TROLEX TX6831 AV Alarm Instruction Manual
- June 16, 2024
- Trolex
Table of Contents
TROLEX TX6831 AV Alarm
PRINCIPAL OPERATING FEATURES
- Compact and strong polycarbonate housing.
- Self contained construction saves cost of installation and cabling.
- High intensity LED all-round visual flashing alarm with 85dB audible sounder.
- Confidence blip at 15 second intervals.
- Choice of input signal; Contact state or analogue.
- 4…20mA or 0.4…2V analogue compatibility with user adjustable alarm trigger setpoint.
- Certified intrinsically safe to CENELEC standard for use in Group I hazardous areas.
- Versions with visual alarm only.
DIMENSIONS
Enclosure Drilling Details
ALL DIMENSIONS IN MM
- Max. insertion from inner wall of enclosure 10mm + wall thickness (T).
- Min. insertion from inner wall of enclosure 7mm + wall thickness (T).
TECHNICAL DETAILS
Light Source: | High intensity LEDs. |
---|---|
Input Signal: |
- Contact state. CLOSE or OPEN for alarm.
- Analogue signal with potentiometer adjustable setpoint for UNDER or OVER alarm.
Audible Alarm:| High intensity audible sounder 85dB @ 1 metre (12V dc).
Alarm Indication:|
- 1/ sec flashing visual with optional audible alarm.
- Confidence blip at 15 second intervals.
Alarm Signal Out of Limits:| Alternating LED flash with double sounder
‘beep’ (when fitted).
Hysteresis:| 5% of setpoint.
Housing Material:| Polycarbonate.
Protection Class:| IP65 (Sounder: IP54).
Net Weight:| 100gms.
ELECTRICAL DETAILS
Supply Voltage: 7.5…16.5V dc
Power Consumption: 15mA (mean). 75mA peak during LED flash state.
Analogue Input Signal: 4…20mA / 0.4…2V options.
State Input Signal: (low): 0V min. 1.1V max. (high): 1.3V min +Supply V
max.
Connections
Ensure that the unit is set up correctly.
The TX6831 Audio/Visual Alarm must only be
interconnected with approved power supplies, signal sources and monitoring
equipment when used in hazardous areas.
Connecting intoa 4…20mAsignal loop.
REMOTE MONITORING DEVICE
ONLY THE AUDIO/VISUALALARM IN THELOOP
Connecting to a 0.4…2Vsignal source.
Volt-free input contact.
5V State input.
SETUP
TYPE OF INPUT SIGNAL
**A**
4…20mA Analogue Input| 0.4…2V Analogue Input| 5V State Input| Contact State
Input
---|---|---|---
OFF| OFF| ON| ON
ADJUSTING THE SETPOINT
- The setpoint can be setup empirically by adjusting the SETPOINT potentiometer.
- For more accurate setup, connect an approved test instrument (0…2V) to the TEST POINT and adjust the SETPOINT to the desired level.
0.4V 4mA 0.4V
2V 20mA 2V
ALARM SETPOINT MODE
B
Analogue Input | Analogue Input | Voltage Free Contacts |
---|---|---|
Alarm on rising signal = OFF | Alarm on ‘high’ level = OFF | Alarm on contacts |
closing = OFF
Alarm on falling signal = ON| Alarm on ‘low’ level = ON| Alarm on contacts
opening = ON
APPLICATION
-
ATX6373 Gas Sensor fitted witha TX6831 Audio/Visual Alarm (4…20mA)
- A 2-way terminal block will be required within the termination chamber in order to connect to the 4…20mA loop.
-
ATX5921 Vortex Air Flow Sensor fitted witha TX6831 Audio/Visual Alarm(4…20mA)
- The TX6831 Audio/Visual alarm uses the same power supply connections as the TX5921 Vortex air flow sensor.
CERTIFICATION & APPROVAL
Certified IS to Euro norm Standards
- EEx ia I IMI
Designed to comply with
A T E X
- ATEX directive (94/9/EEC)
- EMC directive (89/336/EEC)
SPECIAL CONDITIONS FOR SAFE USE
The internal temperature of this equipment may rise above 150°C under normal or fault conditions, therefore, care shall be taken when the enclosure is opened to ensure that no dust enters the equipment.
PROTECTING THE ENVIRONMENT
Many of our products are often used to monitor the quality of environmental conditions consequently Trolex is also particularly aware of the need to protect human health and the environment in which we live.
The Company has instituted a radical environment protection policy to ensure that all aspects of our manufacturing programme have the minimum possible detrimental impact on the environment. This covers all stages beginning with sustainable product design supported by careful selection of the materials used in their production, through to managed recovery and disposal at the end of the useful life of a product.
This policy also incorporates the principles of the Waste Electrical and Electronics Equipment (WEEE) directive, and the associated Restriction of Hazardous Substances (RoHS) directive, to be implemented in EU countries.
Progress is already well advanced on the introduction of a completely new range of products that maximise the central principle of sustainable design with the intention of reducing the end-of-life cost to the end user.
All Trolex products are manufactured to exacting standards in accordance with our stringent quality control ethos. Having chosen to use one of our products will, in itself, guarantee extended durability and a long operating life, endorsed by our commitment to recycling and recovery.
- All packaging materials are carefully selected to be bio-degradable or re-cycle able where possible.
- All plastic materials are identified for recycling purposes and re-cycled materials are used where it is possible to do so.
- Printing paper and material are sourced from suppliers that have a declared environmental management system.
- Product design centred around high quality and long term durability. Modular architecture both in construction and software design suitable for future upgrades and adaptability to alternative duty.
- Ease of product disassembly, minimisation of fixing devices, and clear separation of functional parts to benefit re-use and re-cycling.
- Control and monitoring of suppliers of components and sub-assemblies. Deal only with suppliers that have a defined commitment to environmental monitoring principles.
- Control the use of restricted substances within the design process. Deal only with suppliers that have a defined commitment to the control of restricted substances.
- Provide an efficient high speed service within Trolex for repair, refurbishing and conversion of products for alternative duty.
- Provision of an end-of-life product Take-back service for recovery, re-use, and recycling of electrical and electronic components. Retain the packaging of a new product and re-use it to return the device to us at the end of its working life. Trolex will guarantee to recover all materials and components, where practicable and arrange for them to be re-cycled in an appropriate and in a safe manner.
CUSTOMERS SUPPORT
TROLEX LIMITED
NEWBY ROAD, HAZEL GROVE, STOCKPORT,
CHESHIRE SK7 5DY, UK
+44 (0)161 483 1435
sales@trolex.com
www.trolex.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>