OKIN REFINED CB2742 Control Box Instructions

June 16, 2024
OKIN REFINED

Issue department: Bedding Division
Product Function instruction
CB.2742
Date: 2017-08-23
Author: Kyle
No: CB2742
Version: 1. 0

CB2742 Function instruction

Function Picture

OKIN REFINED CB2742 Control Box - parts

Process of test

1.1. HEAD
Connect to head actuator,control by remote single:
Click head up button on the remote, head actuator moves out, stop when released
Click head down buttonhead actuator moves in, stop when released
This function takes effect only by pressing the corresponding button on the remote.
1.2. FOOT
Connect to foot actuator,control by remote single:
Click foot up buttonfoot actuator moves outstop when released
Click foot down buttonfoot actuator moves instop when released
This function takes effect only by pressing the corresponding button on the remote.
1.3. Lumbar
Connect to foot actuator,control by remote single:
Click Lumbar up buttonfoot actuator moves outstop when released
Click Lumbar down buttonfoot actuator moves instop when released
This function takes effect only by pressing the corresponding button on the remote.
1.4. Tilt
Connect to foot actuator,control by remote single:
Click Tilt up buttonfoot actuator moves outstop when released
Click Tilt down buttonfoot actuator moves instop when released
This function takes effect only by pressing the corresponding button on the remote.
1.5. Massage
Connect to head & Foot massage,control by remote:
Click head massage + button,head massage strengthens by one level;
Click head massage – button,head massage weakenby one level;
This function takes effect only by pressing the corresponding button on the remote.
1.6. MFP2
Connect to WIFI box or Bluetooth or anyother device
1.7. underbed light
Click button of underbed light, turns on( or turns off ) the underbed light, switch the status once when click once This function takes effect only by pressing the corresponding button on the remote.
1.8. SYNC port
Connect with the same other Control box or Other accessories;
1.9. Power LED & PAIRING LED
Power supply for control box, PAIRING LED of control box is blue, POWER LED is green
1.10. Power
Connect to the 29V DC;
1.11. Pair button
Press and hold the Pair buttonthe Head, Foot actuators will moves to lower position.
1.12. Pair Function
Double click Pair buttonpairing LED turns onthe control box enters into mode of code paring
Press and hold the paring LED of Remote, the backlight of paring LED flashes, the backlight of remote flashes, the remote enters into mode of code paring;
The backlight of paring LED of remote stops flashing, and the paring led of control box turns off, it indicates that the code paring is successful;
If fails, repeat all the processes above;
1.13. MFP1
Connect to slideswitch

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not insta lled and used in accordance with the instructions, may cause harmful interference to radio communications. Howe ver, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Important Note: Radiation Exposure Statement This device has been evaluated to meet general RF exposure requirement. This device can be used in portable exposure condition without restriction.
ISED Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This devic e must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable expo sure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals