Haverland TAC-0923WC Portable Air Conditioner Instruction Manual

Instructions and instalation manual TAC-0923WC
TAC-1223WC

IMPORTANT SAFEGUARDS

Thank you for selecting our quality appliance. Please be sure to read this user manual carefully before using. Any question, please contact the professional service for help.
IMPORTANT
Please do not install or use your appliance before you have carefully read this manual. Please keep this instruction manual for an eventual product warranty and for future reference.
General Safety Instruction

1. The appliance is for indoor use only.

2. Do not use the unit on a socket under repairs or not installed properly.

3. Do not use the unit, follow these precautions:
   A: Near to source of fire.
   B: An area where oil is likely to splash.
   C: An area exposed to direct sunlight.
   D: An area where water is likely to splash.
   E: Near a bath, a laundry, a shower or a swimming pool.

4. Never insert your fingers, rods into the air outlet. Take special care to warn children of these dangers.

5. Keep the unit upward while transport and storage, for the compressor locates properly.

6. Before cleaning the appliance, always turn off or disconnect the power supply

7. When moving the appliance, always turn off and disconnect the power supply and move it slowly.

8. To avoid the possibility of fire disaster, the appliance shall not be covered.

9. All the appliance sockets must comply with the local electric safety requirements. If necessary, please check it for the requirements.

10. Children should be supervised to ensure that they do not play with the appliance.

11. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

12. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

13. The appliance shall be installed in accordance with national wiring regulations.

14. Details of type and rating of fuses: 250V AC, 3.15A.

15. Recycling
    This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

16. Contact authorized service technician for repair or maintenance of this unit.

17. Do not pull , deform or modify the power supply cord , or immerse it in water. Pulling or misuse of the power supply cord can result in damage to the unit and cause electrical shock.

18. Compliance with national gas regulations shall be observed.

19. Keep ventilation openings clear of obstruction.

20. Any person who is involved with working on or breaking into a refrigerant circuit should hold a current valid certificate from an industry-accredited assessment authority, which authorizes their competence to handle refrigerants safely in accordance with an industry recognized assessment specification.

21. Servicing shall only be performed as recommended by the equipment manufacturer. Maintenance and repair requiring the assistance of other skilled personnel shall be carried out under the supervision of the person competent in the use of flammable refrigerants.

22. Do not operate or stop the unit by inserting or pulling out Die power plug, it may cause electric shock or fire due to heat generation.

23. Unplug the unit if strange sounds, smell, or smoke comes from it.

NOTES:
– If any parts damage, please contact the dealer or a designated repair shop.
– In case of any damage, please turn off the air switch, disconnect the power supply, and contact the dealer or a designated repair shop.
– In any case, the power cord shall be firmly grounded.
– To avoid the possibility of danger, if power cord is damaged, please turn off the air switch and disconnect the power supply. It must be replaced from the dealer or a designated repair shop.
– If the appliance have the Wi-Fi function , the transmission power: less than 20dBm, and the radio frequency range is: 2412MHz-2472MHz.
Warning
Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
The appliance shall be stored in a room without continuously operating ignition sources (for example: open flames, an operating gas appliance or an operating electric heater.
Do not pierce or burn.
Be aware the refrigerants may not contain an odour.
Specific information regarding appliances with R290 refrigerant gas

• Thoroughly read all of the warnings.
• When defrosting and cleaning the appliance, do not use any tools other than those recommended by the manufacturing company.
• The appliance must be placed in an area without any continuously sources of ignition (for example: open flames, gas or electrical appliances in operation).
• Do not puncture and do not burn.
• This appliance contains Y g (see rating label back of unit) of R290 refrigerant gas.
• R290 is a refrigerant gas that complies with the European directives on the environment. Do not puncture any part of the refrigerant circuit.
• If the appliance is installed, operated or stored in an unventilated area, the room must be designed to prevent to the accumulation of refrigerant leaks resulting in a risk of fire or explosion due to  ignition of the refrigerant caused by electric heaters, stoves, or other sources of ignition.
• The appliance must be stored in such a way as to prevent mechanical failure.
• Individuals who operate or work on the refrigerant circuit must have the appropriate certification issued by an accredited organization that ensures competence in handling refrigerants according to a specific evaluation recognized by associations in the industry.
• Repairs must be performed based on the recommendation from the manufacturing company. Maintenance and repairs that require the assistance of other qualified personnel must be performed under the supervision of an individual specified in the use of flammable refrigerants.
• Ducts connected to an appliance shall not contain a potential ignition source.

Disposal of equipment using flammable refrigerants
See national regulations.
Storage of equipment/appliances
The storage of equipment should be in accordance with the manufacturer’s instructions.
Storage of packed (unsold) equipment
Storage package protection should be constructed such that mechanical damage to the equipment inside the package will not cause a leak of the refrigerant charge.
The maximum number of pieces of equipment permitted to be stored together will be determined by local regulations.

• Disconnect the appliance from its power source during service and when replacing parts and cleaning.
• Please note: Check the nameplate for the type of refrigerant gas used in your appliance.
• Specific information regarding appliances with refrigerant gas. The appliance is recommended not to pierce the cooling circuit of the machine. At the end of its useful life, deliver the appliance to a special waste collection centre for disposal. GWP(Global Warming Potential): R410A: 2088, R134a: 1430, R290: 3, R32: 675.
• Do not use this unit for functions other than those described in this instruction manual.
• Make sure the plug is plugged firmly and completely into the outlet. It can result in the risk of electric shock or fire.
• Do not plug other appliances into the same outlet, it can result in the risk of electric shock.
• Do not disassemble or modify the appliance or the power cord, it can result in the risk of electric shock or fire. All other services should be referred to a qualified technician.
• Do not place the power cord or appliance near a heater, radiator, or other heat source. It can result in the risk of electric shock or fire.
• This unit is equipped with a cord that has a earthed wire connected to an earthed pin or grounding tab. The plug must be plugged into a socket that is properly installed and earthed. Do not under any circumstances cut or remove the earthed pin or grounding tab from this plug.
• The unit should be used or store in such a way that it is protected from moisture e.g. condensation, splashed water, etc. Unplug unit immediately if this occurs.
• Always transport your appliance in a vertical position and place on a stable, level surface during use. If the unit is transported laying on its side it should be stood up and left unplugged for 6 hours.
• Always use the switch on the control panel or remote controller to turn the unit off, and do not start or stop operation by plugging in or unplugging the power cord. It can result in the risk of electric shock.
• Do not touch the buttons on the control panel with your wet and damp fingers.
• Do not use hazardous chemicals to clean or come into contact with the unit. To prevent damage to the surface finish, use only a soft cloth to clean the appliance. Do not use wax, thinner, or a strong detergent. Do not use the unit in the presence of inflammable substance or vapour such as alcohol, insecticides, gasoline, etc.
• If the appliance is making unusual sounds or is emitting smoke or an unusual odor, unplug it immediately.
• Do not clean the unit with water. Water can enter the unit and damage the insulation, creating a shock hazard. If water enters the unit, unplug it immediately and contact Customer Service.
• Utilize two or more people to lift and install the unit.
• Always grasp the plug when plugging in or unplugging the appliance. Never unplug by pulling on the cord. It can result in the risk of electrical shock and damage.
• Install the appliance on a sturdy, level floor capable of supporting up to 110lbs(50kg). Installation on a weak or unlevel floor can result in the risk of property damage and personal injury.
• The appliance is compliant with the RE Directive (2014/53/EU).

According the UK standard
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.
• The appliance shall be installed in accordance with national wiring regulations.
• When the fuse is blown/circuit breaker is tripped, check the house fuse/circuit breaker box and replace fuse or reset breaker.

ELECTRICAL CONNECTIONS
Before plugging the appliance into the mains socket, check that:

• The mains power supply corresponds to the value indicated on the rating plate on the back of the appliance.
• The power socket and electrical circuit are adequate for the appliance.
• The mains socket matches the plug. If this is not the case, have the plug replaced.
• The mains socket is adequately earthed. Failure to follow these important safety instructions absolves the manufacturer of all liability.

INSTALLATION

Exhaust hose
Hose outlet| 1 SET
| Window slider kit| 1 SET
| Remote control
Battery| 1 SET

Note: All the illustrations in this manual are for explanatory purposes only. Your appliance may be slightly different.
Be sure all accessories are removed from the packing before use.

INSTALLATION INSTRUCTIONS

• The unit should be placed on a firm foundation to minimize noise and vibration. For safe and secure positioning place the unit on a smooth, level floor strong enough to support the unit.
• The unit has casters to aid placement, but it should only be rolled on smooth, flat surfaces. Use caution when rolling on carpeted surfaces. Use caution and protect floors when rolling over wood floors. Do not attempt to roll the unit over objects.
• The unit must be placed within reach of a properly rated grounded socket.
• Never place any obstacles around the air inlet or outlet of the unit.
• Allow at least 18”(45cm) of around and above space away from the wall for efficient working.
• The hose can be extended, but it is the best to keep the length to minimum required. Also make sure that the hose does not have any sharp bends or sags.

Note: In TAC0923WC model, before install the exhaust hose, follow the fig remove hose outlet first.

1. Press the hook.
2. Remove the hose outlet upwards.

When use the appliance in cool mode, the hot air exchange of the condenser must be exhausted out of the room completely. First position unit on a flat floor and make sure there’s a minimum of 18”(45cm) clearance around the unit, and is within the vicinity of a single circuit outlet power source.

1. Extend either side of the hose (Fig. 1), and screw the hose inlet (Fig. 2).
2. Extend the other side of the hose and screw it to the hose outlet (Fig. 3).
3. Install the hose inlet into the unit (Fig. 4).
4. Affix the hose outlet into the window slider kit and seal. (Fig. 5 & 6).

The window slider kit has been designed to fit most standard vertical and horizontal window applications,however, it may be necessary for you to modify some aspects of the installation procedures for certain types of windows. The window slider kit can be fastened with screws.
NOTE: If the window opening is less than the minimum length of the window slider kit, cut the end without the hold in it short enough to fit in the window opening. Never cut out the hole in window slider kit.

WINDOW SLIDER KIT INSTALLATION

1. Parts:
   A) Panel
   B) Panel with one hole
   C) Screw to lock window kit in place

2. Assembly: Slide Panel B into Panel A and size to widow width. Windows sizes vary. With the width that your window requires to ensure that there are no gaps or air pockets in the window kit assembly after installation.

3. Lock the screw into the hole that correspond.

OPERATION

DESCRIPTION OF THE DISPLAY SCREEN AND CONTROL PANEL

1. Timer button
2. Fan button
3. Decrease button
4. Display screen
5. Increase button
6. Mode button
7. ON/OFF button

A. Mode symbol
B. Fan speed symbol
C. Sleep symbol
D. Timer symbol
E. WiFi symbol
When the unit is connected with phone, the WiFi symbol is light on.
3.1 TURNING THE APPLIANCE ON/OFF
– Plug into the mains socket, then the appliance is standby.
– Press the button to make the appliance turn on. The last function active when it was turned off will appear.
√ Never turn the air conditioner off by unplugging from the mains. Always press the button , then wait for a few minutes before unplugging. This allows the appliance to perform a cycle of checks to verify operation.
3.2 COOL MODE
Ideal for hot muggy weather when you need to cooling and dehumidify the room.
To set this mode correctly:
—Press the “ “ button a number of times until the “Cool” symbol light appears.
—Select the target temperature18℃-32℃(64℉-90℉) by pressing the “ “ ” “ button until the corresponding value is displayed.
— Select the required fan speed by pressing the . button. Three speeds are available: High / Low / Auto.
The most suitable temperature for the room during the summer varies from 24℃ to 27℃. You are recommended, however, not to set a temperature much below the outdoor temperature. This will cause unnecessary power consumption.
3.3 FAN MODE
When using the appliance in this mode, the air hose does not need to be attached.
To set this mode correctly:
—Press the “ ” button a number of times until the “Fan” symbol appears.
—Select the required fan speed by pressing the button.
Two speeds are available: High / Low.
The screen display “ ” as high speed, “ ” as low speed.
3.4 DRY MODE
Before using the dry mode, the appliance should be prepared in the same way as for cool mode, with the air exhaust hose attached to enable the moisture to be discharged outside.
To set this mode correctly:
– Press the varias veces hasta que button a number of times until the “Dry”symbol light appears, the screen will appear ” ”.
– In this mode, fan speed is selected automatically by the appliance.
3.5 SETTING THE TIMER
This timer can be used to delay the appliance start up or shutdown, this avoids wasting electricity by optimizing operating periods.
* Programming start-up*
– Turn on the appliance, choose the mode you want, for example Dehumidify mode, high fan speed.
Turn off the appliance.
– Press the “ “, button, the screen starts to flash, press the “ “ “ “ to adjust the set time from 0.5-24 hours.
– In 5 seconds without the operation, the timer start function, then the “Timer” symbol lights.
– Press the “ “ button again to cancel the Timer, and the “Timer” symbol disappear.
Programming shut down**
– When the appliance is running, press the “  button, the screen starts to flash.
– Press the “ “ “ “ to adjust the set time from 0.5-24 hours.
– In 5 seconds without the operation, the timer start function, then the “ Timer” symbol lights.
– Press the “ “ “ button again to cancel the Timer, and the “ Timer “ symbol disappear.
* Switch the unit of temperature
When the appliance is running, hold on “ ” and “ “ button together 3 seconds by the same time, then you can change the unit of temperature.
For example:
Before change, in cool mode, the screen display like fig 1 (ºC). After change, in cool mode, the screen display like fig 2 (ºF).

3.6 SMART MODE
The appliance chooses automatically whether to operate in cool or fan mode.
To set this mode correctly:

• Press the button a number of times until the screen show like below:
• Select the required fan speed by pressing the button.

Three speeds are available:High / Low / Auto.
If the appliance is cooling only model, the unit operates in Fan mode when the room temperature is below 23℃ (73℉), and Cool mode when the room temperature is above 23℃(73℉).
3.7 SELF-DIAGNOSIS
The appliance has a self diagnosis system to identify a number of malfunctions.
Error messages are displayed on the appliance display.

authorize service centre.
FULL TANK (safety tank full)| Empty the internal safety tank, following the instructions in the “End of season operations”
paragraph.

3.8 REMOTE CONTROL
√ Point the remote control at the receiver on the appliance.
√ The remote control must be no more than 7 meters away from the appliance (without obstacles between the remote control and the receiver).
√ The remote control must be handled with extreme care. Do not drop it or expose it to direct  sunlight or sources of heat. If the remote control do not work, please try to take out the battery, and put it back again.
3.9 SWING FUNCTION (ONLY REMOTE CONTROL) This function moves the deflector to adjust the direction of the air flow.
To set this function correctly:

• Press the button to select the horizontal deflector to automatically move up and down.
• Press the button again to switch off this function.

3.10 SLEEP FUNCTION (ONLY REMOTE CONTROL)
This function is useful for the night as it gradually reduces operation of the appliance.
To set this function correctly: Select the cool mode as described above.
Press the “. button.

• The appliance operates in the previously selected mode.
• When you choose the sleep function, the screen will reduce the brightness and the fan speed is low.
• The SLEEP function maintains the room at optimum temperature without excessive fluctuations in either temperature or humidity with silent operation. Fan speed is always at Low, while room temperature and humidity vary gradually to ensure the most comfortable.
• When in COOL mode, the selected temperature will increase by 1℃(1℉) per hour in a 2 hour period. This new temperature will be maintained for the next 6 hours. Then the appliance turn it off.
• The SLEEP function can be canceled at any time during operation by pressing the “Sleep”, “Mode” or “fan speed” button.
• In DRY and SMART modes, SLEEP function is still available.

3.11 INSERTING OR REPLACING THE BATTERIES

• Remove the cover on the rear of the remote control;
• Insert two “AAA” 1.5V batteries in the correct position (see instructions inside the battery compartment
  NOTE:
  √ If the remote control unit is replaced or disposed of, the batteries must be removed and discarded in accordance with current legislation as they are harmful to the environment.
  √ Do not mix old and new batteries. Do not mix alkaline, standard (carbon- zinc) or rechargeable (nickel-cadmium) batteries.
  √ Do not dispose of batteries in fire. Batteries may explode or leak.
  √ If the remote control is not be used for a certain length of time, remove the batteries.

3.12 TIPS FOR CORRECT USE
To get the best from your appliance, follow these recommendations:

• Close the windows and doors in the room to be air conditioned (fig. 21).When installing the appliance semi-permanently, you should leave a door slightly open (as little as 1 cm) to guarantee correct ventilation;
• Protect the room from direct exposure to the sun by partially closing curtains and/or blinds to make the appliance much more economical to run (fig. 22);
• Never rest objects of any kind on the appliance;
• Do not block the air inlet or outlet of the appliance. Reduced air flow will result in poor performance and could damage the unit (fig. 23).
• Make sure there are no heat sources in the room;
• Never use the appliance in very damp rooms (laundries for example).
• Never use the appliance outdoors.
• Make sure the appliance is standing on a level surface. If necessary, place the castor locks under the front wheels.

3.13 WATER DRAINAGE METHOD
When there is excess water condensation inside the unit, the appliance stops running and shows
FL (FULL TANK as mentioned in SELF-DIAGNOSE). This indicates that the water condensation needs to be drained using the following procedures:
Manual Draining (fig.24)

1. Unplug the unit from power source.
2. Place a pan (not supply) under the lower drain plug. See diagram.
3. Remove the lower drain plug.
4. Water will drain out and collect in the pan.
5. After the water is drained, replace the lower drain plug firmly.
6. Turn on the unit.

Continuous Draining (fig.25)

1. Unplug the unit from the power source.
2. Remove the drain plug. While doing this operation some residual water may spill so please have a pan not supply) to collect the water.
3. Connect the drain hose (1/2” or 12.7mm, not supply ). See diagram.
4. The water can be continuously drained through the hose into a floor drain or bucket.
5. Turn on the unit.

NOTE
Please be sure that the height of and section of the drain hose should not be higher than that of the drain outlet, or the water tank may not be drained. (fig. 26 and fig. 27)

Middle drainage
When unit running in Dry mode, you can choose the way below to drainage:

1. Unplug the unit from the electrical outlet.
2. Remove the drain plug (fig. A). During this operation, residual water may spill out, so a container must be provided to collect the water.
3. Connect the drain hose (1/2” or 12.7mm, may not be supplied). (fig B)
4. Water can be continuously discharged through the hose to a floor drain or bucket.
5. Turn on the device.

3.14 CLEANING
Before cleaning or maintenance, turn the appliance off by pressing the button on the control panel or remote control, wait for a few minutes then unplug from the mains socket.
Cleaning the cabinet
You should clean the appliance with a slightly damp cloth then dry with a dry cloth, may not used water to wash appliance.

• Never wash the appliance with water. It could be dangerous.
• Never use petrol, alcohol or solvents to clean the appliance.
• Never spray insecticide liquids or similar.

Cleaning the air filters
To keep your appliance working efficiently, you should clean the filter every month ofoperation.
The evaporator filter can take out like fig.

• To avoid possible cuts, avoid contacting the metal parts of the appliance when removing or reinstalling the filter. It can result in the risk of personal injury.
  Use a vacuum cleaner to remove dust accumulations from the filter. If it is very dirty, immerse in warm water and rinse a number of times. The water should never be hotter than 40℃(104℉). After washing, leave the filter to dry then attach the intake grille to the appliance.

3.15 END OF SEASON OPERATIONS
To empty the internal circuit completely of water, remove the cap(fig. below).
Run off all water left into a basin. When all the water has been drained, put the cap back in place.
Clean the filter and dry thoroughly before putting back.

3.16 TROUBLESHOOTING

PROBLEM| CAUSE|

SOLUTION

---|---|---
The appliance does not come on| •There is no current
•It is not plugged into the mains
•The internal safety device has tripped| •Wait
•Plug into the mains
•Wait 30 minutes, if the problem persists, contact your service center
The appliance works for a short time only| •Here are bends in the air exhaust hose
•Something is preventing the air from being discharged| •Position the air exhaust hose correctly, keeping it as short and free of curves as possible to avoid bottlenecks
•Check and remove any obstacles obstructing air discharge
The appliance works, but does not cool the room| •Windows, doors and/or curtains open| •Close doors, windows and curtains, bearing in mind the “tips for correct use” given above.
•There are heat sources in the room (oven, hairdryer, etc)| •Eliminate the heat sources
•The air exhaust hose is detached from the appliance| •Fit the air exhaust hose in the housing at the back of the appliance.
•The technical specification of the appliance is not adequate for the room in which it is located| •Ask to your distribuitor.
During operation, there is an unpleasant smell in the room| •Air filter clogged.| •Clean the filter as described above
The appliance does not operate for about three minutes after restarting it.| •The internal compressor safety device prevents the appliance from being restarted until three minutes have elapsed since it was last turned off.| •Wait. This delay is part of normal operation
The following message the display:

| •The appliance has a self diagnosis system to identify a number of malfunctions| •See the SELF-DIAGNOSIS Chapter

3.17 WIFI CONFIGURATION
Minimum specifications on a Smart phone:
Android 5.0 version or higher / IOS 10.0 version or higher
Network frequency: 2,4 GHz
Steps:

1. Download and Install the App “SmartLife-SmartHome”: Note: Please enable the permissions of Storage / Location / Camera / Wi-Fi / Bluetooth for this APP when installing. Otherwise it will have some problems when operating.

2. When you first time enter the APP, it will display activation interface, you can select activation QR code(click “Scan” button and scan the activation QR code in below page) or input “Activation code” words (in below page), click “Activate” button to active it.

3. Registration Note: Set the Password with 6-20 characters including characters and numbers.

4. Add device:
   4.1 Please power on the appliance, but do not press the  button to turn on it. The screen show:
   4.2 Hold the “ ” **“ ” button about 5 seconds to switch on the Wi-Fi function.
   The display screen will show the “CF”.**
   4.3 Click “ +“ in the upper right corner of the “Home” screen or tap “Add device”: 4.4 Tap the “Portable Air Conditioner” logo

5. Input the password of the Wi-Fi which the same as your smart phone connected, then tap “Next”. Please make sure the “Password” is correct, or the connect will be failure.

6. Click “ ”in the upper right corner and select the “CF Mode”, and tap “Next”.

7. “CF” mode: Follow the steps.7.1) You can see the percent rate of connecting process:
   “PP” means “Searching the router”
   “SA” means “connected to the router”
   “AP” means “connected to the server” Note: If connect Wi-Fi failure, please try to reset WIFI module and connect it again.
   7.2) There are three methods to reset the WIFI module:
   A) Press the ” button on the control panel 6 times within 4 seconds. Every time reset the Wi-Fi, must wait about 10 seconds, then the screen will display “CF” or “AP” 5 times.
   B) Hold the button on the control panel about 5 seconds.
   C) Hold the button on the control panel about 3 seconds.

8. AP mode: Follow the steps:8.1) You can see the percent rate of connecting process, at the same time “PP”, “SA”, “AP” shining in turn on the appliances display. “PP” means “Searching the router” / “SA” means “connected to the router” / “AP” means “connected to the server” Note: If connect Wi-Fi failure, please try to reset WIFI module and connect it again.

Paring Process
CF: Waiting pair after reset
AP: 1) Hot-spot connect mode
2) Access to the Internet PP: Searching and try to connect
SA: Connect successful

3.16 TROUBLESHOOTING

Storage / Location / Camera / Wi-Fi / Bluetooth for this APP when installing. Otherwise it will have some problems when operating.
•Check the mobile connected WLAN router SSID and password is correct:
•Check whether there are additional settings of WLAN router as shown below.

1. Firewall by router itself or by PC 2) MAC address filtering 3) Hidden SSID
2. DHCP server
   Reboot WLAN router. mobile device and appliance (WLAN module) and connect appliance by CF or AP mode again. Before rebooting, check nobody has already connected to same appliance.
   Mobile can’t control appliance| •When appliance (WLAN module) is rebooted and app displays device remove. ignoring this confirmation will lead to mobile device losing control permission of the appliance. You will need to connect the appliance by CF or AP mode again.
   •In case of power failure, mobile device will lose control permission of appliance for 3 minutes after power failure. (Notification will now show up on the mobile device.)
   If you cannot control the app (appliance) even after power restored, you will need to connect the appliance by CF or AP mode again.
   Mobile can’t find appliance| •App display appliance Device offline. Please check the following conditions.
   1)The appliance has been reconfigured.
   2)Appliance out of power.
   3)Router out of power.
   4)Appliance can’t connect to router.
   5)Appliance can’t connect to network through the router.
   6)Mobile device can’t connect to network.
   •After adding the device, it disappears in device list .
   Hold and slide down to refresh the device list. If it has no change. shut down the app and start again.

GUARANTEE

MARSAN INDUSTRIAL, S.A. guarantees that the devices comply with the contracted specifications.
This warranty only covers the model of heater showed on the valid invoice.
Such rectifications will be guaranteed against any manufacturing and operating defect for the normal and domestic use of this product, for a period of 24 months as from the purchase date shown on the invoice.
HAVERLAND guarantees against material, design or manufacturing faults at the moment of its original acquisition for 2 years.
This warranty DOES NOT COVER incorrect installation, maintenance, cleaning or conserving the device, and neither does it cover failures and faults due to force major, chemical agents or atmospheric phenomena, incorrect use of the device, the purchaser’s faulty electrical installations, transporting the device or problems caused by the device being handled by persons not authorised by MARSAN
INDUSTRIAL, S.A.
This warranty must not be modified, altered or extended, and the Manufacturer does not authorise anybody to act on his behalf to modify, alter or extend it.
This warranty applies only to the Product.
To repair the device, the consumer must dial the Technical Assistance Service at 0330 3651940 or send an email to haverland@haverland.co.uk and ask for the information needed about the procedure to follow:
For a replacement, cancellation or price reduction, when in order, the consumer must go the establishment where the device was purchased. This warranty does not affect the consumers’ rights as established in the provisions contained In Law 23/2003, the Consumer Goods Sales Guarantee Act.
Customer Service Telephone: 0330 3651940
E-mail: haverland@haverland.co.uk
Where you see this symbol on any of our electrical products or packaging, it indicates that the relevant electrical product should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product, please dispose of it in accordance with any applicable local laws or requirements for disposal of electrical equipment. In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste.

Haverland UK Limited
Chattengue House
Sherwood Drive
Bletchley MK3 6DP
Marsan Industrial, S.A. reserves the right to modify without previous warning
Made in PRC

Documents / Resources

| Haverland TAC-0923WC Portable Air Conditioner [pdf] Instruction Manual
TAC-0923WC, TAC-1223WC, TAC-0923WC Portable Air Conditioner, Portable Air Conditioner, Air Conditioner, Conditioner
---|---

References

• Your Electric Radiator Specialists | Haverland | UK
• Expertos en radiadores eléctricos y emisores térmicos - Haverland

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>