S3177SV Metal Gear HV Digital Servo

Product Information:

Specifications:

• Model Number: 1M23N12738
• Recommended System: 2.4GHz
• Compatibility: S.BUS or S.BUS2 compatible receiver

Product Usage Instructions:

Warning:

Please read and follow these instructions carefully to ensure
safe and proper usage of the product.

1. Do not insert or remove the connector while the power is ON as
   it may cause erroneous recognition and stoppage of the servo.

2. Always check the battery voltage and charge the battery
   quickly, even when using a receiver with BATTERY FAIL SAFE
   function.

3. The servo is not waterproof. Avoid getting it wet as it may
   result in malfunction or short circuit.

4. When using 5 or more servos for large scale models, it is
   recommended to use a separate power supply. You can utilize an
   S.BUS Hub with Cable (2-way/remote battery pack use) for this
   purpose (sold separately).

5. For optimal performance, it is recommended to use a 2.4GHz
   system.

6. Avoid touching the servo while it is operating as it may
   generate a large amount of noise and become impossible to receive,
   which can be extremely dangerous.

7. When installing the servo, ensure that there is enough space
   for proper ventilation to prevent excessive power consumption and
   decrease the life of the motor and battery.

Caution:

Please take note of the following cautions to avoid potential
risks and damages.

1. Do not touch the servo while it is operating as the motor and
   circuits inside may become hot and cause burns.

2. Do not overload the servo with excessive force as it may damage
   the servo.

3. Use attached dampers and eyelets correctly to ensure proper
   installation and avoid damage.

4. The servo should only be used in applications specified by
   Futaba. Futaba will not be responsible for any damages if the servo
   is used in other applications.

Product Connection:

Follow the steps below to connect the servos:

1. Ensure you have an S.BUS or S.BUS2 compatible receiver.

2. Connect the servos from the S.BUS or S.BUS2 port of the
   receiver via S.BUS hubs.

3. If using conventional servos together with S.BUS servos, you
   will need an S.BUS hub and a compatible transmitter/receiver for
   S.BUS channel setup.

S.BUS Channel Setting:

To set the channel at the S.BUS2 servos, follow these steps:

1. Use an S.BUS channel setting tool to configure the channel
   settings.

2. Refer to the instruction manual of the S.BUS channel setting
   tool for the specific method of setting S.BUS servo channels.

FAQ:

Q: Can I use this servo with a conventional receiver?

A: Yes, you can use this servo with a conventional receiver.
However, you will need additional equipment such as an S.BUS hub
and a compatible transmitter/receiver for S.BUS channel setup.

Q: Can I use this servo underwater or in wet conditions?

A: No, the servo does not have a waterproof construction. It
should be kept away from water to avoid malfunction or short
circuit.

Q: Can I use a separate power supply for large scale

models?

A: Yes, when using 5 or more servos for large scale models, it
is recommended to use a separate power supply. You can utilize an
S.BUS Hub with Cable (2-way/remote battery pack use) for this
purpose (sold separately).

1M23N12738

8VDJH3UHFDXWLRQV

WARNING
7XU Q RQWKH SRZHU LQWU DQVPLWWHU UHFHLYHU RUGHU ,QDG GLWLRQ DOZDVFKHFNWKHRSHUDWLRQRI DOOWKHVHU YRVEHIRUHÁLJKW
‘RQRWLQVHU WRUUHPRYHWKHVHU YRFRQQHFWRUZKLOH WKHUHFHLYHU SRZHULV 21Since the S.BUS2 servo switches the operation mode automatically according to the type of signal (S.BUS signal/PWM signal) from the receiver, if the connector is inserted or removed while the power is ON, an S.BUS connected servo will be erroneously recognized and may stop.

&XUUHQWFRQVXPSWLRQ This servo is designed to be used with models which require especially high WRUTXH DQG KLJK VSHHG )RU WKLV UHDVRQ D ODUJH FXUUHQW ÀRZV GXULQJ VHUYR RSeration. Therefore, decide the safe number of uses by paying careful attention to the remaining battery capacity.
3RZHUVXSSO 8VH WKHEDWWHU DV VSHFL¿FDWLRQ 8VH D EDWWHU RU D YROWDJH UHJXODWRU ZLWK DQ
DPSOHPDUJLQ DV WKHSRZHU VXSSO7KHVSHFL¿HG SHUIRUPDQFH FDQQRW EHGLVplayed with a dry cell battery.

‘RQRW OHDYHWKH VHUYRLQ WKHORFNHGVWDWHLeaving the servo in the locked state (state in which enough force is applied that the servo cannot PRYHPDFDXVHVPRNH¿UHDQGGDPDJH

Even if using a receiver with the BATTERY FAIL SAFE function, it may not operate correctly. Therefore always check the battery voltage and charge the battery quickly.

1HYHU FRQQHFW WKH EDWWHU LQ U HYHUVH Reverse connection may FDXVHVPRNH¿UHDQGGDPDJH
‘RQRW H[SRVHWKH VHUYRWR GXVW DQG ZDWHU The servo does not have a waterproof construction. If it gets wet, the servo may not operate or the power supply may short circuit.

When using 5 or more servos for large scale models, use a separate power supply. An S.BUS Hub with Cable (2-way/remote battery pack use) sold separately can be utilized for using a separate power supply in the S.BUS system.
6VWHPXVH For full performance, 2.4GHz system is recommended.

)RUWKHVHUYRZKLFK KDV DPLGGOHFDVH RIDQ DOXPLQXP KHDW VLQNFRQVWUXFWLRQ,QVWDOO WKH VHUYRVR WKDWLW GRHV QRWWRXFK WKHVHUYRFDVHDQGPHWDOSDUWVRIWKHIXVHODJHIt will generate a large amount of noise if touched. It will become impossible to receive and is extremely dangerous.
:KHQ LQVWDOOLQJWKH VHUYRFKHFN 386+52’/,1.$*(WRPDNH VXUHWKHUHLVQRELQGLQJin order to prevent excessive power consumption and decrease the life of the motor and battery.
CAUTION
‘RQRWWRXFKWKHVHU YRFDVHLPPHGLDWHODIWHUVHU YRRSHU DWLRQ You may be burned because the motor and circuits inside the servo become hot.
‘RQRW WXUQWKH VHUYRKRUQZLWK XQUHDVRQDEOHIRUFHThe servo may be damaged.
‘RQRWGLVDVVHPEOHRUPRGLIWKHVHUYRThe servo has a precision construction. Futaba Corp. will not be responsible for any disassembly or PRGL¿FDWLRQRWKHUWKDQWKRVHVSHFL¿HGEXV

3URJUDPPLQJIXQFWLRQ This servo can be connected to a PC by using the CIU-2 USB Adapter sold separately and its various operating characteristics can be changed as a programmable servo by means of dedicated software 6/LQN. 6/LQN is downloadable from a Futaba WEB site. However, channel setting and other operating characteristics settings cannot be made with the existing S.BUS PCLink software. When you use a transmitter with an S.BUS setting function. By connecting a servo to the S.BUS setting connector of the transmitter, a program setup of a servo can be performed on the screen of a transmitter. This servo does not have stop mode function. Therefore becomes as [ hold ] when the input signal of a servo stops. Depending on a setup, a servo carries out vibration. If a servo continues carrying out vibration, it will break, please restore a setup.
6RIWVWDUW ,QRUGHUWRSURWHFWWKHOLQNDJHRQOWKH¿UVWRSHUDWLRQZKHQWKHSRZHULVWXUQHG
RQ PRYHVWKH VHUYRWR WKHVSHFL¿HG SRVLWLRQVORZO :KHQD QHZFRQWURO VLJQDO enters while the soft start is operating, it become normal operation at once.

6HUYR0RXQWLQJ3UHFDXWLRQV@

‘RQRW GURSWKH VHUYR RU H[SRVHLW WR VWURQJ VKRFNVRU YLEUDWLRQVIt will damage with a shock.

Use attached dampers and eyelets correctly. Screw

8VHWKH VHUYRDV DQ DFWXDWRULQ KREE DSSOLFDWLRQV Futaba will not be responsible if the servo is used in applications other than the above.

Rubber grommet Eyelet

Rubber grommet Eyelet
Servo mount

)XWDEDZLOOQRW EHUHVSRQVLEOH IRUGDPDJHHWF FDXVHGEWKH XVHRI SDUWVRWKHUWKDQ*HQXLQH)XWDEDSDUWV

Servo mount
(Airplane)

Screw
(Helicopter)

$ERXWWKH6%866%86VVWHP

6%86 Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. This servo is connectable with the both sides of S.BUS and S.BUS2 port.
6%86VHUYR LWFDQEHXVHGLQ6%86DQG6%86SRUW 6%86VHUYR LWFDQnotEHXVHGLQ6%86SRUW

&RQQHFWLRQE6%866%86VVWHP@

S.BUS or S.BUS2
compatible receiver

Ch output/ Battery terminal
S.BUS hub

ID:×××-××××× S.BUS hub

ID :×××-×××××

S.BUS or S.BUS2 output

ID :×××-×××××

:KDWLV6%86″ Different from conventional radio control systems the S.BUS system uses data communication to transmit control signals from a receiver to a servo, gyro, or other S.BUS compatible device. This data includes commands such as “move the channel 3 servo to 15 degrees, move the channel 5 servo to 30 degrees” to multiple devices. The S.BUS devices execute only those commands for their own set channel. For this reason, it can be used by connecting multiple servos to the same signal line.Many S.BUS servos is in the connected state, one servo of them can be set it up. The ID code of each servo is used for it. ID code is indicated on the seal of the case. After carrying in a model, it is convenient, if you use attached ID seal and CH seal when ID cannot be seen.

Battery

Conventional servo

ID:×××-××××× ID :×××-××××× S.BUS2 servo

• Can also be used together with conventional servos. * Items required: S.BUS or S.BUS2 receiver, S.BUS2 servo, S.BUS hub,
  S.BUS channel setting toolS.BUS channel setup compatible transmitter /SBC-1 /CIU-2 /S.BUS channel setup compatible receiver

3URFHGXUHIRUXVHZLWKWKH6%866%86VVWHP@

6HWWKHFKDQQHODWWKH6%86VHUYRV

Set the channel at the S.BUS2 servos by using an S.BUS channel setting tool.

• Refer to the S.BUS channel setting tool instruction manual for the S.BUS servo channel setting method.

&RQQHFWWKHVHUYRVWRDQ6%86RU6%86FRPSDWLEOHUHFHLYHU

Connect the servos from the S.BUS or S.BUS2 port of the S.BUS or S.BUS2 compatible receiver via S.BUS hubs.

&RQQHFWLRQWRFRQYHQWLRQDOUHFHLYHU@

Conventional Receiver

Ch output/ Battery terminal

Conventional Servo
S.BUS2 servo

S.BUS2 servo
Battery

• Operation is the same as that of a conventional servo. >2SHUDWLRQEFRQYHQWLRQDOUDGLRFRQWURO@
  An S.BUS2 servo connected to a conventional receiver operates as a conventional servo. The channel becomes the receiver connection point.
  *The contents set by programmable function are effective.

FUTABA CORPORATIONPhone: +81 475 32 6982, Facsimile: +81 475 32 6983 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan ©FUTABA CORPORATION 2013, 2 (2)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>