NEXO P15 Source Loudspeaker User Manual

NEXO P15 Source Loudspeaker User Manual

WARNINGS

PRECAUTIONS

Do not open the speaker, do not try to disassemble it neither to modify it in any way. The system doesn’t include any userrepairable part.
If the system seems to be malfunctioning or damaged, stop using it at once and have it repaired by a NEXO qualified technician.
Do not expose the system directly to the sun or to the rain, do not immerse it into fluids, do not place objects filled with liquid on the system. If a liquid gets into the system, please have it inspected by a NEXO qualified technician.
The connection should be performed by qualified technician, by ensuring that power is off.
Operating temperature with temperate climate: 0°C to +40°C (+32°F to +104); -20°C à +60°C (-4°F to +140°F) for storage

SAFETY INFORMATIONS

Read this manual before using the speaker.
Keep this manual available for further reference.
Observe all warnings and cautions.
Please check the NEXO Web site nexo-sa.com to get the most up-to-date version of this manual.
Ensure you are aware of the safety rules applying to rigging, stacking or installing on tripod or speaker stand. Failure to observe these rules may expose persons to potential wounds or even death.
Only use the system with accessories specified by NEXO.
Please always consult a NEXO-accredited technician if the installation needs architectural works and observe following precautions:

Mounting Precautions:

• Please select screws and mounting location supporting 4 times the system weight.
• Do not expose the system to excessive dust, vibrations, to extreme cold or hot temperatures, to reduce the risk of damaging components.
• Do not place the system in an unstable position: it could fall accidentally.
• If the system is used on a tripod, please ensure the tripod’s specifications are adapted and that its height does not exceed 1.40m/55”. Do not move the tripod with the system in position.

Connection and Powering Precautions:

• Unplug connected cables before moving the system.
• Power off the system before connecting the system.
• When switching on the installation, the amplifier must be powered last; when switching the installation off, shut off the amplifier first.
• If you work by cold temperatures, progressively raise the level to nominal value during the first minutes of use, to allow the system components to stabilize.

Please check regularly the system condition.

HIGH SOUND PRESSURE LEVELS

Exposure to very high sound pressure levels may cause permanent hearing losses. Degrees of hearing losses may be different from one person to another, but almost everybody will be affected if exposed to high sound pressure levels during a long period of time. The OSHA (Occupational Safety and Health Administration) American Agency specified the following maximal exposures:

WASTE OF ELECTRIC OR ELECTRONIC EQUIPMENT

This symbol on the product or its packaging indicates that this product must not be treated as household waste.
Instead, it is your responsibility to hand it over to a designated collection point for the recycling of waste electrical and electronic equipment. By ensuring your waste equipment is recycled, you will help prevent potential negative consequences for the environment and human health, which could appear if this product was not recycled. Recycling helps spare natural resources. For more information about the recycling of this product, please contact your local city office, your household waste disposal service or your reseller

EQUIPMENT

3 locations for rigging accessories, one at the back and one per side.

WARNING: The depth of the M10 thread is 22mm (0.84 inch). On both sides, you’ll find a print for speaker stand.

3 locations for connecting, one at the back and one per side.

Pole stand assembly with pole stand or speaker stand

Fix the pole stand on the connector plate (M20) of the Sub.
Mount P15 on the pole stand/speaker stand (diameter of 35mm),

IMPORTANT

Speaker stand must be rated for P15 weight.
Speaker stand must always be installed on a horizontal surface.
Stand height and footprint must be defined to prevent assembly from collapsing.
Ensure that audience is not allowed within a safety area which radius is equal or higher than assembly height.
Test steadiness of the assembly by pushing in all directions.

DESCRIPTION

The P15 is a compact full-range coaxial speaker

Versions

• P15: for Touring Application; black, white
• P15-TIS: for Touring Application, with Grille Installation; black, white

P15 HF Dispersion:

• 60° – 60° with standard horn
• 90° – 40° with PNU-P15FLG9040
• PS with PNU-P15FLGPS (Asymmetrical Dispersion)

P15 can be used alone or with L18 subwoofer

The speaker is equipped with four Speakon NL4 connectors with parallel-wired pins, one on each side and two at the back.
On the back a switch allows to choose between ACTIVE MODE/PASSIVE MODE.

• PASSIVE MODE: 2+/2-. The 1+/1- pins are used by the sub.
• ACTIVE MODE: LF (1+/1-) – HF (2+/2-)

Amplification

• The P15 speakers must be used with a NEXO processor to handle EQ, phase alignment, crossover and excursion/thermal protection for the system loudspeaker. There are two NEXO processor series supporting the P15 speakers: NXAMP (4 channels) amplified processors and DTD processors (stereo + sub). DTD processors ensure optimal performances when used with DTDAMP power amplifiers.
• The following table shows the number of P15 speakers and L18 subwoofers usable with each solution

PRESET

Please consult nexo-sa.com for NEXO TD Controllers firmware information.

For the P15, the following setups are available:

MAIN is the recommended setup for most FOH application, similar to previous firmware setup.

MONITOR is recommended for monitor applications. Warning: this setup is a low latency setup and therefore its phase is not compatible with other NEXO cabinets, including subs.

Passive Mode

• P15 MON PA 6060, with high-pass at 57 or 85 Hz.
• P15 MON PA 9040, with high-pass at 57 or 85 Hz.
• P15 MON PA PSguide, with high-pass at 57 or 85 Hz
• P15 MAIN PA 6060, with high-pass at 57, 85 or 120 Hz.
• P15 MAIN PA 9040, with high-pass at 57, 85 or 120 Hz.
• P15 MAIN PA PSguide, with high-pass at 57, 85 or 120 Hz

Active Mode

WARNING: Do not mix directivity and/or modes

P15 MON HF 6060 with P15 MON LF 6060 =====> OK
P15 MAIN HF 6060 with P15 MON LF 6060 =====> NOT OK
P15 MON HF 9040 with P15 MON LF 6060 =====> NOT OK

• P15 MON HF 6060, 1.2 kHz – 20 kHz.
• P15 MON HF 9040, 1.2 kHz – 20 kHz.
• P15 MON HF PSguide, 1.2 kHz – 20 kHz.
• P15 MON LF, with high pass at 57 or 85 Hz.
• P15 MAIN HF 6060, 1.2 kHz – 20 kHz.
• P15 MAIN HF 9040, 1.2 kHz – 20 kHz.
• P15 MAIN HF PSguide, 1.2 kHz – 20 kHz.
• P15 MAIN LF, with high pass at 57, 85 or 120 Hz.

**Front of house and stage monitor applications

**

Stage monitor applications with Subs (OMNI or CARDIO modes)

**Front of house applications with Subs (OMNI or CARDIO modes)

**

HF DIRECTIVITY

The P15 speaker can be used in horizontal or vertical position.

The standard horn is a 60° – 60° HF dispersion. It’s easy to change the HF dispersion by adding a specific flange. Different mounting possibilities and flange rotation allow to deal with every request.

P15 Unlock the 2 quarter-turn screws, Remove the grille.

Remove the 4 HF Cap and store them

Magnets keep the horn in place

Place the flange, if necessary, rotate it

Replacing the grille

When replacing the grille, ensure it is well positioned in the top blade.

CROSSOVER FREQUENCY

• 57 Hz: Full range application.
• 85 Hz: Use as « front fill » on stage, complementing a main system. Use with a NEXO subwoofer, e.g. L18.
• 120 Hz: Long throw application.

ACCESSORIES

WARNINGS

All P15 accessories are specifically rated in agreement with structural computations.
Never use other accessories – including push-pins – when assembling P15 cabinets than the ones provided by NEXO: NEXO will decline responsibility over the entire P15 accessory range if any component is purchased from different supplier.
PROHIBITED: P15 below P15 or P15 below L18 without dedicated accessory

VNU-BUMP (PNT-BUMP)
LiftBar, use with P15, LIFTADAPT, WMADAPT.
Place VNU-BUMP on P15 (only use the provided screws).
Tight properly
Refer to the Product Data Sheet.

VNU-HBRK600 (PNT-HBRK15)
Horizontal Cradle, use with P15, CLADAPT, PLADAPT.
Place HBRK600 on P15, use only fasteners provided.
Tight properly.
Refer to the Product Data Sheet.

VNU-PLADAPT (PNT-PLADAPT)
Pole adapter, use with P15, HBRK600, VBRK15.
Place VNU-PLADAPT, use only fasteners provided.
Tight properly.
Refer to the Product Data Sheet.

PNU-VBRK15 (PNT-VBRK15)
Vertical Cradle, use with CLADAPT, PLADAPT.
Place VBRK15 on P15, use only fasteners provided.
Tight properly.
Refer to the Product Data Sheet.

VNT-LIFTADAPT (PNT-WMADAPT)
Adapter, use with Truss Clamp, VNU-BUMP.
Refer to the Product Data Sheet.

VNI-WMADAPT (PNT-WMADAPT)
Adapter, use with VNU-BUMP, VNI-WM380.
Refer to the Product Data Sheet.

PNI-P15TOL18
PNI-P15TOL2L18
P15 Under 1xL18
P15 Under 2xL18 (Omni or Cardio)
Se référer à la fiche accessoire

VNI-CLADAPT (PNI-CLADAPT)
Ceiling adapter, use with VNU-HBRK600, PNU-VBRK15.
Screw CLADAPT to the ceiling (fasteners not provided).
Place the assembly on CLADAPT, use the 2 guides. Tight with the fasteners provided with CLADAPT.
Refer to the Product Data Sheet

VNI-WM380 (PNI-WM380)
Wallmount for P15, use with WMADAPT.
Mount the wall plate. Place the arm in the wall plate.
Lock with the provided screw.
Refer to the Product Data Sheet.

PNU-P15FLGPS (PNT-P15FLGPS)
HF Dispersion Horn ‘PS’
Remove the grille, remove the flange to place the PNU-P15FLGPS.
If it necessary, rotate it. Magnets keep the horn in place.
Refer to the Product Data Sheet.

PNU-P15FLG9040 (PNT-P15FLG9040)
HF Dispersion Horn 90° – 40°
Remove the grille, remove the flange to place the PNU-P15FLG9040.
If it necessary, rotate it. Magnets keep the horn in place.
Refer to the Product Data Sheet.

PNT-2CASE15: FLIGHT CASE FOR 2X P15
PNT-ACC15: FLIGHT CASE FOR P15 ACCESSORIES
PNT-COV15: COVER FOR P15

ARRAY EQ

**The ArrayEQ allows to adjust the system frequency response in its lower range (see curves below, with different ArrayEq values):

**

MAINTENANCE

Driver access

P15 Unlock the 2 quarter-turn screws, Remove the grille.
(P15- TIS See above)

Remove the stickers.

Remove the horn.

Remove 8 screws.
Tightening torque: 3.5 Nm (Thread Locker: Loctite 242)

Remove the 2 screws.
Tightening torque: 2.5 Nm (Thread Locker: Loctite 222)

To access to the HF diaphragm, remove 4 screws.
Tightening torque: 2 Nm

Spare parts

NOTE:
Speakers and Grills can be sent back to NEXO for recycling

TECHNICAL SPECIFICATIONS

P15 WITH NEXO ELECTRONICS

Dispersion 50° to 90°x40°
Crossover Frequency| 57Hz – 85 Hz – 120 Hz
Nominal Impedance| Active mode (8Ω LF, 8Ω HF) – Passive mode: 8Ω

SPECIFICATIONS

P15-TIS: Black or white acoustic fabric fitted front Magnelis® steel grille

Fittings

| Handle on both sides

Threated inserts on the back and on both sides for connection of mounting accessories

Stand fitting on both sides (35mm / 1”3/8)

Connector| 4x NL4, 4 poles connectors; 2 at the back and 1 on each side
Weight| 23 kg / 51 lb
Dimensions|

Tel: +33 3 44 99 00 70
Fax: +33 3 44 99 00 30
E-mail: info@nexo.fr

References

• NEXO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>