SPORTS ATTACK Skill Attack Pitching Machine Instruction Manual

: June 9, 2024
: SPORTS ATTACK

Table of Contents

SPORTS ATTACK Skill Attack Pitching Machine Instruction
WARRANTY STATEMENT
INTRODUCTION
SAFETY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Skill Attack Operation and Shutting Down
CARE & CLEANING
Component Replacement
SKILL ATTACK™
PARTS LIST KEY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SPORTS ATTACK Skill Attack Pitching Machine Instruction

VOLLEYBALL PITCHING MACHINE

SKILL ATTACK™ PITCHING MACHINE PATENTS APPLIED FOR
INSTRUCTION MANUAL
OPERATION · SETUP · USE & CARE · SERVICE
SPORTS ATTACK LLC. | 800.717.4251 | www.sportsattack.com

WARRANTY STATEMENT

What is most important to Sports Attack is that your machine meets your expectations of quality and performance. We stand behind the material and workmanship of our machines for five (5) years from the date or original purchase for institutional and residential use and one (1) year for commercial environments, with the following exceptions:

Throwing Wheels are warranted for two (2) years;
Electronic Controller is warranted for two (2) years; and,
Throwing Wheel Motors are warranted for two (2) years.

This warranty excludes any cosmetic issues or normal wear and tear of the unit, and is not in effect if the machine has been misused, misapplied, improperly assembled, or modified without the express written permission of Sports Attack. In addition, this warranty does not apply to damage in transit, in any accident unrelated to the direct operation of the equipment, or by fire, flood or act of God. If you encounter any issues during the warranty period, Sports Attack will quickly get your machine back in working order. If the warranty repair involves a replacement part, we will make sure you get both the part and easy instructions for replacement at no cost to you. If a service person is needed, Sports Attack will pay the pre-approved labor charge to get your machine back in working order.

EFFECTIVE IMMEDIATELY : Warranty components such as motors, etc. now require a picture of the component when submitting replacement request.
Please know that any problem can quickly be resolved with a phone call to our experienced, responsive customer service department at 800.717.4251. We are here to answer your questions and to make sure your machine provides you years of service.

RETURNS
Sports Attack manufactures the highest quality sports training equipment in the world. If for any reason you are not satisfied, a machine can be returned within 30 days of receipt for any reason for a full refund less a 15% restocking fee. Cost of shipping the unit back to Sports Attack will also be the responsibility of the purchaser. Please note that the refund amount may be reduced by any non-cosmetic damage to the machine.
If you have any questions or concerns, please give our experienced, responsive customer service department a call at 800.717.4251.

SHIPPING DAMAGE CLAIMS PROCEDURE
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory.
Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:

VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt, and that the note of loss or damage is signed by the delivery person.
FILE CLAIM FOR DAMAGE IMMEDIATELY : Regardless of the extent of
the damage.
CONCEALED LOSS OR DAMAGE: If damage is unnoticed until the merchandise is unpacked, notify the transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them. This must be done within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.

Sports Attack LLC. cannot assume liability for damage or loss incurred in transit. We will, however, at your request, supply you with the necessary documents to support your claim.

Warranty/Shipping
To register the Warranty, please go to our website: sportsattack.com/warranty
For repairs and service after the Warranty period, please call:
Sports Attack
Customer Service Dept.
Ph 800.717.4251
Fx 775.345.2883

RETURNS
To return an item, please contact our Customer Service Department at 800.717.4251.
A 15% restocking fee will be charged for any items accepted for return. It is the customer’s responsibility to handle the repacking and shipment (as well as all associated fees) back to Sports Attack.
No returns will be accepted after 30 days of receiving product.

INTRODUCTION

Thank you for purchasing this Sports Attack LLC. equipment.
Proper assembly, careful operation and consistent maintenance of this equipment will ensure that it gives you the very best performance and a long, economical service life. This manual contains the information needed to properly set up the Skill Attack, as well as to use, care for and maintain the Skill Attack in a manner which will ensure its optimum performance.

RECEIVING THE PRODUCT
Please check the contents of your boxes to ensure you have received all parts for the machine. If anything is missing or damaged, call Sports Attack Customer Service, 800-717-4251. If the product or package has been damaged in shipping, note on shipping tag, save all evidence of damage along with related documents and contact the shipper immediately.

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

Use a 115 volt single phase 3-wire (2 wire with ground) grounded power source.
Up to 200 ft. from power source, use a minimum #14/3 grounded 3-wire 15 amp minimum rating extension cord.
Over 200 ft. from power source, consult a licensed electrician for required power cord size.

OPERATING SAFETY
CAUTION: Carefully check Skill Attack for completeness and condition before connecting to electrical power:

Never reach hands into throwing wheel area.
Always use the Skill Attack with throwing wheel guards in place.
Use the Skill Attack only under adult supervision.
Use the Skill Attack only for its intended purpose.
Do not operate the Skill Attack with a damaged cord or plug if the machine malfunctions or has been damaged.
Check machine before turning “ON” to make sure there are no foreign object in feed chute.
If ball becomes lodged and stops motor, immediately turn the Skill Attack “OFF” before dislodging.
To dislodge ball from throwing wheel, unplug machine and push ball through chute. Do not reach hand into feed chute with the machine running.
Only one person at a time should operate the Skill Attack.
Do not allow anyone to walk directly in front of the machine. Keep face and hands away from ball exit.
A ball should always be test thrown from the Skill Attack before beginning any drill. Throw several balls to verify end location.
Keep hands, hair and loose clothing away from moving parts.
Do not use near water or use damp or wet balls.

WARNING PERSONAL INJURY HAZARD

Carefully read all instructions in this manual, and all labels and warnings on the Skill Attack before using this machine. Use machine only under adult supervision. Failure to operate Skill Attack as described in this manual can result in severe personal injury or death.

ELECTRICAL SHOCK HAZARD
Skill Attack volleyball machine must be connected to a properly grounded electrical receptacle.

Do not operate on wet ground.

WARNING PERSONAL INJURY HAZARD
Keep hands away from throwing wheels anytime the machine is connected to a power source.
Carefully check Skill Attack for completeness and condition before connecting it to electrical power.

EQUIPMENT ELECTRICAL DAMAGE
DO NOT plug in or energize this equipment until all Assembly Instructions (see page 5) and Operation Instructions (see page 6) are read and followed.

ASSEMBLY INSTRUCTIONS

Tools required: Wrench for casters (provided. See Figure 2).

STEP ONE
Lay out all parts and check them against parts list. Call customer service immediately if any parts are missing. Please have applicable part numbers as shown on parts list (See page 10).
STEP TWO
Screw on casters to the end of legs. Tighten with the wrench provided (See Figure 2).
STEP THREE
Insert the three legs into tripod sockets and tighten handles as shown in A.
STEP FOUR
Loosen handle E and insert yoke shaft F into tube at G. Then tighten handle E snuggly.
STEP FIVE
Attach throwing head to yoke plate by loosening throwing head thumb screw and fitting base bolt through bottom plate hole in throwing head and secure. Tighten throwing head thumbscrew into base bolt B.
Assembly is now complete and your Skill Attack Volleyball Machine is ready for use.
See instructions in the manual and on the decals on the machine for operating procedures and options.

SPORTS-ATTACK-Skill-Attack-Pitching-Machine-Instruction-
fig-1

To order additional parts, please call:
Sports Attack Customer Service Department
Ph 800.717.4251
Fx 775.345.2883

Skill Attack Operation and Shutting Down

SKILL ATTACK OPERATION
The Skill Attack is the perfect individual training machine. No special training other than the complete careful reading of this manual is required to operate.

INCREASE OR DECREASE SPEED

Before turning machine “ON,” turn dials located on the throwing head to the “OFF” position.
Turn power switch to “ON.” Turn speed control knobs clockwise to turn the machine “ON” and to increase speed.
Turn the speed control knobs counterclockwise to decrease speed.

BALL SPIN, BREAK OR MOVEMENT

Floater – Both knobs turned to the same setting, making the wheels spin at the same RPM.
Top Spin – Upper wheel turning fast, lower wheel turning slowly. Variations of the ball spin and break are determined by the wheel speeds.

HORIZONTAL CONTROL

Loosen to vary direction.
Tighten for repeatability.

SKILL ATTACK SHUTTING DOWN
TURNING SKILL ATTACK “OFF”

Set each speed control dial to “0.”
Turn the on/off switch “OFF.”
Unplug Skill Attack from the power source.

TRANSPORTING

Turn the machine “OFF” and unplug.
Detach throwing head from tripod and carry. See Figure 3.

CARE & CLEANING

LUBRICATION

Once per season, or as required.
Throwing wheel motors are sealed and require no lubrication.

EXAMINE THE MACHINE
Examine Skill Attack for condition and completeness before every use:

Throwing wheels must be tight on the motor shafts.
Check that the keyway retaining bolts are tight.
Wheel guard and ball chute must be securely fastened to the throwing head.

CAUTION PERSONAL INJURY HAZARD
Never attempt to clean the throwing wheels while they are turning. Rags or implements caught in spinning wheels can cause serious injury.
Unplug the machine before cleaning the wheels or performing any service.

CHEMICAL HAZARD
Methyl Ethyl Ketone (M.E.K) Read and follow the directions and safety instructions on the M.E.K container.

FIRE HAZARD
Methyl Ethyl Ketone (M.E.K) M.E.K. is flammable. Do not use M.E.K. around a fire or flame. Do not use M.E.K. near a running generator or other source of ignition.

Component Replacement

THROWING WHEEL REPLACEMENT

Turn the power switch “OFF” and unplug the power cord.
Hold the wheel so that it cannot move. Turn the retaining screw counterclockwise using a 1/8” allen wrench.
SUGGESTION: If the screw is too tight, give the opposite end of the wrench a series of light taps with a hammer making sure the wrench remains on the screw.
Remove the screw.
Work the wheel off of the motor shaft.
Reassemble in reverse order.
- a. Install wheel to motor shaft.
- b. Be sure the spacer is in place.
- c. Tighten the allen head screw.
- d. Test the wheel by spinning it by hand and making sure that it spins freely without wobble before turning the unit “ON.”
- e. Be sure the wheel guard is properly and securely reinstalled.

MOTOR REPLACEMENT

Turn the power switch “OFF” and unplug the power cord.
Remove the throwing wheel.
Remove four screws holding controller into main control box. Note the position of the motor wires on the controller, then disconnect the wires.
Note the routing of the motor wires. Loosen any wire clamps.
Remove bolts holding the motor to the main frame.

Reassemble in reverse order.

CONTROLLER REPLACEMENT

Turn the on/off switch “OFF” and unplug the power cord.
Remove the four screws holding controller faceplate. Note the position of the main power and motor wires on the controller, then disconnect the wires.
Reassemble in reverse order.
- a. Be sure wires are correctly reinstalled. Motor wire connectors are different sizes. Be sure they are installed on the correct size terminal.
- b. When attaching the knobs, turn the speed control shafts fully counter-clockwise, then install the knobs with the pointer to “0.”