Maxxima MEL-6150DW Luvoni Smart WiFi LED Outdoor Wall Light Installation Guide

Maxxima MEL-6150DW Luvoni Smart WiFi LED Outdoor Wall Light Installation Guide

WARNING:

1. To avoid fire, shock, or death, disconnect power at circuit breaker or fuse before the installation.
2. If you are unsure about the installation or maintenance of the Outdoor Lights, please consult a qualified electrician.

SAFETY

1. Please read all warnings and instructions before installation.
2. The fixture must be wired in accordance with the National Electric Code and applicable local codes or ordinances.
3. To insure personal safety, proper grounding is required.

INSTALLATION NOTES:

1. This fixture should not be used in areas with limited ventilation or high ambient temperature exceeding 40°C.
2. Fixture cannot be used with a dimmer switch, motion sensor and other electronic switching devices.

INSTALLATION LOCATION:
This fixture must only be wall-mounted. Be certain that the receiving junction box is well secured and can support the weight of the lamp.

PRODUCT DIMENSIONS

PRODUCT SPECIFICATION

• Part Number: MEL-6150DW
• Input Voltage: 120 VAC
• Amp Draw: .094 A
• Frequency: 60 Hz
• Rated Power: 11.5 W
• Suitable for: Wet Locations

INSTALLATION INSTRUCTION

CAUTION: Read WARNING and SAFETY Notes before beginning installation
Please refer to Figure 1 and Figure 2 while following installation instructions.

1. Make sure POWER is turned OFF at the circuit breaker box or remove fuse.

2. Carefully disconnect and remove the old light fixture if applicable.

3. Using the (Qty. 2) CROSSBAR SCREWS provided, mount the CROSSBAR BRACKET into the JUNCTION BOX.

4. Locate and retrieve the supply wires from the JUNCTION BOX.
   a. Connect the white wire from the fixture to the NEUTRAL wire in the JUNCTION BOX (typically white).
   b. Connect the black wire from the fixture to the HOT wire in the JUNCTION BOX (typically black). c. Connect the Green/Yellow wire and Bare copper wire to the Bare copper wire in the JUNCTION BOX. If the Bare copper wire is not present in the JUNCTION BOX, connect it to the GROUND SCREW on the CROSSBAR BRACKET which must be connected to GROUND for safety.

5. Adjust the UPPER CROSSBAR to be in a horizontal position and securely tighten both CROSSBAR SET SCREWS.

6. Insert the (Qty. 2) MACHINE SCREWS on the UPPER CROSSBAR through the holes in the FIXTURE BASE and tighten by using the (Qty. 2) CAP NUTS. Make sure that the fixture is tightly secured against the wall. If the fixture is loosely mounted or if the CAP NUTS cannot be tightened completely, it can be fixed as follows:
   The (Qty. 2) MACHINE SCREWS on the UPPER CROSSBAR can be adjusted by loosening their nuts (not seen in figures above) and then screwing them in or out to alter the length of MACHINE SCREWS sticking out from the UPPER CROSSBAR. Once the adjustment appears correct, lock the MACHINE SCREWS in place with their nuts and then secure the fixture tightly against the wall by using the (Qty.

2. CAP NUTS.

7. Turn power ON at circuit breaker (or replace fuse) and confirm that the fixture is functioning properly. If the light is not on, press the WiFi Set Button to turn the Light on. Press the WiFi Set Button a 2nd time to turn the light off.
8. Once functionality is confirmed, consider use of waterproof glue or silicone caulk to seal the FIXTURE BASE to the wall surface to ensure that the fixture is completely waterproof, If water enters the junction box, it may damage the fixture and/or building/residence.

Mobile APP Set-up

Step 1
Download the”Smart Life” App

• Scan the QR code below to download the “Smart Life” App
• You can also download this app in the App Store/Android App Market, search “Smart Life”

Step 2
Register an account and Login

• Open the Smart Life App, click Register to create an account & login.
• If already registered, login.

Step 3
Selecting the Device

• Click ‘Add Device’ or the ‘+’ in the top right-hand corner;
• Click ‘Lighting’ then ‘Light Source (Wi-Fi)’ to enter the device connection interface.
  

Step 4
Mobile phone connection

Step 4a
EZ mode connection:

When the Outdoor Light is on, hold the WiFi Set Button until the light flashes once, then release the button. Press the WiFi Set Button once and the light will flash quickly (flash once every second), your device can connect to the light. The light will stop flashing once when the connection is successful. If there is no connection, device will exit network configuration mode after 3 min.

• Enter the Network Name & WiFi password for your home, click Next.
• Confirm the light is flashing,click device indicator is ‘fast blinking (0.5S/time)’.
• Device will Connect.
  

Step 4b
AP mode connection:

When the Outdoor Light is flashing quickly; hold the WiFi Set Button until the light turns solid, then release the button. Press the WiFi Set Button once and the light will flash slowly (flash once every 2-3s), your phone can connect to the light. The light will stop flashing once when the connection is successful. If there is no connection, the device will exit network configuration mode after 3 min.

• Enter the Network Name & WiFi password for your home and click Next.

• Confirm the light is flashing slowly. Click “Blinking or breathing slowly”

• Back out of the app and go to your device’s Wifi settings. Connect to the light’s WiFi hotspot: “Smartlife-XXXX”

• Return to the Smart Life App and wait for the connection to complete.
  

• Click to enter the operation interface.

Mobile APP operation

• Select White to adjust the CCT and to Dim.

• Select Color to adjust to the desired color, to Dim and adjust Contrast.
  

• Click Schedule to set a on or off function of the light at a certain time/day(s).

• Add schedule and then save. Repeat as desired.
  

• Select Left Time to enable Countdown Timer when light is on. The time selected will automatically turn the light off after the desired time.
  

• After the light connection is completed, it can be shared to many people, that is, one light can be controlled by multiple Users.

• Click to enter the device details interface;

• Click ‘Share Device’ to enter the device sharing interface.
  

• Click ‘Add Sharing’, add the account you are willing to sharing.
  

• You may also share all devices in your account with another account

• Go to “Me” at the bottom of the App

• Select “Home Management”

• Select the Home you wish to share with

• Select “Add Member”. You can send the invite via your Smart Life account, Message, or Email. New Members must have or create a Smart Life account via the Smart Life App

BlueTooth capability Instructions

When the smart light loses connection to the network, they are unable to be controlled by the app. After 3-5 minutes, the smart lights will automatically switch to Bluetooth control mode. In this mode, the light can still be controlled by a phone at a short distance via bluetooth.

Note:  Make sure Bluetooth is enabled on your phone.

1. Make sure the product is paired with your mobile phone on the app
2. Keep your phone connected to the internet

Support Amazon Alexa and Google Home Set-up

For Amazon Alexa

• Open the Alexa app and select “Skills” from the top menu
• On the Skills page, search for Smart Life
• Enable Smart Life in the Alexa App
• Log in with your Smart Life Account (username & password)
• Discover new smart devices in the App or ask Alexa to discover new devices

For Google Home

• Open the Google Home App and tap the “+”icon in the homepage
• Select “Set up device” in the “Add and manage” Screen
• In the “Set Up” screen, tap “New Devices” to set up new devices in your home
• Tap “Works with Google” to authorize Google Home to work with your Smart Life account

ZAmazon Alexa and Google Home voice control examples

For Amazon Alexa

• Alexa, turn on
• Alexa,turn off
• Alexa,set to percent
• Alexa, brighten/increase
• Alexa,dim/decrease

For Google Home

• Hey Google,turn on
• Hey Google, turn off
• Hey Google,is on/off?
• Hey Google, brighten/increase <device name)
• Hey Google, Dim/Brighten by 50%

Trouble-Shooting/Recommendations / Tips

• If the light is offline in the App, make sure the in-wall switch is in the On position. If not, turn on. Please check whether the light is connected with power, and your mobile device is connected to a 2.4GHz WiFi Network.
• Check the router. If the router is dual-band, make sure to select 2.4GHz network to add the light. Router Broadcast should be set to open. Also try disabling the 5GHz band temporarily on the router.
• Make sure the WiFi User Name and Password are correct.
• Make sure the light is within the range of the router signal. If not, try moving closer to the router. Check Wi-fi signal on the mobile device to make sure the signal is strong in that area or if it is weak.
• Check to see if the maximum number of devices/lights the router can handle has been reached. If so, remove a device/light and restart the router. If there is no Wi-Fi connection, try restarting the light and/or restarting the router.
• If the device will not go into pairing mode, try the on/off sequence 4 or 5 times instead of 3 times. Also give a second or 2 longer delay between the on/off sequence.
• If the internet signal/connection from the internet provider is down, the light can still be controlled through the mobile device as long as both are connected to the same Network (Intranet).
• If the internet signal/connection is down from your router, this light has a backup bluetooth function that will allow you to control the lights from a certain distance. Ensure bluetooth is enabled on your device.
• For additonal troubleshooting tips, visit the webpage listed below https://www.maxximastyle.com/wifi-help

3 YEAR WARRANTY
Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation whatsoever beyond sending a free replacement product.
info@maxximastyle.com
866-ΜΑΧΧΙΜΑ (629-9462)
www.maxximastyle.com
125 Cabot Court Hauppauge, NY 11788

References

• Factory Direct LED Recessed Lighting, Outdoor Wall Lights, Ceiling Fixtures and Electrical Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>