elk HOME 89800-1 Hoyle Light 7 inch Brushed Gold Vanity Instruction Manual

elk HOME 89800-1 Hoyle Light 7 inch Brushed Gold Vanity

Product Information

This product is a fixture that is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. It is recommended to have the fixture installed by a certified electrician if you are not familiar with code requirements. The fixture comes with a mounting bracket, junction box screws, ground screw, wire nuts, and a backplate.

Specifications

• Item #: 89780/1, 89790/1, 89800/1
• Junction Box: GND GND

Product Usage Instructions

Installation

1. Disconnect power at the main fuse box before installation.
2. Position the mounting bracket (A) so that the threaded ends of the attached fixture mounting screws (E) are facing out.
3. Carefully pull the house wires through the center hole in the mounting bracket (A) and align the holes in the mounting bracket with the holes in the junction box. Make sure the fixture mounting screws (E) are level.
4. Thread each junction box screw (B) into the appropriate holes in the mounting bracket (A) and into the holes in the junction box.
   Tighten the junction box screws (B) to secure the mounting bracket (A) to the junction box. Make sure the house wires are pulled completely through the hole in the mounting bracket and avoid pinching the wires between the mounting bracket and wall.

Wire Connections

5. Strip 3/4 of insulation from the ends of the fixture wires.
6. Slightly loosen the ground screw on the mounting bracket (A) and wrap the house ground wire (copper) around the ground screw. Leave enough ground wire to attach to the fixture ground wire. Twist the end of the fixture ground wire and the end of the house ground wire (copper) together. Use a wire nut (C) to secure the ends of the wires.
7. Twist the end of the house lead wire (black) and the end of the fixture lead wire together. Use a wire nut (C) to secure the ends of the wires. Repeat this step for the house neutral wire (white) and fixture neutral wire.
8. Wrap electrical tape around the wire nuts (C) and wires to ensure they are securely fastened.
9. Carefully push all wires and wire nuts into the junction box.

Mounting

9. Place the backplate (D) over the mounting bracket (A) and pass the holes in the backplate over the ends of the fixture mounting screws (E). Avoid pinching wires between the backplate and wall.

FAQ

Q: What should I do if any parts are missing?

If anything is missing from the product packaging, please contact the retailer from which you purchased the product for assistance.

Q: How can I get further support or ask questions?

If you have any questions or need further assistance, you can call our support line at 800-613-3261 from Monday to Friday, 8:00 AM to 6:00 PM ET.

ANY QUESTIONS CALL: 800-613-3261

M-F 8:00AM-6:00PM ET

• ITEM#: 89780/1
• ITEM#: 89790/1
• ITEM#: 89800/1

WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.

WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
Before assembly, remove all parts and part packages from box. If anything is missing, please contact the retailer from which the product was purchased.

INSTALLATION

1. Position mounting bracket (A) so threaded ends of attached fixture mounting screws (E) are facing out.

2. Carefully pull house wires through center hole in mounting bracket (A). Align holes in mounting bracket (A) with holes in junction box. Make sure fixture mounting screws (E) are level.

3. Thread each junction box screw (B) into appropriate holes in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box. CAUTION: Make sure house wires are pulled completely through hole in mounting bracket. DO NOT pinch wires between mounting bracket and wall.

4. Strip 3/4” of insulation from ends of fixture wires.

5. Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire (copper) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.

Connect Supply (House) Ground Copper Wire to:

  * Bare Copper Wire or,
  * Bare Silver Wire or,
  * Green Insulated Wire.

6. Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.

7. Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.

8. Carefully push all wires and wire nuts into junction box.

9. Place backplate (D) over mounting bracket (A). Pass holes in backplate (D) over ends of fixture mounting screws (E). CAUTION: Do not pinch wires between backplate and wall.

10. Screw one threaded cap (F) onto end of each fixture mounting screw (E). Tighten threaded caps (F) to secure fixture (D) to wall. DO NOT over tighten.

11. Place harp (L) down on top of candle cover.

12. Screw recommended bulb (E12 candelabra bulb type, not included) into socket. Verify correct bulb wattage marked on socket of fixture. WARNING: DO NOT exceed maximum bulb wattage.

13. Lower shade (K) down over harp (L). Set shade (K) on top of harp (L).

elkhome.com

References

• elkhome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>