Roco 7500040 Electric Locomotive Instruction Manual

Roco 7500040 Electric Locomotive

Product Information

Specifications

• Model: H0-Modell: Elektrolokomotive BR 193, SIEMENS
• Manufacturer: Modelleisenbahn GmbH
• Model Numbers: 7500040-920 I/24, 7500040, 7520040, 7510040

Product Usage Instructions

Inbetriebnahme Ihrer Lokomotive (Starting locomotive operation)

Auspacken des Modells (Unwrap model): Take out the model cautiously with foil (Fig. 1).

Schleiferwechsel (Pickup replacement)

To replace the pickup, refer to Fig. 11.

Wartung und Pflege des Modells (Maintenance of the model)

Haftreifenwechsel (Traction tire replacement)

To replace the traction tires:

1. Remove the gearbox cover first (Fig. 5).
2. Then remove the wheelset and pull off the traction tires using a needle or a fine screwdriver (Fig. 7).
3. When putting on the new traction tires, make sure they do not twist.

Zusammenbau (Assembly)

Please pay attention to the correct position of the contacts during assembly.

Starting locomotive operation

Unwrap model

Take out the model cautiously with foil (Fig. 1).

Operating instructions

Before use, it is advisable to let the loco go around about 30 minutes forwards and 30 minutes backwards without load to obtain an optimal circuit and best tractive power. The smallest radius that this model should run is R2 of the ROCO track system (R2 = 358 mm). Your locomotive will run smoothly on clean tracks only. Forcleaning, we recommend using item no. 46400, Roco track cleaning van, or item no. 10002, Roco track cleaning rubber, for removing heavy dirt.

Fittings

Operation is possible with different couplings (Fig. 2). We recommend using the Roco close coupling. In the enclosed accessory bag, you will find small kits to be fitted on your locomotive. Please mount them cautiously. Attention! Use glue only if indicated (Fig. 2+3).

Running in digital mode

Remove the jumper from the interface. Finally, put the plug of the chip into the interface as shown in Fig. 8. Attention! On models with train destination display, their lighting as well as the high beam function cannot be switched in analogue operation!

Starting locomotive operation

Unwrap model: Take out the model cautiously with foil (fig. 1).
Operating instructions: Before use is advisable  to let the loco go around about 30 minutesforwards an 30 minutes backwards without load, to obtain an optomal circuit and best tractive power. The smallest radius this model should run is R2 of the ROCO track system (R2 = 358 mm). Your locomotive will run smoothly on clean tracks only. For this purpose we recommend using item no. 46400, Roco track cleaning van, or item no. 10002, Roco track cleaning rubber, for removing heavy dirt.

Fittings: Operation is possible with different couplings (fig. 2). We recommend using the Roco close coupling. In the enclosed accessory bag you will find small kits to be fitted on your locomotive. Please mount them cautiously.
Attention! Use glue only if indicated (fig. 2+3).
Running in digital mode: Remove the jumper from the interface. Finally put the plug of the chip into the interface as shown in fig. 8.
Attention! On models with train destination display, their lighting as well as the high beam function cannot be switched in analogue operation! A.C. pick up: see fig. 11

Maintenance of the model

To enjoy your model for a long time, it is necessary to service it regularly (i.e. after it has been in op-eration for approximately 30 hours).

1. Cleaning of wheel contacts: Wheel contacts easily get dirty on tracks that are not en-tirely clean. Use a small brush to remove dirt from spots marked in fig. 6. Prior to cleaning the contacts dismantle the bogie (fig. 5).

2. Lubrication : Apply tiny oil drops to spots marked in fig. 9. Prior to lubrication dismantle locomotive (fig. 4). We recommend using item no. 10906, Roco oiler. For lubrication the gearparts (e.g. cogwheels, worm) we whould recommended our Roco special grease (item no. 10905). Attention: Please do not oil these parts when using our grease.

3. Change of traction tyre: Remove the gear cover (fig. 5). Take out wheel set and remove traction tyre using a pin or a fine screwdriver (fig. 7). When pressing on the new traction tyre please avoid twisting it.
   Motor Changing: First remove loco body (fig.4) and then change the motor (fig. 10).

4. Assembly: During assembly please take care of correct position of contacts.

Dip-Switch for analog model 7500040

1. Position “ON”
   Works setting: The headlight is illuminated in the analog and digital operations, depending on the direc-tion of travel.

2. Position „OFF“
   In the analog operation, the headlight is deactivated.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>