HOTOOK Full Touch RGB Remote Control Instruction Manual
- June 15, 2024
- HOTOOK
Table of Contents
Operation Instructions of full touch RGB remote control
Specifications
Working temperature: -20 – 60 ˚C
Dimension: L113W55H22 mm
Net weight: 90 g
Working voltage: 4.5V (AAA*3)
RF frequency: 2.4 GHz
RF distance: 20 m
Control Method:
The function of each button as below:
| Name of key | Instruction | Remarks |
|---|---|---|
| OFF | OFF in any time | |
| PAUSE | Pause/Run for dynamic modes | |
| Mode | The mode will go to next, when you touch the key | 9 modes in total |
| Speed/Brightness + | The Speed/Brightness will +1, when touch the key each | |
| time | Speed for dynamic modes, Brightness for static modes | |
| Speed/Brightness – | The Speed/Brightness will -1, when touch the key each time | |
| Color Ring | For static color selection |
9 modes in total as below:
| No. | Patterns | No. | Patterns |
|---|---|---|---|
| 1 | Static white | 6 | Seven-color gradient changing |
| 2 | White breath | 7 | R/G cross fade |
| 3 | Three-color jump changing | 8 | R/B cross fade |
| 4 | Seven-color jump changing | 9 | G/B cross fade |
| 5 | Three-color gradient changing |
RF CODE
(3.1) Code pairing operation: means that the receiver will only be controlled by the value code remote control.
| Step | Operation | Instructions |
|---|---|---|
| 1 | Connecting the load to the receiver and power on it. | 1.1 It is necessary |
to clear the code rst, if the receiver was coded before.
1.2 Batch operation can be performed within the remote control range.
2| Press and hold “PLAY/PAUSE” on the remote control for 5 seconds, the
indicator of the remote control will ash quickly, means it enters the pairing
code transmission status.| Will automatically exit code transmission status
after 60 seconds, or pressing any key to exit.
3| See the load light ashes 3 times and return to the initial state.| Pairing
coding is nished successfully.
(3.2) Code clearing operation: means that the original code value of the receiver will be cleared and returned to the factory state. Then it can be controlled by any compatible remote control, and can learn to a new code.
| Step | Operation | Instructions |
|---|---|---|
| 1 | Connecting the load to the receiver and power on it. | 1.1 tne |
cıearing operation snouıd be finisned witnin 1 minute after tne receiver
is powered on. ıf exceeds the time, can be powered on again.
1.2 batch operation can be performed within the remote controı range.
2| Press and hold the remote control “ON/OFF” for 5 seconds. The indicator of
the remote control ashes quickly, means it enters the clearing code
transmission status.| 2.1 wiıı automaticaııy exit code transmission status
after 6o seconds, or pressing any hey to exit. ıf the originaı remote controı
is ıost, the new
2.2 remote controı can be used for cıearing operations.
3| See the load light ashes 3 times and return to the initial state.| cıearing
coding is finished successfuııy.
(3.3) Code learning operation between remote controls: Used to unify system code values or copy a new remote controls. Since each remote control has its own unique code at the time of delivery, when there are multiple remote controls in one system, one of them (for example, remote control A) must be selected as the system code value, and the code value of the rest remote controls (for example, remote control B) should be copied to the same one.
| Step | Operation | Instructions |
|---|---|---|
| 1 | A remote controı: press and hoıd “playıpause” on the remote controı for 5 |
seconds, the indicator of the remote controı wiıı fıash quichıy, means it
enters the pairing code transmission status.| will automaticaııy exit code
transmission status after 6o seconds, or pressing any hey to exit.
2| B remote controı: ıong press “mode” for 5 seconds, the remote indicator
ıight changes from 1oo% ıight to off ıight, means entering the code vaıue
receiving state| wiıı automaticaııy exit the code vaıue receiving state after
зo seconds, or exit after ıearning the code vaıue successfuııy.
з| see the b remote controı indicator ıight fıash з times.| Code copying is
finished and exit code vaıue receiving status.
| Step | Operation | Instructions |
|---|---|---|
| 1 | long press “mode” for 2o seconds. | the remote indicator ıight dim down and |
fıashes continuousıy untiı the 2oth second and then bach to 1oo% ıight. means
this step is finished.
2| press the “onıoFF” to confirm, the remote indicator ıight fıashes з times.|
Restore factory settings successfuııy.
Attention
- In order to extend the life of the battery, the remote control will enter sleep mode without any operation for 10 seconds, please pressing any key to wake up it before using.
- The signal of the touch ring/buttons is continuously transmitted for a maximum of 30 seconds, please release it and operate again if times out.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>