RAIDER 030130 Charger Battery Cordless Drill Instruction Manual
- June 15, 2024
- Raider
Table of Contents
for 8 Ah battery
030130 Charger Battery Cordless Drill
Charger
www.raider.bg
| Art. No.| Item Description
---|---|---
| 30130| R20 Cordless Drill Li-ion 2 speed 13mm 44Nm Solo RDP-SCD20
| 30131| R20 Cordless Hammer Drill-Driver Li-ion 2 speed 13mm 50Nm Solo
RDPSCDI20
| 30132| R20 Cordless Hex Impact Driver Li-ion 1/4″ 180Nm Solo RDP-SHID20
| 30133| R20 Cordless Impact Wrench Li-ion 1/2″ 250Nm Solo RDP-SCIW20
| 30134| R20 Cordless Impact Wrench Li-ion 1/2″ 400Nm 5 speed Solo RDP-
SCIW20-5
| 30135| R20 Cordless Rotary Hammer Li-ion SDS-plus Solo RDP-SRH20
| 30136| R20 Cordless Angle Grinder Li-ion Ø125mm 10000min-1 Solo RDP-SAG20
| 30137| R20 Cordless Jig Saw Li-ion quick 80mm Solo RDP-SJS20
| 30138| R20 Cordless Reciprocating Saw Li-ion quick Solo RDP-SRS20
| 30139| R20 Cordless Circular Saw Li-ion Ø165x20mm 24T 4200min-1 laser Solo
RDP-SCS20
| 163143| Circular Saw Blade Tungsten Carbide Tipped Ø165x20mm24T
| 30140| R20 Cordless Random Orbit Sander Li-ion Ø125mm variable speed Solo
RDP-SRSA20
| 30141| R20 Cordless Multi-Tool Li-ion 3° variable speed quick Solo RDP-
SOMT20
| 30211| Cordless Drill Li-ion 2 speed 13mm 44Nm 20V 1.5Ah 1h RDP-SCD20 Set
| 30208| Cordless Hammer Drill-Driver Li-ion 2 speed 13mm 50Nm 20V 2x2Ah 1h in
Case RDP-SCDI20 Set
| 30209| Cordless Angle Grinder Li-ion Ø125mm 10000min-1 20V 2Ah 1h in Case
RDPSAG20 Set
| 30210| Cordless Jig Saw Li-ion quick 80mm 20V 2Ah 1h in Case RDP-SJS20 Set
| 32120| R20 System Starter Kit Li-ion 2Ah 1h for series RDP-R20 System
| 131110| R20 Battery Pack Li-ion 20V 1.5Ah for series RDP-R20 System
| 131152| R20 Battery Pack Li-ion 20V 2Ah for series RDP-R20 System
| 131153| R20 Battery Pack Li-ion 20V 4Ah for series RDP-R20 System
| 39713| R20 Charger for series RDP-R20 System
| 39704| R20 Rapid Charger for series RDP-R20 System
Description of elements
- Nameplate
- Cord
- Plug
- Guiderail
- Contacts
- LDC Charge indicator
- Ventilation holes
- Body
Refer to instruction manual booklet!
Dear Users,
Congratulations on buying a charger from the fastest growing brand for
electric, gasoline and pneumatic machines – RAIDER. With proper installation
and operation, RAIDER are reliable and reliable machines, and the work with
them will bring you real pleasure. For your convenience, there is an excellent
service network with 45 service stations all over the country.
Before using this charger, please read this “Instruction for Use” carefully.
For the sake of your safety and to ensure proper use, read these instructions
carefully, including the recommendations and warnings therein. To avoid
unnecessary errors and incidents, it is important that these instructions
remain available for future reference to anyone who will use the charger. If
you sell it to a new owner, the “Instruction for Use” must be handed over to
the new owner so that the new user can read the relevant safety precautions
and operating instructions.
“Euromaster Import Export” Ltd is an authorized representative of the
manufacturer and owner of the trademark RAIDER. The address of the company’s
management is in Sofia 1231, 244 Lomsko Shosse Blvd., tel. 02934 33 33, 934 10
10, www.raider.bg;
www.euromasterbg.com; e-mail:
info@euromasterbg.com.
Since 2006 the company has introduced the ISO 9001: 2008 quality management
system with scope of certification: Trade, import, export and servicing of
professional and hobby electric, pneumatic and mechanical tools and general
hardware. The certificate is issued by Moody International Certification Ltd,
England.
Charger
parameter| unit measure| value
Art. №| –| 39713
Voltage| V AC| 230
Frequency| Hz| 50
Rated output voltage| V DC| 20
Rated output current| А| 8
Protection class| –| II
NOTE: Store these instructions in a safe place. Only use the charger if you can fully evaluate all functions and carry them out without restrictions, or if you have received corresponding instructions.
- Always charge indoors. Because the charger and battery heat slightly during charging, charge the battery in a place not exposed to direct sunlight; where the humidity is low and the ventilation is good.
- This charger is not intended for use by children or persons with physical, sensory or mental limitations or a lack of experience or knowledge. This charger can be used by children aged 8 or older and by persons who have physical, sensory or mental limitations or a lack of experience or knowledge if a person responsible for their safety supervises them or has instructed them in the safe operation of the charger and they understand the associated dangers. Otherwise, there is a risk of operating errors and injuries.
- Supervise children during use, cleaning and maintenance. This will ensure that children do not play with the charger.
- Use R20 series lithium-ion batteries for charging. The battery voltage must match the battery charging voltage of the charger. Do not charge any non- rechargeable batteries. Otherwise there is a risk of fire and explosion.
- Do not expose the charger to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Keep the charger clean. Dirt poses a risk of electric shock.
- Always check the charger, cable and plug before use. Stop using the charger if you discover any damage. Do not open the charger yourself, and have it repaired only by a qualified specialist using only original replacement parts. Damaged chargers, cables and plugs increase the risk of electric shock.
- Make absolutely sure that the terminal area of the charger is free of any adhering foreign material or liquid. If there is any foreign material or liquid, remove before use.
- Do not operate the charger on an easily ignited surface (e.g. paper, textiles, etc.) or in a flammable environment. There is a risk of fire due to the charger heating up during operation.
- In case of damage and improper use of the battery, vapours may also be emitted.
Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system.
GENERAL OPERATIONAL INSTRUCTIONS
-
Always charge the battery at an ambient temperature of 5–45°C. A temperature of less than 5°C will result in over charging which is dangerous.
The battery cannot be charged at a temperature greater than 45°C.
The most suitable temperature for charging is that of 20–25°C. -
Do not use the charger continuously.
When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. -
Don’t abuse cord. Never carry charger by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil and sharp edges. -
When the charger is not in use or when being maintained and inspected, disconnect the power cord of the charger from the receptacle and remove the battery from the charger.
-
Do not cover the ventilation slots of the charger. Otherwise, the charger may overheat and no long function properly.
-
When not in use, the charger should be stored in dry, high or locked-up place – out of reach of children. Store the battery and charger in a place in which the temperature is less than 50°C.
-
To ensure the designed operational integrity of power tools and charger, do not remove installed covers or screws.
-
Always use the charger at the voltage specified on the nameplate.
-
Never disassemble the battery or charger.
-
Never short-circuit the battery. Short-circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery.
-
Do not dispose of the battery in fire. If the battery is burnt, it may explode.
-
Using an exhausted battery will damage the charger.
-
Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery.
-
Do not insert objects into the air ventilation slots of the charger. Inserting metal objects or flammable into the charger air ventilation slots will result in an electrical shock hazard or damage to the charger.
BEFORE USE
The workplace should be well cleaned, remove unnecessary items. Ensure that
lighting and ventilation is adequate.
CHARGING METHOD
NOTE: Before plugging into the receptacle, make sure the following
points.
The power source voltage is stated on the nameplate.
The cord is not damaged. WARNING: Do not charge at voltage higher than
indicated on the nameplate. If charged at voltage higher than indicated on the
nameplate, the charger will burn up.
-
Connect the battery charger’s power cord to the receptacle(power source). When connecting the plug of the charger to a receptacle, the charger will convert to pre-charge mode.
WARNING: Do not use the electrical cord if damaged. Have it repaired immediately. -
Insert and slide the battery onto the charger along the guide rail, the charger will convert to regular charging mode.
LCD Charge indicator indication
The indications of the LCD Charge indicator will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.
Table 1
The charger may become warm and buzz slightly during charging. This is normal and does not indicate a fault.
Temperatures at which the battery can berecharged – 5°C –45°C
NOTE: 1. If only cross mark on the LCD, unplug the charger from the
receptacle and reinstall the battery again. 2. If cross and thermometer marks
on the LCD, remove and cool down the battery before being recharged. 3.The
recharging time may vary according to the ambient temperature. 3. Disconnect
battery charger from the receptacle. CAUTION: Do not pull the plug out of the
receptacle by pulling on the cord. Make sure to grasp the plug when removing
from receptacleto avoid damaging cord. 4. Remove the battery from the battery
charger. Supporting the battery charger with hand, pull out the battery from
the battery charger.
NOTE:
- Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
- Charge the battery fully before using it for the first time.
- Push the battery into the battery holder until it engages with an audible click.
- Check that the battery is seated securely.
- Be sure to pull out the battery from the battery charger after use, and then keep it.
REGARDING ELECTRIC DISCHARGE IN CASE OF NEW BATTERIES, ETC
As the internal chemical substance of new batteries and batteries that have
not been used for an extended period is not activated, the electric discharge
might be low when using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will be restored by
recharging the batteries 2 – 3 times.
HOW TO MAKE THE BATTERIES PERFORM LONGER
Recharge the batteries before they become completely exhausted. When you feel
that the power of the tool becomes weaker, stop using the tool and recharge
its battery. If you continue to use the tool and exhaust the electric current,
the battery may be damaged and its life will become shorter.
Avoid recharging at hightemperatures. A rechargeable battery will be hot
immediately after use. If such a battery is recharged immediately after use,
its internal chemical substance will deteriorate, and the battery life will be
shortened. Leave the battery and recharge it after it has cooled for a while.
CAUTION: When the battery charger has been continuously used, the battery
charger will be heated, thus constituting the cause of the failures. Once the
charging has been completed, give 15 minutes rest until the next charging.
MAINTENANCE AND INSPECTION
CAUTION: Pull out battery before doing any inspection ormaintenance.
-
Check the Screws
Loose screws are dangerous. Regularly inspect them and make sure they are tight.
CAUTION: Using this battery charger with loosened screws is extremely dangerous. -
Check for Dust
Dust may be removed with a soft cloth or a cloth dampened with soapy water. Do not use bleach, chlorine, gasoline or thinner, for they may damage the plastics.
CAUTION: Repair, modification and inspection of the charger must only be
carried out by an authorized service center of Euromaster Import Export LTD
STORAGE
Storing in a place below 122°F (50°C) and out of the reach of children.
TROUBLE SHOOTING
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Euromaster Import-Export LDT Service Centers, always using Raider replacement parts for repairs.
| State of abnormality | Probablecause (malfunction) | Remedy |
|---|
The LCD Charge indicator are still off after connecting the charger to the
power source (receptacle).| The charger is not well connected to the suitable
power source (receptacle).| Make sure the power source voltage is same as that
stated on the charger nameplate, and correctly connected.
The charger or its cable is Damaged.| Replace with a new one.
The LCD Charge Indicator is damaged.| Ask your local authorized service center
for repair.
The battery cartridge not charging.| The battery cartridge is hot or ambient
temperature is very cold or hot.| Cool down the battery cartridge, and
recharge at room temperature.
The battery is not in position or damaged.| Re-insert battery fully in
position, if still not charging, replace the battery.
There is no cooling sounds heard during Charging| The cooling fan is damaged|
Ask your local authorized service center for repair.
ENVIRONMENTAL PROTECTION
In order to protect the environment, the power tool and packaging must be subjected to appropriate processing for the reuse of their contents raw materials. Do not dispose of power tools with household waste! According to the Directive of the European Union 2012/19/EC concerning end-of-life electrical and electronic equipment devices and the approval and as a national law power tools that cannot to be used more, they must be collected separately and subjected to an appropriate processing for the recovery of the raw materials contained in them.
WARRANTY CARD
Art.N………………………………………………………………………………………………………………..
SERIAL № ………………………………………………………………………………………………………
TERM ………………………………………………………………………………………………………………
(for details see the warranty conditions)
№, date of invoice / cash receipt
DETAILS OF BUYER
……………………………………………………………………………………..
NAME / COMPANY …………………………………………………………………………………………..
(be filled in by the employee)
(be filled in by the employee)
ADDRESSS………………………………………………………………………………………………………
SIGNATURE OF BUYER…………………………………………………………………………………….
(I am familiar with warranty conditions and the operating device is in good
working order and accessory)
DETAILS OF SELLER
NAME / COMPANY …………………………………………………………………………………………..
(be filled in by the employee)
ADDRESS ……………………………………………………………………………………………………….
(be filled in by the employee)
DATE / STAMP …………………………………………………………………………………………………
SERVICE REPORT
Receiving Protocol| Date of adoption| Description of the defect| Date of
transmission| Signature
---|---|---|---|---
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
Central Service: Bulgaria, Sofia, “Lomsko shose” 246, tel .: +359 700 44 155
DECLARATION OF CONFORMITY
R20 RAPID CHARGER 8A WITH COOLING FAN FOR SERIES RDP-R20 SYSTEM
We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
Euromaster Import Export Ltd.
Address: Sofia 1231, Bulgaria, 246 Lomsko shausse Blvd.
Product: art.№ 039713 – Rapid Charger 8A with cooling fan for series RDP-R20
System
Brand: RAIDER is designed and manufactured in conformity with following
Directives: 2014/30/EU of the European parliament and of the Council of 26
February 2014 on the harmonisation of the laws of the Member States relating
to electromagnetic compatibility 2014/35/EU of the European Parliament and of
the Council of 26 February 2014 on the harmonization of the laws of the Member
States relating to the making available on the market of electrical equipment
designed for use within cert ain voltage limits
The product fulfils the essential requirements of the following standards:
EN 60335-1:2012
EN 60335-2-29:2004/A11:2019
EN 62233:2008
EN 55014-1:2017
EN 55014-2 :2015
EN 61000-3-2:2018
EN 61000-3-3:2013
EUROMASTER IMPORT EXPORT LTD
1231, Sofia, Bulgaria, 246 Lomsko shose Blvd.,
tel.: +359 700 44 155
fax: + 359 2 934 00 90
www.euromasterbg.com; e-mail:
info@euromasterbg.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>