SAFEWAZE 020-12101 EVO Detachable Cable Sleeve Instruction Manual
- June 15, 2024
- SAFEWAZE
Table of Contents
SAFEWAZE 020-12101 EVO Detachable Cable Sleeve
WARNING
This product is part of a personal fall arrest system. The manufacturer’s
instructions must be provided to users of this equipment. The user must follow
the manufacturer’s instructions for each component of the system. The user
must read and understand these instructions before using this equipment.
Manufacturer’s instructions must be followed for proper use and maintenance of
this equipment. Alterations to this product, misuse of this product, or
failure to follow instructions may result in serious injury or death.
IMPORTANT
Questions regarding the use, care, or suitability of this equipment for your
application?
Contact Safewaze
This product meets or exceeds the following OSHA Regulations and ANSI
standards for fall protection.
| ANSI | OSHA |
|---|---|
| A14.3 | 1926.502 |
| Z359.1-2007 | 1910.140 |
| A10.32-2004 | 1910.66 |
INTRODUCTION
Thank you for purchasing the Safewaze 020-12101 EVO Detachable Cable Sleeve. This manual must be read and understood in its entirety and used as part of an employee training program as required by OSHA or any applicable state agency. This manual and any other instructional material must be available to the user of the equipment. The user must understand how to safely and effectively use the Cable Sleeve and all fall protection equipment used in conjunction with the Cable Sleeve.
APPLICABLE SAFETY STANDARDS
When used according to instructions, the 020-12101 EVO Detachable Cable Sleeve meets all applicable ANSI Z359 standards and OSHA regulations for fall protection. Applicable standards and regulations depend on the type of work being done and may include state-specific regulations. Refer to local, state, and federal (OSHA) requirements for additional information concerning the governing of occupational safety regarding Personal Fall Arrest Systems (PFAS).
WORKER CLASSIFICATIONS
Understand the definitions of those who work in proximity of or may be exposed to fall hazards. 220-00028 Qualified Person: “Qualified person” means one who, by possession of a recognized degree, certificate, or professional standing, or who by extensive knowledge, training, and experience, has successfully demonstrated his ability to solve or resolve problems relating to the subject matter, the work, or the project. Competent Person: A “Competent person” means one who is capable of identifying existing and predictable hazards in the surroundings or working conditions that are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
Authorized Person: “Authorized person” means a person approved or
assigned by the employer to perform a specific type of duty or duties or to be
at a specific location or location at the job site.
It is the responsibility of a Qualified or Competent person to supervise the
job
site and ensure safety regulations are complied with.
APPLICATIONS
Personal Fall Arrest: The 020-12101 Cable Sleeve is designed as a connection
point to support a maximum of 1 Personal Fall Arrest System (PFAS) when
utilized for fall protection applications. All above-referenced applications
have a worker weight capacity range of ANSI 130-310 lbs (including all
clothing, tools, and equipment), OSHA 420 lbs
COMPONENTS
- Cable Sleeve
- Energy Absorber
- Steel Captive Eye Carabiner
TECHNICAL DATA
020-12101 SKV EVO
Detachable Cable Sleeve:
| Part Number| Activation Force| Max Deployment
Length
| Minimum
Breaking Strength
---|---|---|---|---
020-12101| 450 lbf (2.0 kN)| 36 in. (914.4 mm)| 3,600 lbs (16kN)
Capacity
Each user must have a combined weight (clothing, tools, etc.) of 88 lb. to
310 lb. (40 kg to 140 kg). The Safewaze Fixed Ladder System may have up to 4
simultaneous users, but each 020-12101 EVO Detachable Cable Sleeve may have
only one user attached. For additional users, additional Cable Sleeves must be
used.
INSTALLATION AND USE
WARNING
Before the attachment of the 020- 2101 10 vertical ladder cable assembly,
the user must inspect all components of the entire ladder system. The user
must ensure that the ladder is undamaged and safe for climbing operations,
and confirm that the vertical cable is undamaged and free from excessive
corrosion. and inspect all other components of his/her Fall Arrest System
(PFAS).
- Under the guidance of a Competent Person, ensure that the 020-12101 is properly connected directly to the Sternal D-ring of the Full Body Harness via the captive eye carabiner (See Figure 2). Never attach the captive eye carabiner to another carabiner for connection to the sternal D-ring (See Figure 3). Before attaching the cable sleeve to the vertical cable, ensure that the cable is 3 in diameter.
- To attach the 020-12101 to the vertical cable constituent, rotate the locking lever up so that the lever clears the cable slot (See Figure 4). Rotate the locking cam lever upwards at the same time to clear the locking cam from the cable slot (See Figure 5).
- With the locking lever and locking cam clear of the cable slot, place the 020-12101 onto the vertical cable so that the cable is seated in the cable slot (See Figure 6)
- Release the locking lever and locking cam lever to complete the attachment to the vertical cable (See Figure 7)
- Once the 020-12101 is securely attached to both the user and the vertical cable constituent, climbing operations can begin.
- The 020-12101 is designed to work with the SafeWaze Vertical Ladder System. During climbing, if the integral energy-absorbing lanyard is oriented at a downward angle about the Cable Sleeve, the Cable Sleeve will remain stationary in place (See Figure 8).
- With the integral lanyard in an upward orientation relative to the Cable Sleeve the 020-12101 will trail along the cable as the user ascends the ladder (See Figure 9).
- Before beginning any climbing operations, ensure that the 010-12101 is installed correctly onto the vertical cable constituent. The cable sleeve has an arrow etched into the outer housing for the user’s reference to ensure correct installation. Do not use or begin climbing if the 020-12101 is installed improperly (upside down) on the vertical cable (See Figure 10).
- When ascending with the cable sleeve, the user must always maintain 3 points of contact with the fixed ladder assembly. The user should also climb in as straight of an orientation as possible (See Figure 11). The user should avoid leaning outward from the fixed ladder assembly when climbing, as this can place undue tension on the vertical cable and inhibit the proper operation of the cable sleeve (See Figure 12).
- If the user finds it necessary to maintain a stationary position on the fixed ladder, a positioning-type lanyard can be utilized if necessary (See Figure 13). The user should never disengage or remove the cable sleeve during climbing for any reason. If the user stops climbing, he/she should never attempt to use the vertical cable and cable sleeve as a positioning device (See Figure 13).
- the vertical ladder is of sufficient height to require cable guides, the user must know how to properly pass the guides during climbing operations. When the user reaches a point where the cable sleeve is just below the cable guide (See Figure 15), he/she must pull the cable free from the cable guide (See Figure 16). Once the cable is free of the guide, the user can slide the cable sleeve to a point above the cable guide (See Figure 16). Once the cable sleeve has cleared the cable guide, simply push the cable back into the guide and continue climbing operations (See Figure 17).
NOTE
USER MUST NEVER REMOVE THE CABLE SLEEVE FROM THE CABLE ASSEMBLY, OR THE
STERNAL D-RING OF THE FULL BODY HARNESS, AT ANY POINT WHILE CLIMBING THE FIXED
LADDER SYSTEM!
INSPECTION
- The 020-12101 shall be inspected by the user before each use and at least annually by a Competent Person. Annual Inspections must be documented. The severity of conditions during use may necessitate an increased frequency of documented inspections. Any Cable Sleeve that fails inspection MUST be removed from service.
- Before each use, inspect the 020-12101 for deficiencies or damage, including, but not limited to, sharp edges, rough edges, deformations, corrosion, pits, burrs, chemical exposure, extreme heat exposure, or missing or illegible labels. If any deficiencies or defects are found, the 020-12101 must IMMEDIATELY be removed from service.
- The 020-12101 must be inspected at least annually by a Competent Person other than the user. Competent person inspections must be recorded in the inspection log included in this manual and on the inspection grid label on the lanyard.
MAINTENANCE & STORAGE
The 020-12101 can be cleaned with water and mild soap if necessary. The user should remove all dirt, possible corrosives, and contaminants from the 020-12101 before, and after each use. Never use any type of corrosive substance to clean the 020-12101. Excess water should be blown out with compressed air. Hardware can be wiped off with a clean, dry cloth. When not in use, store the 020-12101 in a cool dry area where it will not be exposed to extreme light, extreme heat, excessive moisture, or possibly corrosive chemicals or materials
WARRANTY
Safewaze warrants its products are free from defects in materials and
construction under normal use and service. Liability is not accepted for
abuse, modification, improper use, destructive activity and contaminated
exposure.
WARNING
- Users should consult with their doctor to verify their ability to safely absorb the forces of a fall arrest event.
- Fitness level, age, and other health conditions can greatly affect an individual’s ability to withstand fall arrest forces. Women who are pregnant, and individuals considered minors must not use any Safewaze equipment.
- Cable Sleeves that are exposed to fall arrest forces MUST be IMMEDIATELY removed from service and destroyed.
- Never alter any part of the 020-12101 or add/remove components. Safewaze shall not be held responsible for injury or death due to tampering.
- Failure to follow these instructions and warnings could result in serious injury or death in the event of a fall.
- A preplanned rescue procedure in the event of a fall is required. The rescue plan must be specific to the project.
- The rescue plan must allow for employees to rescue themselves, or to be promptly rescued by alternative means.
- Harnesses or connectors selected for use with any Safewaze Cable Sleeve must be compatible in size and configuration.
- Users must ensure compatibility of snap hooks, carabiners and other connectors.
- Any connection that could allow disengagement must be eliminated. Snap hooks and carabiners must be self-locking and self-closing and must never be hooked to each other.
- A Competent Person must analyze the workplace and anticipate where workers will be conducting their duties, the route they will take to reach their work and the existing and potential fall hazards they may be exposed to.
- The Competent Persons must choose the fall protection equipment to be utilized.
- Do not misuse equipment.
- Equipment designated for fall protection must never be used to lift, hang, support or hoist tools or equipment unless specifically certified for such use.
LABELING
INSPECTION LOG
Date| Inspection Items Noted| Corrective Action|
Initials
---|---|---|---
| | |
| | |
| | |
225 Wilshire Ave SW, Concord NC, 28025
Phone: 800-230-0319 I Fax:
704-262-9051
Email: info@safewaze.com
Web: safewaze.com