LINSY HOME LH022Y2-A Book Shelfs and Bookcases Instruction Manual

LINSY HOME LH022Y2-A Book Shelfs and Bookcases

Product Information

The product model is LH022Y2-A / LH022Y2-B. These are assembly instructions for the product. Please read these instructions carefully before assembling the product. The instructions include safety and care advice, a list of components and tools, and general care and maintenance information.

Safety And Care Advice

• Check if all the components and tools listed on pages 3 – 4 are received.
• Remove all fittings from the plastic bags and separate them into homologous groups.
• Keep children and animals away from the working areas as small parts may cause suffocation if swallowed.
• Ensure you have enough space to lay out the parts before starting.
• Do not stand on the product, as it could cause damage.
• Assemble the product as close to its final position as possible.
• Do not place furniture directly in front of radiators, fires, or any other source of heat.
• The assembly will be easier with 2 people.
• Dispose of all packaging carefully and responsibly.

General Care and Maintenance

To maintain the product, follow these general care and maintenance guidelines:

• Follow the assembly instructions carefully.
• Keep the product clean by wiping it with a damp cloth.
• Avoid using abrasive cleaners or solvents that may damage the surface.
• Regularly check and tighten any loose screws or fittings.

Product Usage Instructions

Assembly Instructions

Before starting the assembly, check if all the pieces listed below are received:

• A: Black Plastic Top Cover
• B: Middle Panels x 3pcs
• C: Short Panels x 4pcs
• D: Long Panels x 2pcs
• E: Top Brackets x 3pcs
• F: Bottom Brackets x 3pcs
• G: X-bar
• H: Short Reinforcement x2pcs
• I: X-bar Long Reinforcement x2pcs
• J: Nails x 21pcs
• K: M6x25 Screws x 41pcs
• L: M6x10 Screws x 15pcs
• M: Nuts x 3pcs
• N: Large Back Panel x 2pcs
• O: Leveler Feet x 6pcs
• P: Allen Key x 1pcs
• Q: Spanner x 1pcs
• R: Small Back Panel x 2pcs
• S: Furniture Anchors x 2pcs

Assembly Steps

1. Stand the brackets sideways on the ground. Install the long panels by locking screws according to hole position.
2. Keep the screws in the same direction at its installation.
3. Fasten the nails to the panels by hammer or drill.
4. Fasten x-bar reinforcement by screws. In particular, the intersection of the x-bar reinforcement should use the screws J and the nuts K.
5. Insert the top brackets into the bottom brackets then fasten with screws.
6. Install the short panels and middle panels in order.
7. Install the leveler feet.
8. If the product is not stable, adjust the leveler feet.
9. Install the furniture anchors by drilling holes on the wall and attaching them to the leveler feet based on needs.

Safety And Care Advice

Important – Please read these instructions fully before starting assembly.

• Please check if all the components and tools listed on pages 3 – 4 are received.
• Please remove all fittings from the plastic bags and separate them into homologous groups.
• Please keep children and animals away from the working areas; swallowing small parts may cause suffocation.
• Please make sure you have enough space to lay out the parts before starting.
• Do not stand on the product, which could cause damage.
• Please assemble the product as close toits final position as possible.
• Do not place furniture directly in front of radiators, fires, or any other source of heat.
• The assembly will be easier with 2 people.
• Please dispose of all packaging carefully and responsibly.

General care and maintenance.

• Please clean with a damp cloth or mild detergent, do not use bleach or abrasive cleaners.
• Do not allow the spill to stay on the surface for a long time.
• Do not clean with products containing the following: acetone (e.g., nail varnish remover), ammonia (e.g.bleach), or sodium hydroxide(e.g., caustic soda, drain, and oven cleaners).
• If the product is accidentally exposed to the irritating liquid, rinse thoroughly with clean wate.r Mats can be used to protect surfaces from moisture and heat.
• Please check whether there are missing screws in the product regularly.
• The product should not be discarded with household waste, and please take it to your local authority waste disposal center.

Components

Please check if all the pieces listed below are received.

Assembly Instructions

Please check if all the pieces listed below are received.

Plea se use the s crews correctly, otherwise, the product will be seriously damaged!

Step 1

Stand the brackets sideways on the ground. Install the long panels by locking screws according to hole position.

Keep the screws in the same direction at its installation

Step 2

Fasten the nails to the panels by hammer or drill.

Step 3

Fasten x-bar reinforcement by screws.
In particular , the intersection of the x-bar reinforcement should use the screws J and the nuts K.

Step 4

Insert the top brackets into the bottom brackets then fasten with screws.

Step 5

Install the short panels and middle panels in order.

Step 6

If it is not stable,adjust the leveler feet.

Step 7

Install the furniture anchors by drilling holes on the wall and the leveler feet based on needs.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>