elk HOME 89704-4 Transitional Neville Charcoal Black Flush Mount Lighting Fixture Installation Guide

: June 15, 2024
: elk HOME

Table of Contents

Assembly Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

elk HOME 89704-4 Transitional Neville Charcoal Black Flush Mount Lighting Fixture Installation Guide

WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.

WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.

Before assembly, remove all parts and part packages from box. If anything is missing, please contact the retailer from which the product was purchased.

Assembly Instructions

Carefully pull house wires out of junction box so they are easily accessible during installation.
Position mounting bracket (A) so threaded ends of attached fixture mounting screws (E) are facing down towards floor.
Carefully pull house wires through center hole in mounting bracket (A). Align small holes in mounting bracket (A) with holes in junction box.
Thread each junction box screw (B) into appropriate hole in mounting bracket (A) and into hole in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.

CAUTION: Make sure house wires are pulled completely through hole in mounting bracket.
DO NOT pinch wires between mounting bracket and ceiling.

Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.
Carefully push fixture wires up through bottom of long threaded pipe (M). Pull fixture wires taut.
Thread bottom of long threaded pipe (M) into coupling in center of fixture body (O).
Push fixture wires through tube (N) and top trim (G). Slip tube (N) then top trim (G) over long threaded pipe (M).
Lower shade (K) down over long threaded pipe (M). Pass hole in bracket on shade (K) over top of long threaded pipe (M).
Pass fixture wires through hole in center of diffuser (H). Pass hole in center of diffuser (H) over end of long threaded pipe (M). Thread one small screw (L) into each hole along diffuser (H) and into holes in bracket on shade (K). Tighten small screws (L) to secure diffuser (H ) in place. DO NOT over tighten.
Pass fixture wires through hole in cap (P). Slip cap (P) over end of long threaded pipe (M) protruding from top of diffuser (H).
Hold threaded pipe (S) so coupling on end of threaded pipe is on the bottom. Pass fixture wires through threaded pipe (S). Screw bottom of threaded pipe (S) onto top of long threaded pipe (M).
Pass fixture wires through hole in short tube (R) and cap (P). Slip short tube (R) then cap (P) down over threaded pipe (S).
Pass fixture wires through hole in canopy (D). Pass hole in canopy (D) over end of threaded pipe (S).
Slip fixture wires through bushing (T). Insert bushing (T) into top of threaded pipe (S) protruding from inside canopy (D).
Slip fixture wires through lock washer (V) and hex nut (W). Slip lock washer (V) over end of threaded pipe (S). Thread hex nut (W) onto threaded pipe (S). Tighten hex nut (W) to secure canopy (D) in place.
Strip 3/4” of insulation from ends of fixture wires.
Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire (copper) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.
Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
Carefully push all wires and wire nuts into junction box.
Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
---|---
Black Wire or,| White Wire or,
Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
No printed words on wire insulation or,| Printed words on wire insulation or,
Insulated Wire (other than green) with Copper Conductor.| Insulated Wire (other than green) with Silver Conductor.
*When parallel wire (SPT 1 & SPT 2) is used: The lead wire is round in shape or smooth. The neutral wire is square in shape or ridged.
Carefully raise fixture up to ceiling. Place canopy (D) of fixture over mounting bracket (A). Pass holes in canopy (D) over ends of fixture mounting screws (E).
Screw one threaded cap (F) onto end of each fixture mounting screw (E). Tighten threaded caps (F) to secure fixture to ceiling. DO NOT over tighten.