PreSonus Eris 3.5BT Gen 2 Bluetooth Media Reference Monitors Instruction Manual

June 16, 2024
PreSonus

Eris 3.5BT Gen 2 Bluetooth Media Reference Monitors

PreSonus-Eris-3.5BT-Gen-2-Bluetooth-Media-Reference-Monitors-
product

Product Information: Eris 3.5BT, 4.5BT, and 5BT

Specifications

  • Frequency Response:
    • Eris 3.5BT: 80Hz to 20kHz
    • Eris 4.5BT: 70Hz to 20kHz
    • Eris 5BT: 53Hz – 22kHz
  • Crossover Frequency:
    • Eris 3.5BT: 2.2kHz
    • Eris 4.5BT: 2.2kHz
    • Eris 5BT: 2.3kHz
  • Amplifier Power:
    • Eris 3.5BT: 50W
    • Eris 4.5BT: 50W
    • Eris 5BT: 100W
  • Peak SPL at 1M:
    • Eris 3.5BT: 100 dB
    • Eris 4.5BT: 100 dB
    • Eris 5BT: 110 dB
  • LF Driver Size:
    • Eris 3.5BT: 3.5″
    • Eris 4.5BT: 4.5″
    • Eris 5BT: 5.25″
  • HF Driver Size: 1 (22 mm) Silk Dome
  • Input Impedance: 10k
  • Power: 100-240V ~50/60 Hz

Product Usage Instructions

Hookup

Each pair of Eris media reference monitors consists of an active (Left) and passive (Right) cabinet, and nearly every connection is located on the active one. This speaker provides audio and power for the passive one. The exceptions are the bare-wire connectors, which send audio from the active speaker to the passive speaker.

PreSonus-Eris-3.5BT-Gen-2-Bluetooth-Media-Reference-Monitors-
fig-2

Bluetooth Pairing
  1. Turn on your Eris monitor by pressing the power button.
  2. Select the appropriate Eris model (Eris 3.5BT, Eris 4.5BT, or Eris 5BT) in your device’s Bluetooth options.
  3. Pair your device with the Eris monitor by following the on-screen instructions.
  4. You can pair an additional device by repeating steps 2 and 3. The second pairing will be stored along with the first one.
  5. Note: Audio can only be streamed from one Bluetooth device at a time.
  6. Power User Tip: The next time you switch on your Eris monitors, your stored devices will automatically be paired when powered up.

PreSonus-Eris-3.5BT-Gen-2-Bluetooth-Media-Reference-Monitors-
fig-3 PreSonus-Eris-3.5BT-
Gen-2-Bluetooth-Media-Reference-Monitors-fig-4

What’s in the Box

PreSonus-Eris-3.5BT-Gen-2-Bluetooth-Media-Reference-Monitors-
fig-1

Active Cabinet (Rear Panel)

  1. High. Boosts or cuts all frequencies above 10 kHz by ±6 dB.

  2. Low. Boosts or cuts all frequencies below 100 Hz by ±6 dB.
    Power User Tip: The Acoustic Tuning Controls work much like the treble or bass controls on a car stereo.

  3. TRS. Balanced ¼” TRS line-level inputs.

  4. IEC Power Connection. This connection accepts a standard non-polarized IEC320 C7 power cord.

  5. RCA. Unbalanced RCA line-level inputs.
    Note: While the TRS and RCA inputs offer a choice of connection type, they don’t allow simultaneous connection of multiple sources.

  6. Bluetooth Button. Pressing this button starts the pairing process. The front-panel LED will flash green while pairing and remain solid green when connected to your Bluetooth device.

  7. Bare-wire connectors (Output to Right Speaker). These send audio to the passive Eris® speaker.
    Note: Always connect the positive and negative connections on your active Eris cabinet to the corresponding connections on the passive cabinet. (i.e., connect positive-
    to-positive and negative-to-negative).

  8. Standby used to engage/disengage a power save mode that adheres to the EU Energy Efficient Products Directive to conserve energy when not in use.

  9. Volume. Sets the volume level of the input signal before it is amplified, as well as the front-panel headphone amp.

  10. Aux Input. This stereo 1/8” jack accepts audio signals from sources such as laptops, tablets, and smartphones.

  11. Headphone Output. This ⅛” stereo connection sends audio to your headphones. When headphones are connected, the speakers will not output audio.

  12. Power LED. When the speaker is switched on, the LED will light up blue to indicate that there is power, white while in standby mode, and green when paired to a Bluetooth device.

  13. Power Switch. This switches your Eris monitors on and off.

Passive Cabinet (Rear Panel)

  1. Bare-wire connectors (Input).
    These connections receive audio from the active Eris speaker.
    Note: Always connect the positive and negative connections on your active Eris cabinet to the corresponding connections on the passive cabinet. (i.e., connect positive-to-positive and negative-to-negative).

PreSonus-Eris-3.5BT-Gen-2-Bluetooth-Media-Reference-Monitors-
fig-5

Troubleshooting

No Power
Make sure your active Eris is plugged in. If it’s connected to a power strip, make sure that’s switched on and functioning properly.

No Audio
Make sure the cable connecting your audio source to the monitor is working correctly. If you’re trying to stream audio from a Bluetooth device (smartphone, tablet, etc.), make sure it’s paired to the monitors. Also, verify that the device’s volume control has been turned up.

If the passive speaker is silent, check the bare-wire connections, making sure the bare wire is fully inserted into each connector.

Hum
This is caused by a ground loop. Make sure all audio equipment is connected to a properly grounded power source.

Thin Sound
Check the bare-wire connections, and make sure the positive and negative connections on your active Eris cabinet are connected to the corresponding connectors on the passive cabinet. (i.e., positive-to-positive and negative- to-negative).

Bluetooth® Media Reference Monitors

Thank you for purchasing the PreSonus® Eris® Bluetooth® media reference monitors. Eris 3.5BT, 4.5BT, and 5BT professional near-field monitors give your home or office the sound of a studio listening environment and provide flexible connection options, professional controls, and the convenience of wirelessly streaming audio from any Bluetooth device.
This Quick Start Guide provides an overview of the Eris 3.5BT, 4.5BT, and 5BT features, Register your Eris monitor to get your manual. Visit my.presonus.com and create or log into your MyPreSonus user account to manage all your PreSonus hardware and software registrations, connect with Tech Support, and more. You can also register using the MyPreSonus app on your mobile device.

Register your serial number at My.PreSonus.com

place the serial number here

Part# 70-52000186-B

FAQ

Q: Where can I register my Eris monitor?

A: You can register your Eris monitor at My.PreSonus.com or using the MyPreSonus app on your mobile device.

Q: How can I connect the passive speaker to the active speaker?

A: The passive speaker is connected to the active speaker using the bare-wire connectors.

Q: Can I stream audio from multiple Bluetooth devices simultaneously?

A: No, audio can only be streamed from one Bluetooth device at a time.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals