SEALEY MS016.V2 Fork Seal Driver User Manual
- June 15, 2024
- SEALEY
Table of Contents
fork seal driver
MODEL NO: Ms016.v2
MS016.V2 Fork Seal Driver
Thank you for purchasing a sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction manual
safety
do NoT use the driver for a purpose it is not designed to perform.
do NoT use the driver if it is damaged, it could scratch the stanchion.
do NoT make any modifications to the driver.
m aintain the driver in a good clean condition for the best and safest
performance.
When not in use, store in a dry location.
INTRODUCTION
Designed for easy installation of fork seals. Limits potential damage caused by other installation methods to the forks.
specification
Model No.: ………………………………………………….. Ms016.v2
max. / min. Fork diameter ………………………….Ø35 – Ø47 mm
operation
always refer to the original manufacturer’s manual for assembly/disassembly of the motorcycle fork seals.
41. COLLET ORIENTATION (Refer to fig.3, fig.4).
411 Measure the stanchion diameter (2″A”) and the seal ring outer diameter.
Determine the required engagement diameter of the collet (@”B”) to the seal
ring and hence its orientation in order to obtain full seal ring insertion
(fig.3 and fig.4).
It is recommended that the collet diameter (@”B”) is slightly less than the
maximum seal ring diameter in order to allow for full seal fing insertion
412, Lightly lubricate the stanchion, slip on the new seal ring and slide it
down to the slider housing
4.13. From section 4.1.1 and figs.3 and 4, decide on the correct collet set up
(e.g. collet orientation) and slide it onto the stanchion
42. SLIDE HAMMER
421, Infig.3and fig.4 the pins in the slide hammer will be engaged with
opposing holes of the other half of the hammer however it may be such that the
engagement between the pins and holes will be lost (fig.5). In these
circumstances it will be necessary to align the two halves of the slide hammer
by eye in order to obtain even pressure and thus correctly aligned seal ring
insertion.
4.22. Holding the slide hammer halves together press the seal into the slider
housing. Replace seal retaining ring if required and repeat all tasks with the
other fork.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into
approved containers and dispose of the product and fluids according to local
regulations.
Note: Itis our policy to continually improve products and as such we reserve
the right to alter data, specifications and component parts without prior
notice. If you require documentation for altemative versions, please email or
call our technical team on
technical@sealey.co.uk or 01284 757505.
Important : No Liability is accepted for incorrect use of this product.
Warranty : Guarantee is 12 months from purchase date, proof of which is
required for any claim
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500 01284 703534
sales@sealey.co.uk
www.sealey.co.uk
MS016.V2
Issue 1 29/10119
© Jack Sealey Limited
Original Language Version
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>