Bol com OL188 Photo Laminating Machine User Manual

Photo Laminating Machine
User Manual

Operating Elements

1. Cuttng head
2. Pressing rat with finger protection
3. Functor/OFF switch
4. Indicator elements(LEDs)
5. Lamunator infeed
6. Visual positioning aids in cm(lines,angles,scale)
7. Anti-blocking slider(for clearing jams)
8. Puncher

Operation

Laminator
The laminator can complete hot lamination:
In the case of hot lamination, the lamination foil is adhered together. Select the lamination method according to the material to be laminated.

1. Hot laminating
   1.1 Connect the power cable to an easily accessible, standard electrical socket.
   Caution: Check that the voltage specifications of the unit correspond to that of your power supply network (220 – 240V, 50Hz; or 100 – 120V, 6OHz; etc.).
   1.2 Use the Function/OFF switch on the back of the appliance to switch on: the red display lamp shows.
   1.3 The drive motor for the transport rollers starts up. The correct operating temperature is reached after about 3-5 minutes and the green display lamp shows.
   1.4 Insert the document to be laminated in the pouches so that there is a margin of approx 3-5 mm to the edge of the foil on all sides.
   Caution: Only use foil Intended for hot laminating.
   1.5 Insert the foil containing the document in the laminator’s insertion slot. Insert the ready closed side of the pouch first.
   Note: To prevent the laminating foil from creasing, never insert the open end of the foil pa at in the insertion slot of the lamlnator first. When inserting the foil, observe the instructions or the insertion slot. The laminating process occurs automatically
   Caution. The lamination foil is very hot and soft when ejected following lamination. Therefore, hand’e tts ‘.inated document with due care!
   Note. lo attn end smoothen the laminated product, place a book or similar heavy, flat object on it.
   1.6 When you have corpieted the laminating process, turn the function switch to th e right OFF position and remove the power plug from the power socket. Let the device cool down before packing it away, for example.
   Caution. The device le hat 5cty er laminating! Risk of injury!

2. Cleaning jammed lamination foil
   The device is equpped with an ABS switch (anti-blocking sliding switch) to clear foil jams quickly.
   Proceed as follows if the lamination foil jams
   2.1 Switch the device off: Set the Function/Off switch to OFF.
   2.2 Press the ABS switch tightly
   2.3Hold the laminator firmly and pull the lamination foil together with the document to be laminated out of the laminator’s infeed
   2.4 Loosen the ABS
   2.5 Clean the transport rollers of any deposits and residual adhesive by inserting a folded piece of paper in the laminator infeed.
   Note: If foil jams occur repeatedly or jammed foil cannot be removed from the laminator, please contact our hotline (refer to Guarantee).

Tnmmer

The tnmmer can be used lo cut paper, card, photo paper and lamination foil.

1. The type of cut
   The trimmer is equipped to complete one type of cut:slraight cut,
   1. 1 Note The blades are accommodated in protective housing.

2. Cutting maternal
   2. 1 Place the device on a stable level surface with the cutting head facing up.
   2. 2 Slide the cutting head to one side of the guide rail
   2. 3 Slide the maternal to be cut under the transparent pressing rail at the required position.
   Note
   Observe the permissible quantity of material which may be cut, refer to Chapter “Inten Use or Technical Data”
   Note The visual positioning aids simplify correct alignment of the material to be cut.
   2. 4 Hold the material to be cut firmly with one hand so that it cannot slip when cut. Otherwise, t cut may be inaccurate.
   2.5 complete the cut, press the cutting head down and slide it along the guide rail to the other side refer to Fig.2
   Note To prevent a faulty cutting edge, do not run the cutting head back again but rewove the cut material directly after completing the cut·

Pucher

The pucher can be used to punch paper, card or lamination foil, etc.:
1.1 The Thickness of the punched paper, card or lamination foil, etc. is 0.3MM
1.2 To complete the punch, put the paper/card/foil etc. into the puncher, then press the punching button, refer to Fig. 3

Changing the cutting head
When the blades in the cutting head are damaged or worn, the culling head must be replaced.
3. 1Remove the cutting head from the pressing rail.
3.2Replace the old cutting head with a new one.

Technical Data

LED READY (green)
Special features.| ABS switch (for clearing jams)
No blistering
Automatic shutdown on overheating
Trimmer
Maximum size,| A4
Maximum cutting capacity| 0.3mm(80g paper 3pcs)/80mic+ 100g paper
Puncher
Punching capacity.| 0 3mm(80g paper 3pcs)
Dimensions (WxD x H):| 380140x75mm
Weight| 1.01kg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>