Pro sKit MT-7076 LCD Network Cable Tester and Probe Kit User Manual

June 16, 2024
Pro sKit

Pro sKit MT-7076 LCD Network Cable Tester and Probe Kit

Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit-
product

Specifications

  • Model: MT-7076
  • Edition: 1st Edition, 2023
  • Measurement Range: 2.5m – 200m
  • Network Cable Compatibility: CAT.5E and CAT.6

Overview
Thank you for purchasing the Pro’sKit MT-7076 LCD Network Cable Tester & Probe Kit. Please read the instructions carefully and pay attention to the following matters before using this instrument. Please keep it properly for future reference.

Caution
Do not connect with DC voltage over 60V or any AC voltage live circuit equipment as it may result in damage.

Diagram

Transmitter socket and keys

  • Flash/PoE/Length connector: For Cable Length/PoE test and Port Flash testing
  • RJ45 (SCAN): For Network Cable Tracing
  • RJ11 connector: For Telephone Cable Tracing
  • QC/CONT connector: For Cable map testing and RJ45 plug crimping testing
  • Long press this key to power on or power off
  • Enter: Press this key for a test choose or setting
  • Left: Press this key to move arrow cursor up or left on LCD to choose function
  • Right: Press this key to move arrow cursor down or right on LCD to choose function
  • ESC: Press this key to return to previous menu
  • Type-C: Charging jack

Receiver socket and keys

  • Sensitivity: Tun on/off. Adjust the receiving signal sensitivity
  • Signal strength indicator: Low, Middle, High
  • SCAN Key: Switch over the receiving signal mode
  • NCV Key: Non-contact test on or off
  • Lamp Key: The flashlight is the key
  • Type-C: Charging jack
  • RJ45 CONT: For Cable map testing

Operation
Press the power key to turn on the device. Use the left or right keys to choose a function. Press the enter key to test. Press the ESC key to return.

Setting

  • CONT: Used to detect the network jumper connection situation and fault judgement. Test results such as open, short, crossing, etc.
  • Length: Used to detect the length of the network cable. Measuring range is 2.5-200 meters. Applicable to CAT.5E and CAT.6 network cable.
  • SCAN: Used to find the target network cable. The transmitter and receiver should be used together. The transmitter transmits the audio signal, and the receiver receives the signal.
  • PoE: For PoE switch supply line, voltage, PoE standard (IEEE 802.3.af/at) or non-standard PoE testing.
  • Flash: Used to find the corresponding interface on the other end of the target network cable on the switch. Transmit the signal to flash the switch interface light and test the performance of the switch: 10M/100M/1000M; FDX/HDX; Auto-Nego/Non-Auto Nego, etc.
  • QC: Used to detect the network cable plug and network cable crimping is through or fail.

CONT
Insert the pending network cable into the transmitter QC/CONT RJ45 socket in the right and the other end into the receiver socket. Select the CONT menu and press Enter to test with test results shown below: UTP STP Short disconnection crossover If the display cable open indicates that the network jumper is all open or the other end of the network cable is not inserted in the test receiver, or the test interface is wrong.

Measure Cable Length
Cable length measurement range: 2.5m – 200m. Applicable to CAT.5(CAT5e) and CAT.6 network cable. Insert the pending network cable into the transmitter Flash/PoE/Length RJ45 socket at the head of the transmitter. Do not plug in any socket at the other end. Select the Length menu and press Enter, and access the menu below. Select the network cable type CAT 5 or CAT 6 in the Type menu.

FAQ

  • Q: What is the measurement range for cable length?
    A: The measurement range for cable length is 2.5m – 200m.

  • Q: Which network cable types are compatible with this tester?
    A: This tester is compatible with CAT.5E and CAT.6 network cables.

  • Q: How do I detect the network jumper connection situation and fault judgement?
    A: Insert the pending network cable into the transmitter QC/CONT RJ45 socket and the other end into the receiver socket. Select the CONT menu and press Enter to test.

  • Q: How do I measure the length of a network cable?
    A: Insert the pending network cable into the transmitter Flash/PoE/Length RJ45 socket. Do not plug in any socket at the other end. Select the Length menu and press Enter.

MT-7076
LCD Network Cable Tester & Probe Kit

User’s Manual
1st Edition, 2023
©2023Copyright by Prokit’s Industries Co., Ltd.

OVERVIEW

Thank you for purchase Pro’sKit MT-7076 LCD Network Cable Tester & Probe Kit. Please read the instructions carefully and pay attention to the following matters before using this instrument, please keep it properly for future reference.
MT-7076 is a new anti-interference line finding scheme using digital signal receiving and decoding technology, anti-interference degree is higher, more accurate, eliminate false positives. At the same time, it has the functions of analog line finding, anti-interference line finding, network cable connection testing, network cable length testing, PoE testing, Port Flash & Switch details testing, network cable plug connectors test, etc. LCD display screen. Users can select display language in Chinese or English.

Caution

  • This device is powered by a lithium polymer battery. With the TYPE-C charging interface, please use the USB charger to charge the product. Please remove the charger after full charge. Do not charge for a long time, so as not to cause product damage or fire or other accidents. This product is not equipped with a charger.
  • If you do not use the product for a long time, please charge the product once every 3 months, To keep the battery active and avoid battery damage.
  • This product is strictly prohibited to access the live lines above voltage DC 60V or any AC voltage.
  • Please do not perform related operations on the communication line during thunderstorms to prevent lightning strikes and personal safety.
  • Do not place this product in dusty, wet and temperatures above 40℃.
  • Please do not disassemble the device. Repair and maintenance should be done by a professional staff.

Diagram

Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit-
\(1\) Transmitter socket and keys

  1. Flash/PoE/Length connector: For Cable Length/PoE test and Port Flash testing
  2. RJ45( SCAN): For Network Cable Tracing.
  3. RJ11 connector: For Telephone Cable Tracing.
  4. QC/CONT connector: For Cable map testing and RJ45 plug crimping testing.
  5. “  ”: Long press this key to power on or power off.
  6. “Enter” : Press this key for a test choose or setting.
  7. “Left” : Press this key to move arrow cursor up or left on LCD to choose function.
  8. “Right”: Press this key to move arrow cursor down or right on LCD to choose function.
  9. “ESC” key: Press this key to return to previous menu.
  10. Type-C: Charging jack.

Receiver socket and keys

  1. Sensitivity: Tun on/off: Adjust the receiving signal sensitivity.
  2. Signal strength indicator:
    • Low: The signal is weak;
    • Middle: The signal is middle;
    • High: The signal is high.
  3. SCAN Key: Switch over the receiving signal mode.
  4. NCV Key: Non-contact test on or off.
  5. Lamp   Key: The flashlight is the key.
  6. Type-C: Charging jack.
  7. RJ45 CONT: For Cable map testing

Operation

Do not connect with DC voltage over 60V or any AC voltage live circuit equipment or it will result damage.

Press “ ”key to power on, as show blow. Press “Left ” or“ Right ”key to choose function. Press “Enter” key to test. Press “ESC” key to return. Pro-sKit-
MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(3\)

  • CONT : It is used to detect the network jumper connection situation and fault judgement; Test results such as open, short, crossing, etc.
  • Length : It is used to detect the length of the network cable; the measuring range is 2.5-200 meters. Applicable to CAT.5E and CAT. 6 network cable.
  • SCAN : It is used to find the target network cable; the transmitter and receiver should be used together. The transmitter transmits the audio signal, and the receiver receives the signal.
  • PoE : For PoE switch supply line, voltage, PoE standard (IEEE 802.3.af/at) or non-standard PoE testing.
  • Flash : It is used to find the corresponding interface on the other end of the target network cable on the switch, transmit the signal to flash the switch interface light, and test the performance of the switch: 10M/100M /1000M; FDX/HDX; Auto-Nego/Non-Auto Nego, etc.
  • QC : It is used to detect the network cable plug and network cable crimping is “through” or “fail”.

CONT

  • Insert the pending network cable into the transmitter (QC/CONT) RJ45 socket in the right and the other end into the receiver socket.
  • Select the “CONT” menu and press “Enter” to test with test results shown below: Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(4\)
  • If the display “cable open ” indicates that the network jumper is all open or the other end of the network cable is not inserted in the test receiver, or the test interface is wrong.

Measure Cable Length
Cable length measurement range:2.5m~200m; Applicable to CAT.5(CAT5e) and CAT. 6 network cable.

  • Insert the pending network cable into the transmitter “Flash/PoE /Length” RJ45 socket at the head of the transmitter. Do not plug in any socket at the other end.
  • Select the “Length” menu and press “Enter”, and access the menu below, Select the network cable type CAT 5 or CAT 6 in the Type menu. Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(6\)
  • Units of length can select “Meter” “Yard” “Foot” under the Units menu.
  • Select the “Start Test” menu and press “Enter” to test with test results shown below: Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(7\)
  • Because each pair of wire has different twisted density, it is normal to measure the numbers slightly different, which can be measured many times to get the same measurement value.
  • From the image, it means there exists problem at 12.1m. To make sure it is short or broke there, you can test it continuity to know details. Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(8\)

NOTE : Kind reminds when measuring cable length.

  1. Only one end of the network cable is inserted into the transmitter test interface, and no network interface should be inserted at the other end of the network cable.
  2. The range must be 2.5m—200m, otherwise , it would be display the incorrect numbers or display as shown above (right).

SCAN (Cables tracking)
Do not connect with DC voltage over 60V or any AC voltage live circuit equipment or it will result damage. The cables tracking function has two modes: digital mode and Analog mode, The receiver and transmitter signals must be consistent to receive the signal.

  • Connect one end of the target cable to the (SCAN) RJ45 socket at the head of the transmitter. Telephone cable can be connected to the RJ11 socket in the right of the transmitter.
  • Select the “SCAN” menu and press “Enter” to transmit and show below:Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(9\)
  • The receiver knob rotates clockwise with a “beep”. You can rotate clockwise to the maximum position with higher reception sensitivity.
  • The receiver startup defaults in the digital signal receiver mode. You can press the “SCAN” key to switch to the receive signal mode. Analog signal reception mode, the SCAN indicator light flashes. Digital mode, the SCAN indicator is long and bright.
  • While the probe is close to the network cable to be measured, the speaker emits a clear “beep-beep ” sound, and the network cable contacted by the receiver probe is the target network cable to find.
  • When tracking a cable in the working network, due to the network switch, there may be audio signals adjacent to the target cable, each cable can be removed to find the target cable or try to rotate the receiver sensitivity knob counterclockwise to reduce the reception sensitivity to find the target cable.

PoE Testing

  • Insert the network cable into the transmitter RJ45 socket (Flash/PoE/Length) at the head of the transmitter and the other end of the cable to the PoE switch.
  • Select the “PoE” menu and press “Enter” to test.
  • The display shows the test results: if the tested PoE switch is a standard PoE switch, display the PoE power supply mode, standard type, PoE voltage, voltage positive and negative electrode, etc. As shown in the figure below: Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(10\)
  • The figure shows that the power supply line supplies power to 12 36 line, span mode is “End span”; standard type is IEEE 802.3at; voltage is 53.6V; polarity “-” means that the left two lines are negative voltage poles; if display “+” means that the left two lines are voltage “+” pole.
  • If the tested device is non-standard PoE device, display as blow: Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(11\)
  • The figure shows that the power supply line is 8 pins. Non-standard PoE equipment. Voltage is 53.6V; Voltage polarity is not displayed when 8 pins power supply.
  • The test result can usually be displayed within a few seconds. If the test result is not displayed when the test time is more than 30 seconds, the tested device may not be a PoE switch, or the test interface may be wrong.

Port Flash & Switch Details Testing
This function transmits the pulsing signal through the transmitter to flashing the LED indicator of the network switch, then can locate the interface of the network cable on the switch. At the same time, the network switch working performance can be tested.

Do not connect with DC voltage over 60V or any AC voltage live circuit equipment or it will result damage.

  • Insert the network cable into the transmitter RJ45 socket (Flash/PoE/Length) at the head of the transmitter and the other end of the cable to the network switch.
  • Select the “Flash” menu and press “Enter” to start testing.
  • The 2 indicators on the RJ45 jack port will be lit and flash. Then observe the ports on switch, if there is a port whose flash frequency is 3 secs, and slower than all the other ports, it tells you the port is target one you’re looking for.
  • Also, the device can tell you the connected switch’s information, such as its speed (10M/100M/1000M), transmitting modes (FDX: full duplex/ HDX: half duplex) Protocol (Auto- Nego / Non-Auto-Nego). See the graph for ref. as below.Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(12\)

If “Time out” is displayed, the reasons may be: 1. Network cable insertion error and test interface; 2. Network cable is not connected to the switch; 3. Network cable fault. 4. Switch, router fault or incompatibility with the instrument. 5. This instrument fails.

QC (RJ45 Connectors Testing)
QC: It is used to test whether the cable core is connected to the copper sheet of the RJ45 connector when you crimp a plug or not sure a plug is good.

  • Insert the network cable (RJ45 plug) into the transmitter’s RJ45 (QC/CONT) socket.
  • Select the “QC” menu and press “Enter” to start testing.
  • The test result showing “√” indicates that the cable is normal. If “×” appears, the line is failed. As shown in the figure below: Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(13\)

Setting
This function can set the language (Chinese / English), backlight time, automatic shutdown time, contrast, etc.

  • Select the “Setting” menu and press “Enter” to start setting. Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(14\)
  • Backlight setting: Press the “Enter” key to set.
  • Adjust the backlight time among 15S, 30S, 60S, on and off. Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(15\)
  • Auto-off time setting: Press the “Enter” key to set.
  • Adjust the Auto-off time among 15mins, 30mins, 1hour, off.
  • Contrast setting:
  • Select the “Contrast” to setting. And press “Right” or “Left” key to adjust the contrast to suit yourself. Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit- \(16\)
  • Version information : Press the “Enter” key to set.
  • To check version information of software and hardware. as above.

Non-contact Voltage Detection (NCV)
This function is used to determine whether the wire or equipment has an AC voltage, the detection range AC70-1000V (50 / 60Hz).

  • Tun on the receiver and press “NCV” key, The indicator light on.
  • Put the receiver probe close to the target body, if the AC voltage is detected, the speaker emits an alarm sound of different frequency, the speaker rapid sound indicates a high voltage or fire line, the slow sound may be low voltage or zero line.

Note

  • This function is for reference, the voltage may remain even there is no detection showed up. There are many possible factors might block the detection.
  • There are external sources (like flashlight and motor) may trigger non-contact voltage detection.

Flashlight
Tun on the receiver and press “Lamp” key, the indicator and the front LED auxiliary lighting LED is turned on for lighting with insufficient light. Press the key again to tun off.

Charge the Product

The transmitter and receiver of this product are both built-in 3.7V 1400mAh lithium battery, TYPE-C charging interface, which can use the mobile phone or other USB charger to charge this product, but this product is not equipped with the charger.

  • When the battery symbol of the transmitter display screen flashes, the receiver power indicator light flashes, indicating that the battery voltage is insufficient, please charge in time to avoid affecting the work.
  • Please pull out the charger in time. Do not charge for a long time to avoid damage to the instrument.
    If this product is not used for a long time, please charge once every 3 months, so that the lithium battery remains active, to avoid damage to the lithium battery.

Accessories

Parts QTY Parts QTY
Transmitter 1pc RJ45/RJ11/Alligator clips Cable 1set
Receiver 1 pc User Manual 1 pc
Type-C Cable 1 pc Storage bag 1 pc
Earphone 1 pc

Specification

MT-7076 Transmitter Specifications

Display| LCD 53x29mm(128×64 Dots)
Language| Chinese/English
Connectors| RJ45x3; RJ11x1
**** Cable Map| Cable Type:CAT.5; CAT.5e; CAT.6; CAT.7
Display: R&M; 1-8/G
Max range: 300m


**** Transmission

| Singal:Analog mode/Digital mode
Max. Signal Voltage: 5.0V±1.0Vp-p
Frequency:455kHz
Cable Type:CAT5/ CAT5e/CAT6 STP/UTP ; Telephone cable
Scan range:1km(Analog mode) / 600m(Digital mode)
Cable Length| 2.5~200m CAT.5(CAT5e)/CAT.6
Measurement|

  • accuracy:≤20m,±1.6m;20m~100m, ±2.4m;
  • 100m~200m, ±3.2m

---|---
Unit: m/yd/ft
Port Flash| Frequency: 1time/3sec;
Link test:10M/100M/1000M; FDX/HDX; Auto-Nego/Non-Auto Nego.
**** PoE Testing| Type: IEEE802.3af/at; Non-Standard
Midspan / Endspan /8 pins;
Voltage values
QC Testing| Connector RJ45 8pin; ≥10cm
Back Light| 15sec/30 sec /60 sec /on/off
Auto OFF| 15min/30min/60min/off
Battery| 3.7V 1400mAh Li-ion
Dimension| 125x70x32 mm
MT-7076 Receiver Specifications
Receiver signal| Analog mode/ Digital mode
Vocality| Doble Vocality
Sensitivity| knob-operated control
Flashlight| 1 LED
NCV| AC 70V-1000V 50/60Hz
Low Battery| Power light flashing
Earphone jack| Φ3.2mm
Battery| 3.7V 1400mAh Li-ion
---|---
Dimension| 198x50x28 mm

MAINTENANCE & TROUBLESHOOTING

Warning

  • Do not try to open the product shell without authorization.

Disconnect all external connection lines before opening.

Caution

To avoid damaging the case, do not use solvents or abrasive cleansers. Clean the case with a soft cloth dampened with water or a mild soap solution.

Troubleshooting

Possible Problems Troubleshooting
Line order fault displayed incorrect 1. Adjust the two ends of the network

jumper, and then test again.
2. Test the socket insertion error, please insert the correct test socket.
3. Instrument failure, send to the dealer for repair.
The receiver could not detect the signal from the audio transmitter| 1. The receiver is not consistent with the transmitter signal mode. Refer to the SCAN operating instructions.
2. Test the socket insertion error, please insert the SCAN or RJ 11 socket.
3. The receiver sensitivity is too low: rotate the sensitivity adjustment knob clockwise to maximum detection.
| 4. The emitter signal conflicts with the switch signal. You can switch to anti- interference mode. And you can also use the crocodile clip line to connect the test network line of 2 retest
---|---
5. Instrument failure, send to the dealer for repair.
Other abnormal functions| 1. Test the socket insertion error, please insert the correct test socket.
Instrument failure, send to the dealer for repair.

Pro-sKit-MT-7076-LCD-Network-Cable-Tester-and-Probe-Kit-
\(17\) PROKIT’S INDUSTRIES CO., LTD

http://www.prokits.com.tw
E-mail : pk@mail.prokits.com.tw

©2023 Copyright by Prokit’s Industries Co., LTD. All rights reserved 2023001(A)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals