elk HOME 82288-10 Transitional Harwell Ten Light Chandelier Instruction Manual

: June 15, 2024
: elk HOME

Table of Contents

elk HOME 82288-10 Transitional Harwell Ten Light Chandelier
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

elk HOME 82288-10 Transitional Harwell Ten Light Chandelier

WARNING
DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.

WARNING
This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Before assembly, remove all parts and part packages from the box. If anything is missing, please contact the retailer from which the product was purchased.

Installation

Carefully pull house wires down out of a junction box so house wires are easily accessed to connect fixture wires.
If screw collar loop (W) is already attached to mounting bracket (A), proceed to Step 3. To assemble screw collar loop (W) to mounting bracket (A): Hold mounting bracket (A) so head of ground screw is pointing down towards floor. Hold threaded pipe so two hexnuts already attached to threaded pipe (E) are pointing down towards floor.
From side of mounting bracket with ground screw head, screw short end of threaded pipe (E) into hole in center of mounting
bracket (A) until hexnut on threaded pipe (E) touches mounting bracket. Thread hexnut (V) onto end of threaded pipe (E).
Tighten hexnut (V) to secure threaded pipe (E) to mounting bracket (A). Thread screw collar loop (W) onto
end of threaded pipe pointing down towards floor. Tighten screw collar loop up against hexnut on threaded pipe (E).
Place mounting bracket (A) up against junction box. Screw collar loop (E) should be pointing down towards floor. Align each slot in mounting bracket (A) with each hole in junction box. Thread one junction box screw (B) into each slot in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between mounting bracket and ceiling.
IMPORTANT: DO NOT tighten thumbscrews (K) and threaded caps (L) until all arms (M) are attached.
Insert bottom of one arm (M) in between tabs on fixture body (O). Align hole in arm with holes in tabs.
Pass thumbscrew (K) through hole in tab, through hole in arm and through hole in second tab. Screw threaded cap (L) onto end of thumbscrew (K).
Insert top of arm in between tabs on hub (N). Align hole in arm with holes in tabs.
Pass thumbscrew (K) through hole in tab, throughhole in arm and through hole in second tab. Screw threaded cap (L) onto end of thumbscrew (K).
Repeat steps 5-8 to attach remaining arms (M).
After all arms have been attached, completely tighten thumbscrews (K) and threaded caps (L).
Connect one locking link (G) to loop on top of hub (N).
Determine desired hanging height of fixture. Cut chain (H) to length to achieve desired height.
Slip chain link at end of chain (H) onto locking link (G) on loop.
Weave fixture wires through chain links, skipping every other chain link.
Slip threaded ring (F) down over end of chain (H).
Position canopy (D) so outside of canopy is pointing down towards fixture. Slip hole in canopy (D) over end of chain (H).
Strip 3/4” of insulation from ends of fixture wires.
Carefully push fixture wires up through hole in screw collar loop (W) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
To aid in connecting fixture wires to housewires, temporarily connect second locking link (G) to link at end of chain (H) and to screw collar loop (W).
Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of
fixture ground wire and end of house groundwire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) andend of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
Carefully push all wires and wire nuts into junction box.
Remove second locking link (G) from last link on chain (H) and screw collar loop (W).
Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (W). Position canopy (D) up against ceiling.
Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (W). Tighten threaded ring (F) to secure fixture to ceiling.
Attach second locking link (G) to link at end of chain (H). Attach locking link (G) at end of chain (H) to loop on screw collar loop (W).
Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.