elk HOME 89494-1 Hopkins 1 Light 30 inch Charcoal Black Outdoor Wall Sconce Instruction Manual

elk HOME 89494-1 Hopkins 1 Light 30 inch Charcoal Black Outdoor Wall

Sconce

Product Information

Specifications

• Item Number : 89494/1
• Website : elkhome.com
• Operating Hours: Monday – Friday, 8:00AM – 6:00PM ET
• Contact Number : 800-613-3261

Product Usage Instructions

1. Disconnect power at the main fuse box before installation.
2. This fixture should be installed in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, it is recommended to have the installation done by a certified electrician.
3. Before assembly, remove all parts and part packages from the box. If anything is missing, please contact the retailer from which the product was purchased.
4. Position the mounting bracket (A) so that the attached fixture mounting screws (E) are facing outward and are at the top and bottom of the mounting bracket (A).
5. Temporarily place the mounting bracket (A) over the junction box. Align the holes in the center of the mounting bracket (A) with the holes in the junction box. Mark on the wall the location of each hole in the top and bottom of the mounting bracket (A). Set aside the mounting bracket (A).
6. Using a drill bit of appropriate size, drill a hole at each marked location on the wall. Carefully insert a wall anchor (F) into each hole in the wall.
7. Position the mounting bracket (A) again so that the attached fixture mounting screws (E) are facing outward and are at the top and bottom of the mounting bracket (A).
8. Carefully pull the house wires through the hole in the center of the mounting bracket (A).
9. Align the holes in the top and bottom of the mounting bracket (A) with each wall anchor (F). Also, align the holes in the center of the mounting bracket (A) with each hole in the junction box. Ensure that the mounting bracket (A) is level.
10. Thread each wall screw (G) into the holes in the top and bottom of the mounting bracket (A) and into the wall anchors (F). Do not fully tighten the wall screws (G) at this time.
11. Thread each junction box screw (B) into the holes in the center of the mounting bracket (A) and into the holes in the junction box. Tighten both the junction box screws (B) and wall screws (G) to secure the mounting bracket (A) to the junction box. Take caution to ensure that the house wires are pulled completely through the hole in the mounting bracket and not pinched between the bracket and the wall.
12. Strip 3/4 of insulation from ends of fixture wires.
13. Slightly loosen the ground screw on the mounting bracket (A), but do not completely remove it. Wrap the house ground wire (copper) around the ground screw, leaving enough ground wire to attach to the fixture ground wire. Twist the end of the fixture ground wire and the end of the house ground wire together. Twist a wire nut (C) onto the ends of the wires and completely tighten it. Refer to the chart below for correct wire connections.
14. Twist the end of the house lead wire (black) and the end of the fixture lead wire together. Twist a wire nut (C) onto the ends of the wires and completely tighten it. Twist the end of the house neutral wire (white) and the end of the fixture neutral wire together. Twist a wire nut (C) onto the ends of the wires and completely tighten it. Refer to the chart on the right for correct wire connections.

FAQ

Q: How should I connect the supply (house) ground wire?
A: Connect the house ground wire (copper) to either a bare copper wire, bare silver wire, or green insulated wire.

WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.

WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
Before assembly, remove all parts and part packages from box. If anything is missing, please contact the retailer from which the product was purchased.

ANY QUESTIONS CALL: 800-613-3261

M-F 8:00AM-6:00PM ET

ITEM#: 89494/1

1. Position mounting bracket (A) so the attached fixture mounting screws (E) are facing outward and are at the top and bottom of the mounting bracket (A).

2. Temporarily place the mounting bracket (A) over the junction box. Align the holes in the center of mounting bracket (A) with holes in junction box. Mark on the wall the location of each hole in the top and bottom of mounting bracket (A). Place mounting bracket (A) aside.

3. Using a drill bit the appropriate size of the wall anchor (F), drill a hole at each marked location in the wall. Carefully insert wall anchor (F) into each hole in wall.

4. Position mounting bracket (A) so the attached fixture mounting screws (E) are facing outward and are at the top and bottom of the mounting bracket (A).

5. Carefully pull house wires through hole in center of mounting bracket (A).

6. Align holes in the top and bottom of mounting bracket (A) with each wall anchor (F). Align holes in center of mounting bracket (A) with each hole in junction box. Mounting bracket (A) should be level.

7. Thread each wall screw (G) into holes in top and bottom of mounting bracket (A) and into wall anchors (F). DO NOT fully tighten wall screws (G) at this time.

8. Thread each junction box screw (B) into holes in center of mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) and wall screws (G) to secure mounting bracket
   (A) to junction box. CAUTION: Make sure house wires are pulled completely through hole in mounting bracket. DO NOT pinch wires between mounting bracket and wall.

9. Strip 3/4” of insulation from ends of fixture wires.

10. Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire
    to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.

11. Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.

12. Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.

13. Carefully push all wires and wire nuts into junction box.
    Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
    ---|---
    Black Wire or,| White Wire or,
    Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
    No printed words on wire insulation or,| Printed words on wire insulation or,
    Insulated Wire (other than green) with Copper Conductor.| Insulated Wire (other than green) with Silver Conductor.

    • *When parallel wire (SPT 1 & SPT 2) is used: The lead wire is round in shape or smooth.
    • The neutral wire is square in shape or ridged.

14. Place backplate (D) over mounting bracket (A). Pass holes in backplate (D) over ends of fixture mounting screws (E). CAUTION: Do not pinch wires between backplate and wall.

15. Screw one threaded cap (F) onto end of each fixture mounting screw (E). Tighten both threaded caps (F) to secure fixture (D) to wall. DO NOT over tighten.

16. Screw recommended bulb (E26 Edison bulb type, not included) into socket. Verify correct bulb wattage marked on socket of fixture. WARNING: DO NOT exceed maximum bulb wattage.

17. Using hex wrench (R), loosen set screw on nub on backplate (D).

18. Lower ring (H) down over top of shade (K). Allow ring (H) to rest at bottom of shade (K).

19. Place roof (M) down on top of shade (K). Pass threaded pipe on inside of roof (M) through hole in top of shade (K).

20. From inside shade (K), slip silicone washer (P) then large washer (G) over threaded pipe protruding from inside top of shade (K). Thread knurled knob (L) onto end of threaded pipe. Tighten knurled knob (L) to secure shade (K) in place. DO NOT over tighten.

21. Pass hole in bottom of shade (K) down over bulb.

22. Pass holes in arm on roof (M) over threaded studs on backplate (D).

23. Pass nub on ring (H) over nub on backplate (D). Using hex wrench (R), tighten set screw on nub on backplate (D).

24. Screw one threaded cap (N) onto each threaded stud protruding from arm. Tighten threaded caps (N) to secure roof (M) in place. DO NOT over tighten.

Instructions for Mounting Fixture Outdoors or in Wet Location

Mounting surface should be clean, dry, flat and 1/4” larger than canopy on all sides. Any gaps between mounting surface and canopy exceeding 3/16” should be corrected as required.
Apply silicone caulking compound around top and sides of canopy where back of canopy meets wall surface to prevent water from seeping into junction box. Leave bottom unsealed so moisture can drain out.

MAINTENANCE NOTE

Only use a soft damp cloth to clean fixture as needed. DO NOT use harsh chemicals on fixture. Harsh chemicals may damage fixture.
Coastal conditions may cause mineral and residue build-up on fixture. It is recommended that customers in coastal areas clean all external surfaces of fixture once every two weeks with a wet cloth.

elkhome.com

References

• elkhome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>