Caddx VISTA Kit DJI HD FPV System User Guide

VISTA KIT
Quick Start Guide
Nebula nano cam, Nebula micro cam, Nebula pro cam,
Nebula pro nano cam, Polar nano cam, Polar cam, Dji cam

CADDXFPV Support
Email: Support@caddxfpv.com
Disclaimer Congratulations on purchasing your new CADDXFPV product. The information in this document affects your safety and your legal rights and responsibilities. Read this entire document carefully to ensure proper configuration before use. Failure to read and follow instructions and warnings in this document may result in serious injury to yourself or others, damage to your CADDXFPV product, or damage to other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion of CADDXFPV. Visit www.caddxfpv.com for the latest information for this product.

By using this product, you hereby signify that you have read this disclaimer and warning carefully and that you understand and agree to abide by the terms and conditions herein. You agree that you are solely responsible for your own conduct while using this product, and for any consequences thereof. You agree to use this product only for purposes that are proper and in accordance with all applicable laws, rules, and regulations, and all terms, precautions, practices, policies, and guidelines CADDXFPV has made and may make available.
CADDXFPV accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of this product. The user shall observe safe and lawful practices including, but not limited to, those set forth in this document.
Notwithstanding the above, your statutory rights under applicable national legislation are not affected by this disclaimer.

Introduction

The CADDXFPV Vista is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 120fps image transmission, with a transmission range of up to 4 km and a minimum end-to-end latency within 28ms*. The vista can be mounted on a racing drone and used with DJI FPV Goggles or a remote controller to transmit video, control signals, and flight controller information wirelessly.

1. IPEX Antenna Ports
2. 3-in-1 Port
3. USB-C Port
4. Linking Status Indicator
5. Link Button
6. Camera

*The end-to-end latency is the total time from camera input to screen display. The device is able to reach its minimum latency and maximum transmission distance (FCC) in a wide-open area with no electromagnetic interference.

Connection

Refer to the illustration below to mount and connect the vista to a racing drone.

3-in-1 Cable (Power, DJI HDL, UART)

RED: Power 7.4-26.4V
BLACK: Power GND
YELLOW: UART RX(Connects to Flight Controller OSD TX,0-3.3V)
WHITE: UART TX(Connects to Flight Controller OSD RX, O-3.3V)
BLACK: Signal GND YELLOW: DJI HDL(Connects to Flight Controller S.Bus, O-3.3V)

• Electric soldering iron and soldering tin are required for connection. Make sure that there are no short circuits or open circuits when soldering the cable
• There are up to eight channels for the Vista depending on the region (FCC: eight, CE/SRRC: four, MIC: three). Each channel has a bandwidth of 20 MHz. The public channel is 8, which is the default channel when the equipment is powered on. The channel can be changed manually to avoid interference from other devices.
• **** The Vista may become hot during or after the operation. DO NOT touch the Vista before it cools down.
• DO NOT use the Vista for an extended period when the temperature is high or there is poor ventilation. Otherwise, the Vista may overheat and enter low-power mode which will affect its performance. If the Vista enters low-power mode, restart it or wait for it to cool down and it will automatically return to normal.
• Keep the Vista away from metal objects or carbon fiber frames.Make sure to choose a position where the transmission will not be blocked during flight.

Activation

When powered on, connected the vista to your computer and run DJI ASSIST ANTTm2 for activation.During the activation and upgrade process,there is a lot of heat.Please avoid direct contact to prevent burns. Overheating may lead to upgrading failure and unable to boot normally.You need to aware of the ambient temperature and use a fan to assist cooling. The warranty service does not support the crash caused by firmware refresh.
Download DJI Assistant 2 at https://www.dji.com/fpv/downloads

Linking

The vista support there linking methods: A. B, and A+B (Must link A before B).

1. Power on the vista and the DJI FPV Goggles.

2. Press the link button on the vista and the goggles.*

3. The linking status indicator of the vista turns solid green. The goggles stop beeping when successfully linked and the video display is normal.

4. Power on the vista and the DJI FPV Remote Controller.

5. Press the link button on the vista, and then press the record button, C button, and right dial on the remote controller simultaneously.*

6. Both the linking status indicators turn solid green when successfully linked.

• When ready to link, the devices will give the following indication:
  Vista: the linking status indicator turns solid red.
  Goggles: the goggles beep continually. Remote controller: the remote controller beeps continually and the status indicator blinks blue.

OSD display settings

1. After connecting the UART cable to the flight controller. take the Betaflight flight controller software setting as an example. Open the corresponding UART port and click save.
2. Select telemetered and OSD.click save.
3. Select the display content you need in the OSD page (some OSD are not supported, please wait for subsequent updates)
4. Select Settings-Display-Custom OSD ON in DJI FPV Goggle

Operating channel

Central
freillefICy(MHZ)| Channell| Channel2| Channel3| Channel4| Channels| Channel&| Channel?| Channel8
---|---|---|---|---|---|---|---|---
FCC| 5660| 5695| 5735| 5770| 5805| 5878| 5914| 5839
CE/SRRC| 5735| 5770| 5805| –| –| –| –| 5839
MIC| 5660| 5700| –| –| –| –| –| 5745

Make sure you fully understand and abide by local laws and regulations before using this product.An amateur radio license may be needed in FCC regions when using channels 1,2,6,or 7, as they are amateur frequency bands.Users who use the amateur frequency bands with a modified or cracked version or without a license may be punished for breaking local laws or regulations.

Specifications

Weight
Dimensions
Operating Frequency
Transmitter Power (EIRP)
Min. Latency (end-to-end)
Max. Transmission Distance
I/O Interface
Supported Flight
Control System
Operating
Temperature
Range Input Power
Camera parameters| Vista(excluding camera): 18.5g
Antenna: 2.5g/1.5g
Vista: 30 x 29 x 13.5 mm
Coaxial Cable: 120 mm/80mm 5.725-5.850 GHz
FCC/SRRC: <30 dBm; CE: <14 dBm
Low Latency Mode (720p 120fps): <28 ms;
High Quality Mode (720p 60fps): <40 ms
FCC/SRRC: 4 km; CE: 0.7 km;
USB-C,IPEX,3-in-1 port
Beta Flight
0° to 40° C (32° to 104° F)
7.4-26.4 V
---|---

Model
Weight
Dimensions
Image ratio
Min. Latency| Polar
9g
24 X19 x 19mm
16 : 9
720p 60fps < 32ms
---|---
Sensor| 1/1.8″ CMOS
Aperture: F/1.6
Shutter: Rolling shutter
Iso: 100-25600
FOV| 162°(D);138°(H);75°M

Model: Polar nano
Weight: 2.7g
Dimensions: 15.8x 14X 14mm
Image ratio: 16 : 9
Min.Latency: 720p 60fps < 32ms
Sensor: 1/1.8″ CMOS
Aperture: F/1.8
Shutter: Rolling shutter
Iso: 100-25600
FOV: 162°(D);138°(H);75°(V)
Model: Nebula pro
Weight: 6 g
Dimensions: 20 x 19 x 19mm
Image ratio: 16:9/4:3
Min.Latency: 720p 120fps < 28ms 720p 60fps < 32ms
Sensor: 1/3.2″ CMOS
Shutter: Rolling shutter
Iso: 100-25600
FOV: 150° (D);122° (H) ;93° (V)
Model: DJI cam
Weight: 8.2 g
Dimensions: 27.4 x 21.1 x 20.1mm
Image ratio: 16:9/4 :3
Min.Latency: 720p 120fps < 28ms 720p 60fps < 32ms
Sensor: 1/3.2″ CMOS
Shutter: Rolling shutter
Iso: 100-25600
FOV: 150° (D);122° (H) ;93° (V)
Model: Nebula nano
Weight: 3.5 g
Dimensions: 21 x 14 x 14mm
Image ratio: 16: 9
Min.Latency: 720p 60fps < 32ms
Sensor 1/3.2″ CMOS
Shutter: Rolling shutter Iso: 100-25600
FOV: 138° (D);122° (H) ;75° (V)
Model: Nebula micro
Weight: 5.8 g
Dimensions: 20 X19 X 19mm
Image ratio: 16: 9
Min.Latency: 720p 60fps < 32ms
Sensor: 1/3.2″ CMOS
Shutter: Rolling shutter
Iso: 100-25600
FOV: 138° (D);122° (H) ;75° (V)
Model: Nebula pro nano
Weight: 3.5g
Dimensions: 16.5x 16x 14mm
Image ratio: 16:9/4:3
Min.Latency : 720p 120fps < 28ms 720p 60fps < 32ms
Sensor 1/3.2″ CMOS
Shutter: Rolling shutter
Iso: 100-25600
FOV: 150° (D);122° (H) ;93° (V)

Menu board

The polar camera supports menu board adjustment, this function requires self- welding, welding and disassembly are risky, please be aware.

1. Remove the screws of the back cover. Remove the nylon spacers.

2. Solder the menu wire and the gnd wire. Install the back cover. Connect the OSD menu board.

3. Left/Right button Control the increase or decrease of saturation.

4. Up/Down button Control the increase or decrease of brightness.

5. Middle button Short press to save, long press for 3 seconds to restore factory settings.

• Menu board needs to be purchased separately
  This content is subject to change.
  Download the latest version from https://www.caddxfpv.com/pega/download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>