn on the unit, the “FM” is the default mode
Manual searching: short press [HOUR/SKIP-] button or [MIN/SKIP+] button can manual adjust the FM stations
Auto-searching: press and hold the [HOUR/SKIP-] button or [MIN/SKIP+] button can auto adjust the FM stations
Memory obtain the stations: short press [CLOCK/MEM.] button to callout the pre-set station, the display will show “P01”, press [CLOCK/MEM.] button again can callout the next pre-set station, also you can press [HOUR/SKIP-] button or [MIN/SKIP+] button select the pre-set stations. The display will show station frequency 5 seconds later, will exit the time display if not press any buttons for 5 seconds
Storage the stations: select the station which you need stored, press and hold [CLOCK/MEM.] button for 2-3 seconds, “P01” on LED display will blinking, press [HOUR/SKIP-] button or [MIN/SKIP+] button to select the stored position, press [CLOCK/MEM.] button to confirm

AUTO POWER OFF

Under power on mode, press [SNOOZE/SLEEP] button, LED will show “10”, you can continued press [SNOOZE/SLEEP] button to select sleep time from
“10→20→30→40→50→60→70→80→90→OFF”, 5 seconds after you set the sleep time, will auto confirm the set and activate the AUTO POWER OFF function. If you need power off midway, press the [AL. OFF/POWER] button; check or change the auto power off time, after activate the auto power off function, press [SNOOZE/SLEEP] button again, the LED will show the rest auto power off time, press [SNOOZE/SLEEP] button again can select the next level auto power off time (Such as: if originally you set “30”, after 2 minutes, you check the LED will show the rest 28 minutes, if you press [SNOOZE/SLEEP] button again, at this time, the auto power off time will become “40”). If you need turn off the auto power off function, repeat press [SNOOZE/SLEEP] button, until the LED show “OFF”

VOLUME CONTROL

Press [AL.1/VOL-] button or [AL2/VOL+] button adjust to your desired volume, the volume have total “0-16” levels, the default volume is 10 level

TIME BACKUP

Install 2pcs AAA 1, 5V batteries. In case of power failure the clock time will continue. If no backup batteries are inserted the time will recover to a blinking “12:00” or “0:00”after power failure.

AUX MODE

Press the ‘func’ button to change to AUX mode. [FUNC.] button into AUX mode, connect up the external sound, the unit will play music, you can press [VOL-] button or [VOL+] button to the desired volume

DIMMER FUNCTION

You can press the [DIM] button to select the dimmer level from “middle-low- high” level, the default dimmer is high level

USB CHARGING FUNCTION

The USB port can only be used for charging, USB output: 5V, 1A maximum

WIRELESS CHARGING FUNCTION

When a QI compatible device is put on the QI logo on top of the clock radio, the indicator “CHARG” of the clock display will be lit. the indicator will be off when no device is charged.

The specification presents only as a reference. The value of weight and size are approximation.
Our product is improved ceaselessly and the specification and function may be changed without prior notice.

Power supply adaptor (For EU only)

Manufacturer: SHENZHENSHI ENGINE ELECTRONIC CO.,LTD
Model number: EE-0502000DPE
Use only the power supply listed in the user instructions

Guarantee

Lenco oﬀers service and warranty in accordance to European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a none oﬃcial service center in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be void.

Disclaimer

Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, speciﬁcations and pictures in this documentation may diﬀer slightly from your particular situation. All items described in this guide for illustration purposes only and may not apply to a particular situation. No legal right or entitlements may be obtained from the description made in this manual.

Disposal of the Old Device

This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).

Service

For more information and helpdesk support, please visit www.lenco.com Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands