LASFIT H10 LED Fog Light Bulbs User Manual

LASFIT H10 LED Fog Light Bulbs

PRODUCT MANUAL

Email: service@lasfit.com
Call: 909-758-7900 Mon. – Fri. 9:00 am-5:30 pm (PST) Location: 2235 E 4th St Ste F Ontario, CA 91764 United States

FOREWORD

Package Contents

Bulb2
User Manual!

Customer sevice
Email: service@lasfit.com Call: 909-758-7900
Office Hours: Monday~Friday 9:00 am~5:30 pm (PST)
Location: 2235 E 4th St Ste F Ontario, CA 91764 United States

Installation video
Before installing, you can watch a video to make your installation easier

INSTALLATION STEPS

Hll/H8/H9/Hl6, 9006/HB4, 9005/HB3, Hl0/9145/9140/9055, 5202/2504, Hl3/9008, 9012, 880.

1. Disconnect the power plug.

2. Remove the original bulb.

3. Align the tabs with the notches opening-1.

4. Align the tabs with the notches opening-2.

5. .Turn on to secure the LED bulb.

6. Rotate to keep chip vertical.

7. Put the dust cover back.

H4/HB2/9003, H7, Hl, H3

1. .Remove the dust cover and the Halogen bulb.

2. luster the retainer holder into the assembly slot, match the tabs with slot, and lock the retainer holder with the buckle.

3. lnsert the lamps into the retainer holder with correct position;
   Note : H4 rotate clockwise until the LED chips face 3-9 o’clock.

4. .Rotate the base of the lamps clockwise until it is in the correct position.

5. connecting the plug.

9004/HBl, 9007/HBS Installation steps

1. .Remove the dust cover and halogen bulb, and remove the lock ring of the halogen bulb.

2. Take out the white collar from our LED kit by rooting it.

3. inset the plastic lucking ring (black) into the LED kit from front, then put our white collar bon the led kit.

4. .inset the lamps into the retainer holder with correct position.
   Note: Line up the tiny tab of LED lamps with the slot of retainer holder.

5. .Hold the base of the LED lamps, rotate clockwise until the LED chips face 3-9 O’ clock.
   ( if your highbie and lowbie are reverse, then rotate clockwise by 180′).

6. lf your OEM hood is too long to hold the LED bulb, please modify the hood like in the picture 6.

DECODER AND NOTIFICATION

Decoder and Notification
Some vehicles may meet Compatibility problems, such as flicker, error code and radio interference, thus a decoder could be needed. You can contact us through our service email with your vehicle make/model/year.

Installation steps of the decoder:

 Troubleshooting

FAQ

1. The model of lamps I purchased is different from my OEM halogen lamps. Can I get an exchange for the correct model?
   A: The main reasons:

2. Amazon Confirmed Fit system is not 100% accurate.

3. Your headlight assembly is not an OEM part.
   Please double check the model of your OEM halogen bulb. And contact our Customer Service.

4. The size of the lamps is not correct, they’re either too long or too wide, and LED lamps can’t be installed into the headlight assembly. How can I get proper size lamps for my car?
   A: Some LED lamps are not in a 1:1 ratio with the OEM halogen bulbs.
   The large base is for better heat dissipation and prolonging the life of the lamps. If the lamps are not suitable for installation, please contact the Customer Service.

5. Do you meet the five phenomenon’s below?

6. Errors on instrument panel;

7. The Lamp keeps flashing;

8. Can’t switch between high and low beams;

9. High and low beam reversed;

10. The Lamp does not turn on or off.
    A: The above phenomenon’s are decoding problems, which are mainly caused by the automotive computer failing to detect the correct signal. You can contact Customer Service to obtain the decoder and solve the decoding problem.
    (decoder installation drawing or video)

11. How to adjust the lamps to 3-9 o’clock? I’ve read all the instructions, but still can’t find the method.
    A: We recommend keeping the LED chips facing the 3 o’clock and 9 o’clock positions to ensure the best beam pattern and visual effect. However, it is impossible to adjust to this position for some vehicles. There is no need to worry about the position of the LED chips as long as the beam pattern is acceptable .

12. Why my daytime running lights/DRL are not working or flickering?
    A: Sometimes, if your 900S bulbs and daytime running lights use the same bulbs, the daytime running lights may not working or flickering because of low voltage, the only solution is disabling the DRLs’ function on the setting, please reconsider before placing an order.

13. False Compatibility, this LED Bulb doesn’t fit my vehicle?

14. Open the shopping link of the product, enter your model in the fitment at the top, and it will prompt whether it is suitable.

15. Contact us directly by email.

PRODUCT SPECIFICATION

PRODUCT SPECIFICATION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>