Radioddity Raddy L7 LoRa Weather Station User Guide

Radioddity Raddy L7 LoRa Weather Station

Product Information

Weather Server Registration Guide

Note: If you have registered the Weathercloud and underground account before, only need to create New Device to add your new weather station information.

Sign up on Weathercloud.net

Note: You are advised to register on the laptop for better experiences.

1. Click the “Create device” button
2. Visit the https://www.weathercloud.net website and sign up
3. All the red star (*) blanks need to be filled in
4. Note: Select any name or other in the Model list and any link type
5. Input any name
6. Input local address
7. Select any model or other in the link type
8. Sign in to Weathercloud with Email and Password
9. Click “Get Coordinates” to identify your location
10. Click the “Create” button at the bottom to save and complete

Sign up on Wunderground.com

1. Click “Settings” and select the link
2. Copy and record the Weathercloud ID and Key information
3. Visit the https://www.wunderground.com website, and click the “Join” button
4. Fill in with Email and Password
5. Sign in with Email and Password
6. Click “My Profile” and select “MY DEVICES” to Add New Devices
7. Note: Select any model or other in PWS DropDownList, then click”Next”
8. Select or input your Local address
9. Input any name
10. Select any model here
11. No need for selection here
12. Click “Next”

WiFi Setup of Display Console

1. Plug-in Adapter and Power up the Console.
2. Make sure the WiFi icon is flashing.
3. Open the WiFi list of your Laptop and select WLAN of L7. (This network does not require any password, you can connect directly. If  you are unable to connect, check if your firewall stops uunfamiliar networkconnections.)
4. Data Uploading: L7-F21780
5. Note: When powering up the console, If the WiFi is displayed without flashing, press the Min/Max key for 3 seconds until the WiFi word icon is flashing.
6. Click “I Accept” and “Next”
7. Copy and Record the station ID and Key
8. Once WLAN is connected, enter the following IP address into any internet browser’s address bar: http://192.168.5.1 to access the console’s web interface (make sure you include the header http://, not just 192.168.5.1).
9. Copy and Paste ID and key information from WU or WC website. Fill in all the other blank tables and save.
10. Note : Once WiFi is connected and data is being uploaded, the WiFi and weather data uploading icons stay solid.
11. Note : Sometimes you need to wait about 30 minutes to see the updated data online.
12. Click the “Save” key and Status display the connected IP, then the connection is completed and you can view the data on WU or WC website.

Quick Setup Instruction

This instruction helps you verify whether the unit is working properly after unboxing.

1. Install Batteries for Outdoor Sensor Array:

   • Remove the battery door on the back of the sensor by removing the set screw
   • Inserting 3xAA batteries in the battery compartment
   • Close the battery door and Tighten the set screw. The sensor LED indicator will light for 3 seconds, and then flash once per 16 seconds thereafter. Each time it flashes, the sensor is transmitting data.

2. Plug in the Adapter for Indoor Console:

   • Pull out the stand on the back
   • The Console will instantly display indoor information, and Integrated outdoor sensor data will update on the display within a few minutes. Do not press any buttons until the outside transmitter reports in, otherwise the outdoor sensor search mode will be terminated.
   • When the outdoor transmitter data has been received, the console will automatically switch to the normal mode from which all further settings can be performed. While in the remote search, the icon will be constantly displayed search mode, the…

3. Sensors Verification:
   

   • Put the outdoor sensor array and the indoor console at the same location in
     good ventilating condition.
   1. Verify temperature and humidity. The difference between indoor and outdoor temperatures should be within 4°F/2°C. The difference between indoor and outdoor humidity should be within 10%. Usually, the indoor temperature is a little bit higher than the outdoor temperature due to the warming-up effect of the backlight. Let the unit stabilize for at least 30 minutes.
   2. Verify wind speed and wind direction. Spin the wind cup and the wind vane and make sure the wind speed and wind direction information on display updates.
   3. Verifying Rain gauge. Tip the sensor array back and forth several times. You should hear a “clicking” sound within the rain gauge. Verify the rain reading on the display console is not reading 0.00. Each “click” represents 0.01 inches of rainfall.

4. Outdoor Integrated Sensor Installation:
   

   • Fasten the integrated transmitter to mounting pole brackets with foot-mounting, two ￠3 bolts, and M3 nuts. Tighten the mounting pole to your existing mounting pole with the four￠5 Bolts and M5 Nuts assembly, or fix on the wall with four tapping screw. Please ensure that the outdoor transmitter is fixed particularly tightly, otherwise windy conditions cause the transmitter to shake and thus misread the rainfall data.
     NOTE : Install the sensor array at least four times the distance of the height of the tallest obstruction.

   • Horizontal Installation:

   • Vertical Installation:

Please refer to the user manual for more detailed instructions and troubleshooting information.

References

• Weathercloud | Global network of weather stations
• Local Weather Forecast, News and Conditions | Weather Underground
• Weathercloud | Global network of weather stations
• Local Weather Forecast, News and Conditions | Weather Underground

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>