SIGNSTEK ST-200DF Fingerprint Door Lock Installation Guide

SIGNSTEK ST-200DF Fingerprint Door Lock

Package Contents

Preparation

• Tools needed: screwdriver, tape measure, pencil

Installation

• If there is a drilled hole for the lockset on the door, go to STEP 3

Mark the door with a template

• Measure the dimensions from the door edge to the centre of the hole on the door face.
• Use the TEMPLATE as an indication to mark the centre of the circle on the door face and the centre of the door edge.

Drill Holes

• Measure the dimensions from the door edge to the centre of the hole on the door face.
• Using the marks as a guide to drill a hole 02-1/8″ (54 mm) through the door face for the lockset, then a hole of 01″ (25.4 mm) for the latch.

Adjust Latch if needed
Measure the dimension as shown. If the measurement is 23/4′ (70mm), please adjust the latch.

Latch Adjustment

• Determine if the latch needs to be adjusted to the 2-3/4″ (70 mm) backset.
• To adjust, rotate the latch until it stops.
• Reverse the direction to return to the 2-3/8″ (60 mm) backset.

Change the Latch Face if needed and install the latch

Note: The latch/bolt must remain retracted during installation.

Install the strike into the door frame

• To identify the centre of the strike: close the door to lay the latchbolt against the door frame. Mark the centre line on the doorframe exactly opposite the latch hole in the door edge.
• Measure one-half of the door thickness from the door stop and vertically mark the centre line of the strike. Drill 1″ (25.4 mm) hole, 1″ (25.4 mm) deep at the intersection of the horizontal and vertical line of strike.
• Chisel 5/64″ (2 mm) deep along the strike outline to allow the strike to be aligned with the doorframe.
• Install the strike plate into your door frame and tighten it with wood screws.

Identify door handling and install the keypad
For left-handed doors or right-handed doors, the tailpiece must be vertical when installed.

Install the keypad

• Install the front panel and front panel silicon pad to make sure the latch bolt is contracted.

• Note: Cylinder bolt must be Vertical!
• The bolt must remain retracted throughout installation!
• Install the mounting plate with screws and make sure it is paralleled with a keypad and door edge.

• Pay attention to the direction of the connector when inserting the connector

NOTE: Keep the knob vertical and the concave point upward when installing.

Fingerprint Identification

• Advanced biometric sensor, the most secure fingerprint authentication.
• For security reasons, Signstek will only accept fingerprint patterns that consist of cross-intersection points. Patterns with no cross-intersection points will not be acceptable.
• Please check your fingers before registration to make sure the finger you want to register will be acceptable by our system. Otherwise, use an alternative finger to ensure successful registration.
• The following examples show which types of fingerprint patterns will be acceptable.
• The following examples show which types of fingerprint patterns will be acceptable.

Fingerprint Scanning Directions
The following directions and tips will guide you on how to scan an optical fingerprint.

Correct

Incorrect

Fingerprint Scanning Tips & Troubleshoot

Tips for Fingerprint Enrollment and Recognition

• Place your finger to completely cover the sensor with maximum contact surtace.
• Position the centre of your finger (core) to the centre of the sensor.
• Hold your finger still for more than a second until you hear a beep.
• Scan a finger that is clean and free from dirt. If a finger is cracked and dry, lightly moisten the finger to improve recognition.
• Children under 12 are not recommended to use fingerprint access due to the constant changes of their fingers during growth.
• The elderly with fading fingerprints may have difficulty in recognition.
• If your finger has a cut, scar, or cracked skin due to dryness, try another finger.

Troubleshooting Fingerprints
In case of poor fingerprint conditions

• WET – wipe excess moisture from the finger before scanning.
• DRY- moisturize or blow warm breath over the finger before scanning.
• DIRTY – wipe stains and dirt off from your finger before scanning.
• Make sure the sensor is clean from dirt or smudges – wipe the sensor with a soft cloth regularly.

Programming Guide

Administrator Code (AC) User Code (UC)

How to use?
Unlock from outside

Unlock from inside

Lock from outside
Manual lock the door mode

• The default setting is to close the door manually.
• Keep pressing any key for 2 seconds.

Auto-lock mode

• With auto-lock mode on, the bolt will extend out automatically in the set time after unlocking.
• Default Administrator Code: 000000 (AC must be 6 digits in length)
• Default User Code: 1234 (UC must be 4 digits in length) ale program the lock while the door is open
• A Pist after installation or resenting default selling

Lock form inside

Manual lock the door mode

• Rotate the thumb turn piece to the lock position.

Auto-lock mode

• With auto-lock mode on, the bolt will extend out automatically in the set time after unlocking.

Door Handing Identification Process:

Note: For new installation or restoring default setting, you must run the door handing identification process with the bolt contracted first.

Change Administrator Code:

Add User Codes:

Note: Up to 9 sets of User Codes can be saved. After user codes are added, the default User Code will be invalid.

Change User Code:

Delete User Code:

Delete All User Codes:

Toggle Mute Mode On/Off:

• Repeat the same steps to turn the beeper on.

Enable/Disable All User Codes:

Note: When all User Codes are disabled, no User Codes can unlock.
You can only insert the key and turn it to unlock. Repeat the same steps to enable all User Codes.

Create One-time User Code:

Note: The one-time user code will be automatically invalid after one use.

Toggle Manually Lock the Door Mode On/Off:

Note: The default setting is to close the door manually. When the door is unlocked, you can directly press any key for 2S to lock the door. After this function is turned off, you can only lock the door with the key or turn on the auto-lock function. Repeat the same steps to toggle manually lock the door mode on.

Toggle Auto-lock Mode On/Off:

Note: Default is off. Once turned on, the default auto-lock delay time is 30S. If you want to change the auto-lock delay time, please refer to the setting of the auto-lock delay time. To disable the auto-lock function, please repeat the same steps.

Set Auto-lock Delay Time:

Add User Fingerprint:

Note: Up to 100 fingerprints can be saved. After 5 acquisitions, the green light will be on for 4 seconds you will hear a long beep.

Delete User Fingerprint(delete by serial number):

Note: For example, the first registered user fingerprint ID is 1.

Delete User Fingerprint (search delete) :

Note: 1 green light + 1 long beep = collect successfully; 1 red light + 1 short beep = fail to collect

Delete All User Fingerprint:

Restore Default Settings

• Take off the battery cover, and insert a pin into the reset hole next to the batteries to press the reset button for 5 seconds.
• You will hear 3 long beeps and the # flashes blue light 3 times, which will indicate the restoration is completed.

Explanation of special functions

1. Security protection: If you enter incorrect passwords continuously five times, the keypad will be locked for 1 minute, and the system will make no response within 1 minute and automatically unlock after 1 minute.

Operation Indicator Sounds and Lights

Specification parameter

Warranty

• 1-year warranty from the purchase date. If you have any questions, feel free to contact us.
• This limited warranty does not cover human-made damage; the appearance was artificially stained, scratched, broken, stains and so on.
• This limited warranty does not cover any damage, deterioration or malfunction resulting from the repair or installation of this product by anyone unauthorized by us.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>