Signstek ST100 Electronic Door Knob User Guide

**Signstek ST100 Electronic Door Knob User Guide

**

PACKAGE CONTENTS

• Door Lock

• Backup Key

• Latch/Strike Plate Screw

• Spanner

• Wrought Box

• Strike Plate

• Battery (9V 6L) PS: not included in the package

• Spare Screw: 1 Handle Screw

• Before Installation, Please Check The Accessories in the package according to the above list.

Preparation

1. Tool: Screwdriver
2. Power: DC9V 6LRI
3. Disassemble the entire ST-100 electronic door knob in the package into scattered parts.

Attention: Easy to install, just a screwdriver for installation.

INSTALLATION INSTRUCTIONS

Door Lock Step 1. Mark Door

Using template, mark hole on both sides of door at required backset, then mark latch hole on door edge.

Step 2. Drill Holes

Bore a 54mm(2 ’’) hole on door face, then drill 25mm(1’’) hole in door edge to intersect with center of 54mm hole.

Note: Drill 54mm hole from both sides of door to stop wood splintering

Step 3. Install Latch

a. The backset shown on the left is 60mm (2-3/8″).
b. Pull the cam toward right to extend the backset to 70mm (2-3/4″).
c. The backset shown in figure C is 70mm (2-3/4″). Pull the cam back to left will return the backset to 60mm (2 3/8″).

CAUTION: Be sure the latch cam is upright before making any backset adjustment.

Restore Factory Settings

Press the reset key for 6 seconds and then it will beep for 6 times. The programming is complete when it beeps for 3 times and flashes green for 3 times. The administrator code is restored to 0000 and the user code is restored to 1234.

Turn on or off Passage Mode

Passage mode: If you turn on the passage mode, you don’t need to enter any password and just turn the handle to open the door.

Turn on the passage mode: Rotate the knob counterclockwise.

Turn off the passage mode: Rotate the knob clockwise to the top.

Programming Guide

Default Programming Code: 0000
Your new programming codes (PC): —————–
Default User Code: 1234
Your new User codes (UC): —————-

Change Programming Code (PC)

There is only one PC and PC must be 4 digits in length.
PC cannot be the same as the first 4 digits of the user code.

Create new User Code (UC)

The first 4 digits of the user code must not be the same as the programming code.
The default user code will be automatically invalid after setting new user code.
It allows for at most 6 sets of code, and UC can be 4-10 digits in length.

Change User Code (UC)

Delete one User Code(UC)

Delete all User Codes (UC) at Once

Note: The temporary password will also be deleted, and the default user code will be activated after all user codes are deleted.

Toggle Mute On/Off

Repeat same steps to turn on.

Turn Vacation Mode on/off

Vacation mode: All passwords and passage mode will be disabled, and you can only use the backup
key to unlock or turn off the vacation mode and use the correct password to unlock (repeat the operation
to turn vacation mode off).

Create a One-Time code

Create one-time password/temporary code
Note: Only one set of one-time passwords can be set. When the second one is set, the first one will be
automatically deleted. The one-time password can only be used once.

Operation Indicator Sounds and Lights

the vacation mode or use the backup key
Flashes Red 5 Times| 5 Beeps| The system automatically locks when entering wrong code for 5 times| Wait for 1 minutes and the system will restore.
Flashes Red 10 Times| 10 Beeps| Low-battery alarm| Replace 9V battery

Trouble Shooting

When creating new code, enter PC and press 1, and there are 3 beeps and flash red for 3 times| The password has been set up to 6 groups and cannot be added.| Change the user code or reset the lock
The lock can be unlock even if enter wrong code| Passage mode is on| Turn off the passage mode
Forget the programming code| Forget the programming code| Reset the lock
Cannot install the cover of inside lock| The knob is not turned to be vertical| Turn the knob to the vertical direction and then install the cover

Lock Parameters

1. Model ：100
2. Power Supply: DC9V, 6L
3. Installation specifications:
   • Door thickness 1.38inch-1.97inch
   • Door edge   to circle center distance : 2.36inch or 2.76inch (adjustable)
4. Front plate size: diameter 3.15 inch X height 2.8 inch
5. Rear plate size: diameter 3.15 inch X height 2.8 inch
6. Handle size: diameter 2.36 inch X height 2.28 inch

BATTERY INFORMATION

• Must use one 9V alkaline battery not the carbon battery

WARRANTY

Thank you for purchasing our product.

We provide 1-year warranty for the lock.

This limited warranty does not cover human-made damage; the appearance was artificially stained, scratched, broken, stains and so on.

This limited warranty does not cover any damage, deterioration or malfunction resulting from the repair or installation of this product by anyone unauthorized.

PARTS DISCRUPTION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>