TREATLIFE DP10R Dimmer Plug and Remote Kit User Manual

: June 15, 2024
: TREATLIFE

Table of Contents

TREATLIFE DP10R Dimmer Plug and Remote Kit
PRODUCT OUTLINE
PRODUCT SPECIFICATIONS
PAIRING INSTRUCTIONS
PRODUCT FUNCTIONS
BATTERY INSTALLATION
FCC STATEMENT
More Information
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TREATLIFE DP10R Dimmer Plug and Remote Kit

PRODUCT OUTLINE

PRODUCT SPECIFICATIONS

Name: Dimmer Plug & Remote Kit
Model: DP10R
Input Voltage: 120V AC/60Hz
Max Power: 400W
Max Output: 400W INC 150W CFL 150W LED

PAIRING INSTRUCTIONS

(RF REMOTE CONTROL AND SOCKET PAIRING)

If the remote control cannot control the socket or if an additional remote control needs to be paired, please follow the steps below.

Quickly press the power button on the socket three times. The white indicator light will start flashing, indicating the RF pairing mode.
Press and hold the NO/OFF button on the remote control for about three seconds, aiming it at the flashing socket to complete the pairing process. Once successful, the white indicator light on the socket will stop flashing.

(Each socket can be paired with up to 8 remote controls.)

Minimum Brightness Setting Steps

Press and hold the NO/OFF button on the remote control for 8 seconds. The socket indicator light will start rapidly flashing in white. Use the + and – buttons on the remote control to adjust the minimum brightness of the light bulb.
Press and hold the NO/OFF button for 3 seconds again to confirm the minimum brightness setting.

PRODUCT FUNCTIONS

Socket Indicator Light

Power Status: Steady light indicates the socket is turned on, no light indicates it is turned off.
RF Pairing Mode: White flashing light.

Socket Button

Single click: Power on/off.
Long press: Adjust brightness.

Remote Control Buttons

Single click: Power on/off.
Single click/Long press +: Increase brightness.
Single click/Long press -: Decrease brightness.

BATTERY INSTALLATION

BATTERY INSTALLATION / REPLACEMENT

Common Issues

If the light is flashing, try increasing the minimum brightness (refer to the Minimum Brightness Setting Steps).
If the minimum brightness is too bright, try decreasing it (refer to the Minimum Brightness Setting Steps).
If the light doesn’t turn on after power-up, try increasing the minimum brightness (refer to the Minimum Brightness Setting Steps). If the issue persists, please check if the socket or the bulb is damaged.
If the remote control is unresponsive or not working properly, it may be due to low battery power. Please replace the CR2032 battery.

FCC STATEMENT

FCC & IC WARNING

This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IC warning

This equipment complies with IC RSS- 102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.