HIKVISION DS-D5022FC-C 21.5-inch FHD Monitor User Manual
- June 4, 2024
- Hikvision
Table of Contents
HIKVISION DS-D5022FC-C 21.5-inch FHD Monitor
Applicable Models
This manual is applicable to monitor.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
| Symbol | Description |
|---|---|
| Provides additional information to emphasize or supplement important points |
of the main text.
| Indicates a potentially hazardous situation, which if not avoided, could
result in equipment damage, data loss, performance degradation, or unexpected
results.
| Indicates a hazard with a high level of risk, which if not avoided, will
result in death or serious injury.
Introduction
Key Features
- 8-bit/10-bit dual channel LVDS (1920×1080) HD display.
- 3D digital comb filter and 3D noise reduction technology.
- Hi-Fi color OSD and user-friendly menu for operation.
- Mstar ACE-5 auto color and image enhancement engine, improving the image contrast, details, edges, etc.
- Programmable 12-bit RGB gamma correction.
- Complete factory setting mode.
- 1 × HDMI 1.4b input interface, and HDCP 1.4 available.
- Software spread spectrum technology reduces EMI radiation.
- HD JPEG decoding.
- Professional and standard CVBS input interface with one channel input available.
- Multimedia playing of text, image, audio, video, etc.
NOTE: The specific features may vary with models. Refer to Rear Panel Interface for details.
Packing List
| Name | Quantity | Name | Quantity |
|---|---|---|---|
| Monitor | 1 | Power cable | 1 |
| Remote control (Optional) | 1 | Base set | 1 |
| Battery (Optional) | 2 | User manual | 1 |
| HDMI cable (Optional) | 1 | Quick start guide | 1 |
Power On
Connect the device to an earthed mains socket-outlet, and press the power button.
- Power supply: 220 VAC~, 50/60 Hz.
- Power off the device and disconnect the plug if it is not in use for a long time.
- The device cannot be connected to DC power supply.
Rear Panel Interface
The panel appearances and interfaces vary with different models. The devices can be classified as follows.
Interface Description
| Interface | Description | Interface | Description |
|---|---|---|---|
| VGA | VGA analog signal input interface | POWER | Power supply |
| Interface | Description | Interface | Description |
| --- | --- | --- | --- |
| HDMI | HDMI digital signal input interface | USB | USB 2.0 input interface |
| AUDIO | Audio input interface | CVBS | CVBS signal input interface |
NOTE: USB and CVBS input interfaces are available to type A and D, and audio input interface to type A, C, and D.
Panel Buttons
The buttons at the bottom-right corner of the front panel are shown as follows.
Button Description
| Button | Description |
|---|---|
| Power On/Off | |
| Second-level menu page: Exit menu. |
File selection for USB playing: play
Other pages: Display main menu page.
| Display the current input source.
All the menu pages: OK
| First-level page: previous/next
Second-level page: add/reduce
USB playing page: volume up/down
| Display all the input sources.
All the menu pages: Switch to next one.
Remote Control
Remote Control Description
| Appearance | Button | Description |
|---|
|
| Power on/off
| Mute/Unmute
【FREEZE】| Freeze the current display.
【MENU】| Go to menu settings.
【SOURCE】| Check or select a signal source.
| Up/Down/Left/Right
【OK】| OK
| Play/Pause
| Stop
| Previous/Next
| Repeat
| Return
NOTE: The remote control is not available to all kinds of devices. Whether your device is equipped with a remote control depends on the actual situation.
Basic Operation
The interfaces vary with different models. The figures followed are for illustration purpose only.
Switch the Signal Source
Connect the device to power source and signal source, and power the device on.
STEP 1: Press to enter the signal source page.
STEP 2: Press to switch input sources, and press to confirm.
Menu Operation
Basic Operation
| Operation | Description |
|---|---|
| Enter main menu page | Press |
| Check first-level menu | On the main menu page, press to switch. |
| Check parameters | On the first-level menu page, press to enter and check |
different parameters.
Configure parameters| Press< OR >to adjust the value of the selected
parameter, and press to conf.rm.
Press to switch to other parameters.
Return to the upper menu| Press on any pages.
Image Settings
You can switch image modes and adjust image parameters including contrast,
brightness, color, sharpness, and hue. The adjustable parameters will change
when you switch from one image mode to another.
Image Parameters
| Parameter | Description |
|---|---|
| Image Mode | Standard : Suitable for a normal environment. It is set as |
the default picture mode.
Gentle : Suitable for a dark room.
Dynamic : Suitable for a bright room.
User : Set the brightness, contrast, color, sharpness or hue to adjust
display effect.
Brightness| Ranges from 0 to 100. The higher the value is, the brighter the
display will be.
Contrast| Ranges from 0 to 100. The higher the value is, the clearer the image
will be
Color| Ranges from 0 to 100. The higher the value is, the more colorful the
image will be.
Sharpness| Ranges from 0 to 100. Rise the value up to make the image more
vivid.
Hue| Ranges from 0 to 100. It determines the contrast degree between the
bright and dark.
NOTE
- If the user mode selected, the adjustable parameters are determined by the input signal.
- For VGA input, brightness and contrast are adjustable.
- For HDMI input, brightness, contrast, color, and sharpness are adjustable.
- For CVBS input, brightness, contrast, color, sharpness, and hue are adjustable.
- For USB (not supported by Type B and C), brightness, contrast, color, and sharpness are adjustable.
- Parameters in white bar are adjustable. If the parameter bar is gray, it indicates that the parameter is not adjustable under the current mode or input source.
BACKLIGHT
The backlight value ranges from 0 to 100.
VGA parameter
When you select VGA as the input source, you can adjust VGA parameters to
make the picture show in the correct position.
| Parameter | Description |
|---|---|
| Adjust | Adjust. Press < or to enable or disable. |
| Row | Ranges from 0 to 100. |
| Column | Ranges from 0 to 100. |
| Clock | Ranges from 0 to 100. |
| Phase | Ranges from 0 to 100. |
| Auto Lock | Off/On |
NOTE
-
Adjusting the value of H-Position and V-Position will change the image position in a large extent, while Phase and Clock in a slight extent.
-
Change the value of Clock will stretch or narrow the image.
-
If Auto Lock is enabled, the related parameters will self-adjust under the following 3 circumstances: The device is restarted, a VGA input source is accessed, and the input
source is switched to VGA. -
VGA parameters cannot be changed when Auto Lock is disabled.
Display Settings
Overscan
If Overscan is enabled, you can set the value of the top/bottom/left/right
edge. The value indicates the covered units of different directions.
Overscan Parameters
| Parameter | Description |
|---|---|
| Overscan | Off/On |
| Left Edge | Ranges from 0 to 100. |
| Right Edge | Ranges from 0 to 100. |
| Top Edge | Ranges from 0 to 100. |
| Bottom Edge | Ranges from 0 to 100. |
ASPECT
Scale up/down the image. Three kinds of aspects are available: 16:9, 4:3, and
point to point.
NOTE: Point to Point mode is only available when a VGA or HDMI signal is accessed.
KEYPAD
When no need to use keypad or the installation environment may extrude the
keypad, you can set the Keypad as Off to lock it.
EYE PROTECTION
Disabled by default. If enabled, the screen switches to eye protection mode.
NOTE: Eye Protection is only available to type D.
System Maintenance and Info
Maintenance
Contact our technical support personnel for upgrade program and USB driver.
-
Upgrade: Insert the USB driver to the USB interface, and set Upgrade (USB) as On.
Follow the instructions on the screen to upgrade. -
Restore Defaults: Restore all the settings to the default value.
SYSTEM INFO
Check the version, working time, ID, and serial number of the device.
System Settings
OSD SETTING
OSD Parameters
| Parameter | Description |
|---|---|
| Language | English/中文 |
| OSD Duration | Always On/5 s/15 s/30 s. The displaying time for OSD menu when |
no operation is done.
OSD Blending| Low/Medium/High/Off
AUDIO MODE
You can set the volume as desired or mute/unmute the playing.
Audio Mode Parameters
| Parameter | Description |
|---|---|
| Mute | Off/On. Off by default. |
| Volume | Ranges from 0 to 100. |
| Balance | Ranges from 0 to 100. |
NOTE : Audio mode is only available to type A and D.
OTHER SETTING
Screen Saver Parameters
| Parameter | Description |
|---|---|
| No Signal | Black/Blue. The screen color to be displayed when no signal is |
detected.
Image Freeze| Yes/No.
COLOR SETTINGS
| Parameter | Description |
|---|---|
| Color Space | 0-255/16-235 |
NOTE: Image Freeze changes to No when you switch the signal source or restart the device.
USB Menu
NOTE: USB menu is only available to type A and D.
- Press and insert your removable storage device into the USB interface of the device.
- Select USB as the input signal source, and then the USB menu displays.
- Press < or > to select your desired file type for playing.
- Press to confirm.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>