elk HOME 32454-1 Modern Textured White Wall Sconce Lighting Installation Guide
- June 15, 2024
- elk HOME
Table of Contents
elk HOME 32454-1 Modern Textured White Wall Sconce Lighting
Instruction for use
WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.
WARNING:
This fixture is intended for installation in accordance with the National
Electrical Code (NEC) and all local code specifications. If you are not
familiar with code requirements, installation by a certified electrician is
recommended.
Before assembly, remove all parts and part packages from box. If anything is
missing, please contact the retailer from which the product was purchased.
-
Carefully pull house wires out of junction box so they are easily accessible during installation.
-
Position mounting bracket (A) up against junction box so longer end of threaded pipe (E) attached to mounting bracket (A) is pointing outward. Align each slotted hole in mounting bracket (A) with each small hole in junction box.
-
Thread one junction box screw (B) into each slot in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box. DONOT pinch wires between mounting bracket and wall.
-
Strip 3/4” of insulation from ends of fixture wires.
-
Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire together. Twist wire connector (C) onto ends of wires. Completely tighten wire connector (C). Reference chart below for correct wire connections.
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire. -
Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire connector (C) onto ends of wires. Completely tighten wire connector (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire connector (C) onto ends of wires. Completely tighten wire connector (C).
Reference chart to the right for correct wire connections. -
Wrap electrical tape (not included) around wire connectors (C) and wires. Ensure wires are securely fastened into wire connectors.
-
Carefully push all wires and wire connectors into junction box.
Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
---|---
Black Wire or,| White Wire or,
Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
No printed words on wire insulation or,| Printed words on wire insulation or,
Insulated Wire (other than green) with Copper Conductor.| Insulated Wire (other than green) with Silver Conductor.
*When parallel wire (SPT 1 & SPT 2) is used:
The lead wire is round in shape or smooth.
The neutral wire is square in shape or ridged.
-
Place backplate (D) over mounting bracket
(A). Pass hole in center of backplate (D) over end of threaded pipe (E) on mounting bracket ( A). CAUTION: Do not pinch wires between backplate and wall. -
Screw threaded cap (F) onto end of threaded pipe (E). Tighten threaded cap (F) to secure fixture to wall.
-
Lower shade down over socket.
-
Screw recommended bulb (E26 Edison bulb type, not included) into socket. Verify correct bulb wattage marked on socket of fixture. WARNING:
DO NOT exceed maximum bulb wattage.
Customer Support
https://manuals.plus/m/02ee4a335a7fe203ca0fda951d4a0e79b755ddd0275c5749ef3011d6090ac66b
ANY QUESTIONS CALL:800-613-3261
M-F 8:00AM-6:00PM ET
Documents / Resources
| elk
HOME 32454-1 Modern Textured White Wall Sconce
Lighting
[pdf] Installation Guide
32454-1, 32454-1 Modern Textured White Wall Sconce Lighting, Modern Textured
White Wall Sconce Lighting, Textured White Wall Sconce Lighting, White Wall
Sconce Lighting, Wall Sconce Lighting, Sconce Lighting, Lighting
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>