JBC Stand for AT420 Adjustable Thermal Tweezers Instruction Manual

JBC Stand for AT420 Adjustable Thermal Tweezers

This manual corresponds to the following references: AT-SB

Packing List

The following items are included

Features and Connections

Assembly

Wiper
The integrated wiper offers different ways to clean the cartridge tips.

• Tap gently to remove excess solder.
• Use the slots to remove the remaining particles.
• The softest cleaning method. Keep the sponge damp with distilled water when working to avoid tip wear

Wiper and Brass Wool Replacement.

The wiper and brass wool can easily be removed for cleaning or replacement when they are worn.

• Lift the wiper at its front edge.
• Remove the wiper by pulling it out.
• Replace the brass wool with a new one when it is worn out.

Changing Cartridges

1. Unlocking
   Unlock the fixing screws.
   

2. Removing
   Place the cartridges in the extractor (1) and pull the tweezers to remove them (2).

3. Positioning
   Use the vertical grooves to position the cartridges and place the tweezers onto the cartridges.

4. Inserting
   Press the cartridges against the extractor and make sure that the cartridge is inserted up to the mark*
   Important
   It is essential to insert the cartridges as far as the mark for a proper connection.
   

5. Rotational Cartridge Alignment and Locking
   Slightly turn the wheels to align the cartridges as required (1). Then lock the cartridge fixing screws* (2).

6. Vertical Cartridge Alignment
   Once the alignment has been made, it is imperative to fix the cartridges by tightening the fixin screws. It takes a single turn of the screw to lock it in place.
   

Once the alignment has been made, it is imperative to fix the cartridges by tightening the fixin screws. It takes a single turn of the screw to lock it in place.

Tweezers Positioning

The tweezers position in the the image (1).

Note

When using the customized cartridges like ref. C420283 and ref. C420286, place the tweezers vertically, as shown in the image (2).

Accessories

Maintenance

Before carrying out maintenance or storage always unplug the stand from the station and the tool.

• Use a damp cloth to clean the stand. Alcohol can be used only when cleaning metal parts.
• Check periodically that the metal parts of the tool/stand are clean so that the station can check the tool’s status.
• Periodically check all cables and tube conections.
• Replace any defective or damaged parts. Use original JBC spare parts only.
• Repairs should only be performed by a J B C authorized technical service.

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

• – Do not use the units for any purpose other than soldering or rework. Incorrect use may cause a fire.
• The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire.
• Do not work on electrically live parts.
• The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when
• adjusting the stand position.
• Do not leave the appliance unattended when it is on.
• Do not cover the ventilation grills. Heat can cause inflammable products to ignite.
• Avoid the contact of flux with skin or eyes to prevent irritation.
• careful with the fumes produced when soldering.
• Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
• Utmost care must be taken with liquid tin waste which can cause burns.
• This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance.
• Maintenance must not be carried out by children unless supervised.

Specifications

• ATS
• Stand for AT420 Adjustable Thermal Tweezers
• Ref.: AT-SB
•  Includes Sleep Mode and Hibernation Mode
• Net Weight 1544 g / 3.40 lb
• Package Dimensions / Weight 342 x 155 x 120 mm / 2106 g
• (L x W x H) 13.5 x 6.1 x 4.7 in / 4.64 lb
• Complies with CE standards
• ESD Safe

Warranty

JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.

This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

www.jbctools.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>