TREATLIFE Wireless Scene Switch Controller with Zigbee Hub User Manual

Scene Remote
User Manual

Introduction

Treatlife Scene Remote connects to the Treatlife
App and allows you to control a group of lights across your home or trigger specific preset scenes, just press the button to light the way, even if you forget your phone.
It can be mounted almost anywhere, or it can be used as a handheld remote.

What’s in the box

Accessories included:
adhesive tape, CR2032 battery, screw, setup guide.

Getting started

To get started moke sure that you have:

1. AniOS or Android device
2. Good wifi signal
3. The Treatlife App, available on the App Store or Google Play
4.  ATreatlife Smart Hub (Sold Separately)

Quick setup

11 Scan the QR code below or search Treatlife in the App Store or Google Play to download the App, and register an account according to the instruction on the Treatiife App.

https://smartapp.tuya.com/oittm

1.2 Connect the Smart Hub to the Treatife App according to the quick guide for the hub.

1.3 Click *Add device” button on the top right, click the “Switch” on the left and select the “Scene Remote” and follow the setup guide to get it paired,

Set up actions

You con set up to 9 actions on the Treatife Smart Scene Remote, 3 for each button (single press, double press and long press).
Open the Scene Remote page, click “Add”, select one action you prefer, then assign ascene or device

Example scenes

Bedtime:
Place the Scena Remote on your badside tabie.
Before sleeping, press to tum off allyour home fihts,
Entertainment:
Proce the Scene Remote on your coffee table.
When ready to party,press to dim the ights
Guest room on/off:
Give guests contol of smort lights, from muilti locations:

Create Multi-way Control to Your Lights
Add the handheld remote to Treatlfe single pole or 3-way.
switch to control the lights from multilocations.

Wall-mounting

Thoroughly clean wallsurface. Remoue the paper from the adhesive strps on the back
of the cradle|  Attach the cradle to the wal

Snap the foceplate onto. the mounted cradle.| Amagnet in the controller holds it to the wall mount

Changing the battery

To change the battery you need to follow these steps:
Twisting the battery cover o the eft 1o opent Remove the oid battery and replace it with o new CR2032 attery with the +side up.
Place back the cover and twist to the right unt it cicks.

Note: consider that the adhesive is super strong before you stick it to any surface. Removing the adhesive might cause damage to the surface attached.

Troubleshooting

Restart
Have setup or controlissues? Remove and re-insert the battery to restart,
Restore factory settings
If the restart doesrit help, restore factory seftings.

1.  Press and hold Restore button for seconds
2. Wait until the indicator biinks, then relecse:
3. Re-add your Scene Remote to the Treatife App. and re-assign scenes to buttons

FCC Caution
This device complies with part 15 of the FCC Rules.
Operation is subject to the following twa condifions

1. This device may not cause harmful interference, and (2 this device must accept any interference received, including interforence that may cause undesired operation.
   Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   Note: This equipment has been tested and found to comply with the fimits for a Closs B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio. frequency energy and, if not nstalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there s o guarantes that interference will not ocour ina particular installation. If ths equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to ty to correct the nterference oy one or more of the following measures:
   -Rearient or relocate the receiving antenna,
   – Increase the separation batween the equipment and raceiver.
   – Connect the equipment into an outlet on a circult diferent from that 1o which the recaiver s connected.
   – Consult the dealer or an experienced radio/ TV technicion for helpThis equipment complies with FCC radiation exposure limits set forth for an uncontralled environment. This equipment should be installed and operated with minimum distance 20¢m between
   the radiator & your body.

ISEDC Warning
This device comiies with Innovation, Science, and Economic Development Canada icence-exempt RSS standardlsl. Operation s subject to the following two conditions
(1) his device may not cause interference, and
(2) this device must accept any interference, inchuding interference that may cause undesired operation of the device:
“The device s compliance with RF exposure guidelines, users an obtain Canadian information on RF exposure and complianceThe minimum distance from body to use the device is 20 cm.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>