beurer MP 48 UV LED Nail Dryer Instruction Manual

beurer MP 48 UV LED Nail Dryer

Product Information

Specifications

• Model: MP 48
• Size: L 18.9cm x W 16.5cm x H 7.6cm
• Weight: Approximately 330g
• Power Supply : 100-240V~, 50-60Hz
• Wavelength : 365 – 395 nm
• Output: 24V, 1A, 24W

Product Usage Instructions

Included in delivery

Check that the delivery has not been tampered with and make sure that all components are present. Before use, ensure that there is no visible damage to the device or accessories and that all packaging material has been removed. If you have any doubts, do not use the device and contact your retailer or the specified Customer Service address.

• 1 x MP 48 UV/LED nail dryer
• 1 x Mains adapter
• 1 x Instructions for use

Signs and symbols

The following symbols are used in these instructions for use, on the packaging, and on the type plate for the device:

• Warning instruction indicating a risk of injury or damage to health –

WARNING

Getting to know your device
The MP 48 UV/LED nail dryer is a device designed to dry and cure UV/LED nail polish. It comes with the following components:

• 1 Netzadapter (Mains adapter)

• 2 EIN-/AUS-Taste mit drei Timer-Stufen (30, 60 und 120
  Sekunden) (ON/OFF button with three timer settings – 30, 60, and 120 seconds)

• 5 Steckerbuchse (Plug socket)

Intended use
The MP 48 UV/LED nail dryer is intended for drying and curing UV/LED nail polish. It should only be used as described in the instructions for use.

Warnings and safety notes

Read these instructions for use carefully and keep them for later use. Be sure to make them accessible to other users and observe the information they contain. Additionally, take note of the following warnings and safety precautions:

• Keep the device away from children and packaging material to prevent choking hazards.
• Avoid exposing the device to water, moisture, and direct sunlight.

Unit description
The MP 48 UV/LED nail dryer is compact and lightweight. It is equipped with a safety transformer to prevent short circuits. The device has a power button with three timer settings.

Initial use
Before using the MP 48 UV/LED nail dryer, plug the mains adapter into a suitable power outlet that matches the technical specifications indicated on the adapter.

Usage
To use the MP 48 UV/LED nail dryer

1. Apply UV/LED nail polish to your nails.
2. Press the power button to turn on the device.
3. Select the desired timer setting (30, 60, or 120 seconds) by pressing the power button repeatedly.
4. Place your nails under the device’s light source and wait for the selected time to complete.
5. The device will automatically turn off after the set time has elapsed.

Cleaning and maintenance
Regularly clean the MP 48 UV/LED nail dryer to ensure optimal performance. Follow these steps

1. Unplug the device and let it cool down.
2. Use a soft, lint-free cloth to wipe the exterior of the device.
3. Do not use abrasive cleaners or solvents.

What if there are problems?
If you encounter any issues with the MP 48 UV/LED nail dryer, refer to the following troubleshooting steps:

• If the drying time is too short, check if the correct timer setting is selected.

Disposal
Dispose of the MP 48 UV/LED nail dryer in accordance with local regulations for electronic waste disposal. Do not dispose of it with regular household waste.

Technical specifications

• Model : MP 48
• Size : L 18.9cm x W 16.5cm x H 7.6cm
• Weight: Approximately 330g
• Power Supply: 100-240V~, 50-60Hz
• Wavelength : 365 – 395 nm
• Output: 24V, 1A, 24W

Warranty / Service
For warranty and service information, refer to the warranty card
or contact the specified Customer Service address.

FAQ

Q: What is the intended use of the MP 48 UV/LED nail dryer?
The MP 48 UV/LED nail dryer is intended for drying and curing UV/LED nail polish.
Q: How do I clean the MP 48 UV/LED nail dryer?
To clean the MP 48 UV/LED nail dryer, unplug it and let it cool down. Use a soft, lint-free cloth to wipe the exterior of the device. Avoid using abrasive cleaners or solvents.
Q: What should I do if the drying time is too short?
If the drying time is too short, check if the correct timer setting (30, 60, or 120 seconds) is selected.

Included in delivery

Check that the delivery has not been tampered with and make sure that all components are present. Before use, ensure that there is no visible damage to the device or accessories and that all packaging material has been removed. If you have any doubts, do not use the device and contact your retailer or the specified Customer Service address.

• 1 x MP 48 UV/LED nail dryer
• 1 x Mains adapter
• 1 x Instructions for use

Signs and symbols

The following symbols are used in these instructions for use, on the packaging and on the type plate for the device

Getting to know your device

The MP 48 UV nail dryer is intended for artificial nail modeling using UV or LED nail gel. It can be used to apply artificial nails to fingernails or toenails.
The special tunnel-like structure of the device reliably ensures that the nail coating sets evenly. You can define the application duration depending on the type of nail gel using the built-in timer function (30, 60 or 120 seconds).

Intended use
Use the device exclusively on human nails for setting UV or LED nail gels. The device is only intended for the purpose described in these instructions for use. The manufacturer is not liable for damage resulting from improper or careless use. The device is intended for domestic use only, not for commercial purposes.

Warnings and safety notes

WARNING
Important safety notes
Before using the device, read the safety notes through carefully.

Non-observance of the following information may result in personal injury or material damage. Store these instructions for use and make them accessible to other users. Make sure you include these instructions for use when handing over the device to third parties.

• Do not use the device if you have been diagnosed with skin cancer, suffer from unusual discoloration of the skin, take medicines which increase sensitivity to light or suffer from an illness which increases your sensitivity to light.
• Store the device out of the reach of children. The device is not suitable for children under 14 years.
• Keep packaging material away from children to avoid danger of suffocation.
• Do not place or store the device in a location in which it is able to fall or be pushed into a bath, sink or other container containing water. Do not place the device in water or allow it to fall into water or any oth-er liquid. This can lead to a severe electric shock. Never reach for a device that has been submerged in water. Disconnect the mains adapter immediately.
• Never look directly at the UV/LED light.
• Do not use the device during pregnancy.
• Overexposure to UV radiation may cause sunburn to the skin. Too frequent exposure to UV radiation may lead to skin changes and increases the risk of skin cancer.
• Excessive exposure to UV radiation can cause damage to the skin and eyes. Please seek medical assis-tance if you notice any changes to your skin.
• If you are aware of any allergy to UV/LED radiation, consult your doctor before using the device.
• Keep sensitive areas of skin such as scars and tattoos away from radiation.
• Never pull the mains adapter out of the socket using the mains cable or with wet hands.

IMPORTANT

• Never place any objects on the device. Do not cover the device while it is in operation.
• Protect the device from impacts, humidity, dirt, chemicals, marked temperature fluctuations and direct sunlight.
• Make sure that the side air vents of the device are not covered.
• Repairs must only be carried out by Customer Services or authorised suppliers. Failure to comply will in-validate the warranty.
• Never use the device near open flames or hot surfaces.
• Do not use the device if it is visibly damaged, does not function properly or if the mains plug or mains adapter is damaged. In these cases, contact Customer Services.

Unit description

1. Mains adapter
2. ON/OFF button with three timer levels (30, 60 and 120 seconds)
3. Side air vents
4. Fan
5. Female connector

Initial use

Note

• Check to ensure that the package contains all the parts that should be included in the delivery. If any parts are missing or damaged, contact Customer Services.
• Remove all packaging material.

WARNING
Keep packaging material away from children to avoid danger of suffocation.

Usage

1. Place the device on a firm, level and dry surface. Ensure that the fan on the bottom and the side air vents are NOT covered!

2. Insert the mains adapter into a suitable socket according to the technical data on the mains adapter.

3. Insert your hand/foot with the nails treated with UV/LED nail gel into the opening of the device (with the nails facing upwards).

4. Press the ON/OFF button to switch on the nail dryer.

5. Select the desired application duration (30, 60 or 120 seconds) using the ON/ OFF button. Set the application duration according to the recommended setting time of the UV/LED nail gel manufacturer. The device then switches off automatically after the programmed setting time has been reached. Dry your treated nails on the other hand/foot as described in this chapter.
   Press the ON/OFF button once| Application duration = 30 seconds ON/OFF button lights up blue
   ---|---
   Press the ON/OFF button twice| Application duration = 60 seconds ON/OFF button lights up green
   Press the ON/OFF button 3 times| Application duration = 120 seconds ON/OFF button lights up red
   Press the ON/OFF button 4 times| The nail dryer turns off

Pull the mains adapter out of the socket after each use. Allow the nail dryer to cool down completely.

Cleaning and maintenance

WARNING
Before beginning cleaning, pull the mains adapter out of the socket!

• Carefully clean the bottom of the device interior with a damp cloth after each use.
• Do not use any cleaning agents or solvents.

What if there are problems?

mains adapter into the socket.Check that the female connector is positioned correctly.
Female connector not inserted.
No voltage at mains socket.| Check your fusebox.
UV/LED nail gel does not set.| Set application duration too short.| Set a longer application duration on the nail dryer. Set the application duration according to the recommended setting time of the UV/LED nail gel manufacturer

Disposal

For environmental reasons, do not dispose of the device in the household waste at the end of its useful life.
Dispose of the device at a suitable local collection or recycling point. Dispose of the device in accordance with EC Directive – WEEE (Waste Electrical and Electronic Equipment).
If you have any questions, please contact the local authorities responsible for waste disposal.

Technical specifications

Output: 24.0 V  1.0 A, 24.0 W

---|---
Average active efficiency| ≥ 87.94 %
Efficiency at low load (10%)| ≥ 81.60 %
No-load power consumption| ≤ 0.09 W

Su bject to technical changes

Warr4anty / service

Beurer GmbH, Söflinger Straße 218, 89077 Ulm, Germany (hereinafter referred to as “Beurer”) provides a warranty for this product, subject to the requirements below and to the extent described as follows.
The warranty conditions below shall not affect the seller’s statutory warranty obligations which ensue from the sales agreement with the buyer.
The warranty shall apply without prejudice to any mandatory statutory provisions on liability.

Beurer guarantees the perfect functionality and completeness of this product.
The worldwide warranty period is 3 years, commencing from the purchase of the new, unused product from the seller.
The warranty only applies to products purchased by the buyer as a consumer and used exclusively for personal purposes in the context of domestic use.
German law shall apply.
During the warranty period, should this product prove to be incomplete or defective in functionality in accordance with the following provisions, Beurer shall carry out a repair or a replacement delivery free of charge, in accordance with these warranty conditions.

If the buyer wishes to make a warranty claim, they should approach their local retailer in the first instance: see the attached “International Service” list of service addresses.
The buyer will then receive further information about the processing of the warranty claim, e.g. where they can send the product and what documentation is required.

A warranty claim shall only be considered if the buyer can provide Beurer, or an authorised Beurer partner, with

• a copy of the invoice/purchase receipt, and
• the original product.

The following are explicitly excluded from this warranty

• deterioration due to normal use or consumption of the product;
• accessories supplied with this product which are worn out or used up through proper use (e.g. batteries, rechargeable batteries, cuffs, seals, electrodes, light sources, attachments and nebuliser accessories);
• products that are used, cleaned, stored or maintained improperly and/or contrary to the provisions of the instructions for use, as well as products that have been opened, repaired or modified by the buyer or by a service centre not authorised by Beurer;
• damage that arises during transport between manufacturer and customer, or between service centre and customer;
• products purchased as seconds or as used goods;
• consequential damage arising from a fault in this product (however, in this case, claims may exist arising from product liability or other compulsory statutory liability provisions).

Repairs or an exchange in full do not extend the warranty period under any circumstances.

• Beurer GmbH
• Söflinger Straße 218
• 89077 Ulm, Germany

www.beurer.com

www.beurer-gesundheitsratgeber.com

www.beurer-healthguide.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>