SPORTS ATTACK 2883 Volleyball Pitching Machine Instruction Manual

SPORTS ATTACK 2883 Volleyball Pitching Machine Instruction Manual

INTRODUCTION

Thank you for purchasing this Sports Attack LLC. equipment
Proper assembly, careful operation and consistent maintenance of this equipment will ensure that it gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly set up the Skill Attack, as well as to use, care for and maintain the Skill Attack in a manner which will ensure its optimum performance.

RECEIVING THE PRODUCT

Please check the contents of your boxes to ensure you have received all parts for the machine. If anything is missing or damaged, call Sports Attack Customer Service, 800-717-4251. If the product or package has been damaged in shipping, note on
shipping tag, save all evidence of damage along with related documents and contact the shipper immediately.

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

Use a 115 volt single phase 3-wire (2 wire with ground) grounded power source.
Up to 200 ft. from power source, use a minimum #14/3 grounded 3-wire 15 amp minimum rating extension cord.
Over 200 ft. from power source, consult a licensed electrician for required power cord size.

OPERATING SAFETY

CAUTION: Carefully check Skill Attack for completeness and condition before connecting to electrical power:

1. Never reach hands into throwing wheel
2. Always use the Skill Attack with throwing wheel guards in
3. Use the Skill Attack only under adult
4. Use the Skill Attack only for its intended
5. Do not operate the Skill Attack with a damaged cord or plug if the machine malfunctions or has been
6. Check machine before turning “ON” to make sure there are no foreign object in feed
7. If ball becomes lodged and stops motor, immediately turn the Skill Attack “OFF” before
8. To dislodge ball from throwing wheel, unplug machine and push ball through Do not reach hand into feed chute with the machine running.
9. Only one person at a time should operate the Skill
10. Do not allow anyone to walk directly in front of the Keep face and hands away from ball exit.
11. A ball should always be test thrown from the Skill Attack before beginning any Throw several balls to verify end location.
12. Keep hands, hair and loose clothing away from moving
13. Do not use near water or use damp or wet

ASSEMBLY INSTRUCTIONS

Tools required: Wrench for casters (provided. See Figure 2).

STEP ONE

Lay out all parts and check them against parts list. Call customer service immediately if any parts are missing. Please have applicable part numbers as shown on parts list (See page 10).

STEP TWO

Screw on casters to the end of legs. Tighten with the wrench provided (See Figure 2).

STEP THREE

Insert the three legs into tripod sockets, make sure snap button is in place.

STEP FOUR

Remove the carriage bolt and knob from throwing head (See figure 1).

STEP FIVE

Attach throwing head into the tripod assembly.

STEP SIX

Attach the carriage bolt and knob. Make sure its tight.
Assembly is now complete and your Skill Attack Volleyball Machine is ready for use.
See instructions in the manual and on the decals on the machine for operating procedures and options.

SKILL ATTACK OPERATION

The Skill Attack is the perfect individual training machine. No special training other than the complete careful reading of this manual is required to operate.

INCREASE OR DECREASE SPEED

1. Before turning machine “ON,” turn dials located on the throwing head to the “OFF”
2. Turn power switch to “ON.” Turn speed control knobs clockwise to turn the machine “ON” and to increase
3. Turn the speed control knobs counterclockwise to decrease

BALL SPIN, BREAK OR MOVEMENT

1. Floater – Both knobs turned to the same setting, making the wheels spin at the same
2. Top Spin – Upper wheel turning fast, lower wheel turning Variations of the ball spin and break are determined by the wheel speeds.

HORIZONTAL CONTROL                           __

1. Loosen to vary
2. Tighten for

SKILL ATTACK SHUTTING DOWN

TURNING SKILL ATTACK “OFF”

1. Set each speed control dial to “0.”
2. Turn the on/off switch “OFF.”

Unplug Skill Attack from the power source

TRANSPORTING

CARE & CLEANING

LUBRICATION

1. Once per season, or as required.
2. Throwing wheel motors are sealed and require no lubrication.

EXAMINE THE MACHINE

Examine Skill Attack for condition and completeness before every use:

1. Throwing wheels must be tight on the motor
2. Check that the keyway retaining bolts are
3. Wheel guard and ball chute must be securely fastened to the throwing

COMPONENT REPLACEMENT

THROWING WHEEL REPLACEMENT

1. Turn the power switch “OFF” and unplug the power
2. Hold the wheel so that it cannot Turn the retaining screw counterclockwise using a 1/2” open end wrench.

SUGGESTION: If the screw is too tight, give the opposite end of the wrench a series

of light taps with a hammer making sure the wrench remains on the screw.

3. Remove the
4. Work the wheel off of the motor

Reassemble in reverse order.

1. Install wheel to motor
2. Test the wheel by spinning it by hand and making sure that it spins freely without wobble before turning the unit “ON.”
3. Be sure the wheel guard is properly and securely

MOTOR REPLACEMENT

1. Turn the power switch “OFF” and unplug the power
2. Remove the throwing
3. Remove four screws holding controller into main control box. Note the position of the motor wires on the controller, then disconnect the
4. Note the routing of the motor Loosen any wire clamps.
5. Remove bolts holding the motor to the main

Reassemble in reverse order.

COMPONENT REPLACEMENT (cont’d)

CONTROLLER REPLACEMENT

1. Turn the on/off switch “OFF” and unplug the power
2. Remove the four screws holding controller Note the position of the main power and motor wires on the controller, then disconnect the wires.
3. Reassemble in reverse
4. Be sure wires are correctly Motor wire connectors are different sizes. Be sure they are installed on the correct size terminal.
5. When attaching the knobs, turn the speed control shafts fully counter-clockwise, then install the knobs with the pointer to “0.”

SKILL ATTACK™

SKILL ATTACK PARTS LIST

EM

1

| PART NO.

3113-9060-1

| DESCRIPTION

Wrench, Skill

| QTY PER

1

| Service Departmen Ph 800.717.4251

Fx 775.345.2883

---|---|---|---|---
 |  | Caster|  |
2| 3313-4103-1| Locking Caster| 3|
3| 3312-5079-1| Leg, Skill Attack| 3|
4| 3312-5071-1| Undercarriage Tripod| 1|
5| 3323-6048-1| Horizontal Control Knob| 1|
6| 1213-6877-1| Controller Potentiameter Knob| 2|
7| 3362-6148-1| Controller Assembly| 1|
8| 3312-5073-1| Yoke| 1|
9| 3323-6046-1| Elevation Control Knob| 1|
10| 3312-5085-1| Ball Feed Chute| 1|
11| 3343-5080-1| Throwing Wheel| 2|
12| 1332-9836-1| Wheel Motor| 2|

WARRANTY STATEMENT

What is most important to Sports Attack is that your machine meets your expectations of quality and performance. We stand behind the material and workmanship of our machines for five (5) years from the date or original purchase for institutional and residential use and one (1) year for commercial environments, with the following exceptions:

-Throwing Wheels are warranted for two (2) years;

-Electronic Controller is warranted for two (2) years; and,
-Throwing Wheel Motors are warranted for two (2) years.

This warranty excludes any cosmetic issues or normal wear and tear of the unit, and is not in effect if the machine has been misused, misapplied, improperly assembled, or modified without the express written permission of Sports Attack. In addition, this warranty does
not apply to damage in transit, in any accident unrelated to the direct operation of the equipment, or by fire, flood or act of God.
If you encounter any issues during the warranty period, Sports Attack will quickly get your machine back in working order. If the warranty repair involves a replacement part, we will make sure you get both the part and easy instructions for replacement at no cost to you. If a service person is needed, Sports Attack will pay the pre-approved labor charge to get your machine back in working order.
EFFECTIVE IMMEDIATELY: Warranty components such as motors, etc. now require a picture of the component when submitting replacement request.
Please know that any problem can quickly be resolved with a phone call to our experienced, responsive customer service department at 800.717.4251. We are here to answer your questions and to make sure your machine provides you years of service.

RETURNS

Sports Attack manufactures the highest quality sports training equipment in the world. If for any reason you are not satisfied, a machine can be returned within 30 days of receipt for any reason for a full refund less a 15% restocking fee. Cost of shipping the unit back to Sports Attack will also be the responsibility of the purchaser. Please note that the refund amount may be reduced by any non-cosmetic damage to the machine.
If you have any questions or concerns, please give our experienced, responsive customer service department a call at 800.717.4251.

SHIPPING DAMAGE CLAIMS PROCEDURE

NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory.
Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED:

1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt, and that the note of loss or damage is signed by the delivery
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the
3. CONCEALED LOSS OR DAMAGE: If damage is unnoticed until the merchandise is unpacked, notify the transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with This must be done within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.

Sports Attack LLC. cannot assume liability for damage or loss incurred in transit. We will, however, at your request, supply you with the necessary documents to support your claim.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>