CADDX FOV150 Walnut HD Action Camera 4K 60fps User Guide

CADDX FOV150 Walnut HD Action Camera 4K 60fps

Product Information

Specifications:

• Status indicator: Detachable ND filter
• Microphone
• Power button
• Type-C Memory card slot
• M button
• USB Magnetic Connector Buzzer

Introduction of Buttons:
The product includes the following buttons:

• Status indicator: Used to indicate the current status of the camera.
• Detachable ND filter: This allows you to attach or detach a neutral density (ND) filter to adjust the light entering the camera.
• Microphone: Captures audio during recording.
• Power button: Used to power on/off the camera.
• Type-C Memory card slot: Insert a memory card for storage.
• M button: Used for various functions and settings.
• USB Magnetic Connector Buzzer: Connects the camera to a computer or other devices for data transfer and charging.

Wiring:
The product requires wiring for power supply and remote control.

Follow the instructions below:

1. Connect the yellow wire (KEY signal line) to the FC UART TX pin on the flight control board.
2. Connect the black wire (GND) to the ground pin on the flight control board.
3. Connect the red wire (Vbat+) to a power source with a voltage range of 5~25.2V.

Power Supply and Remote Control:
The camera can be powered by a built-in battery or an external power supply within the voltage range of 5~25.2V. The camera also supports remote control for power on/off and start/stop recording.

To configure the remote control function, follow these steps:

1. Refer to the wiring diagram provided in the manual.
2. Configure the PINIO function of the TX1 pin on the flight controller according to the example given.
3. Map the PINIO function to the AUX channel of the remote control in the Betaflight Configuration.
4. Set the trigger mode and range for the PINIO function.
5. Save the configuration.

USB Magnetic Connector:
The USB connector can be attached to the back cover of the camera body using the magnetic feature. Make sure there are no foreign objects on the magnet surface that may affect the contact.

Data Transmission:
You can transfer data from the camera using one of the following methods:

1. Directly insert the memory card into a card reader to read data.
2. Insert a Type-C cable into the USB port on the side of the camera to read data.
3. Insert a Type-C cable into the USB magnetic connector to read data.

APP Download:
To download and install the CaddxFPV app, follow these steps:

1. Scan the QR code or search for CaddxFPV in the APP Store.
2. Turn on your phone’s WIFI and power on the camera.
3. Press the camera power button and wait for the camera buzzer to sound.
4. Long press the M button to turn on the camera WIFI.
5. Open the CaddxFPV app and click the Connect Now button.
6. Connect to the WIFI network named Caddx_***** with password 12345678.
7. After the connection is complete, you can access the camera through the app.
8. Click the gear icon in the lower right corner of the app to set camera parameters.

APP View Content:
After shooting, you can connect to the app and access the app album page to view your recorded content. The app also allows you to take photos and videos directly.

Mounting Case:
To prevent damage from falling, use the camera mounting adapter and choose a suitable base for installation when using the camera.

FAQ:

• Q: How can I power on/off the camera remotely?
  A: Follow the wiring and configuration instructions provided in the manual to enable remote control of the camera’s power function.

• Q: Can I transfer data from the camera using a card reader?
  A: Yes, you can directly insert the memory card into a card reader to read data.

• Q: How do I connect to the camera using the CaddxFPV app?
  A: Follow the step-by-step instructions provided in the manual to connect your phone to the camera’s WIFI network and access it through the CaddxFPV app.

• Q: Can I view and manage my recorded content through the app?
  A: Yes, the app allows you to view your recorded content, and you can also take photos and videos directly using the app.

Introduction of product

Introduction of Buttons

• When recording, slow flash corresponds to high battery power, and flash corresponds to low battery power
• If the camera is unresponsive press for 10 seconds to power off

Wiring

The KEY signal line can remotely control the camera through the flight control, please read the relevant precautions.

Power supply and remote control

The walnut camera uses two power supply modes: a built-in battery and a 5~25.2V external power supply. Supports remote control of the camera’s power on/off, start recording/stop recording. Take the commonly used flight controller Betaflight F405 as an example to illustrate how to configure the remote control to turn on/off the recording function. The wiring diagram is shown in the figure below, and the TX1 pin on the flight controller is used to control the recording on/off.

Enter the following blue fonts to configure the PINIO function of the TX1 pin.

• resource SERIAL_TX 1 NONE//Disable the serial port function of the TX1 pin
• resource PINIO 1 A09//Configure the TX1 pin (The example is A09 pin, different flight control pins are different, please fill in according to the actual) as PINIO function No. 1
• set pinio_box = 40,255,255,255 //Set the PINIO function range
• save //save configuration

Next, configure the PINIO function mapping between the remote controller and flight controller. In Betaflight Configuration, map the No. 1 PINIO function (ie USER1 in the figure below) to the AUX channel of the remote control.

The trigger mode is a low level trigger, the cursor from the yellow area to the white area and then to the yellow area is a trigger, the camera performs recording or stops recording.

USB Magnetic Connector

The USB connector can be connected by attaching it to the back cover of the walnut body. Pay attention to avoid sundries on the surface of the magnet that will affect the contact effect.

Data transmission

• Method 1: Directly insert the memory card into the card reader to read the data
• Method 2: Insert the Type-C cable into the USB port on the side of the walnut to read the camera data
• Method 3: Insert the Type-C cable into the USB magnetic connector to read the camera data

APP download

• Step 1: Scan the QR code below with your mobile phone or go to the APP Store to search for “CaddxFPV” to download and install the CaddxFPV app.
• Step 2: Turn on the phone WIFI. Short press the camera power button to turn on the camera and wait for the camera buzzer to sound, then long press the M button to turn on the camera WIFI.
• Step 3: Open the CaddxFPV app and click the “Connect Now” button. Connect to the WIFI whose name is “Caddx_*****”, and the WIFI password is “12345678”. After the connection is complete, click back and click to enter the camera.
• Step 4: Click the gear in the lower right corner of the app to set the camera parameters.

APP view content

After shooting, connect to the app, enter the app album page, and view the shooting content. You can also take photos and videos directly through the app.

Mounting case

The camera mounting adapter can prevent the camera from being damaged from falling, and you need to choose a suitable base for installation when using it.

Precautions

Regarding the use of accessories, please note:

1. The product or accessories contain small objects, be careful to prevent children from swallowing.
2. All accessories are not recommended to be used during high-intensity exercise, otherwise the camera or accessories may fall off.
3. Keep the magnetic surface clean to prevent poor connection.

Regarding the firmware upgrade, please note:

1. For the first time to use, please upgrade the firmware first
2. Before upgrading, please ensure that the camera is fully charged
3. Card swipe upgrade steps
4. First, delete the old firmware in the tf card (if any)
5. Import the latest firmware into the tf card
6. Insert the TF card into the camera TF card slot
7. Short press the power button to turn on
8. The blue light of the camera flashes quickly and enters the firmware flashing state
9. When the indicator light turns green, the firmware flashing is completed.

Indicator status

Camera status

|

Indicator status

---|---
The camera is powered on| Steady green light(the default is green light, the color of the light is different in different modes)
The camera is flashing the firmware| Blue light flashes quickly
camera is charging| Steady red light
4K recording mode| Steady green light
2.7k recording mode| Steady blue light
1440P recording mode| Steady Cyan light
1080P recording mode| Steady Cyan light
Charging while recording| Steady red light, Indicator light flashes slowly
Battery indicator| When the battery is above 70%, the flashing frequency of the light is once every 2s in the recording state
When the battery is 20~70%, the flashing frequency of the light is once every 1s in the recording state
When the battery is below 20%, the flashing frequency of the light is once every 0.5s in the recording state

The effective distance of the camera WIFI transmission (no interference and no obstruction) is 10 meters, and the effective transmission distance will vary due to different usage scenarios.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>