Lowe s A05090 Erharting 5-Light Brushed Glass Cylinder Hanging Kitchen Island Light Instruction Manual

Lowe s A05090 Erharting 5-Light Brushed Glass Cylinder Hanging Kitchen Island Light Instruction Manual

INSTRUCTION

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5.  Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

• Ladder

• Philips Head or Flat Blade Screwdriver

• Electrical Tape

• Pliers
  

• Wire Cutter/Stripper
  

PARTS TYPE & QTY INCLUDED

• (C) Mounting plate(1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Loop (4)
• (G) Quick link (4)
• (H) Ball nut (2)
• (I) Chain (2)
• (J) Tube (2)
• (K) Frame (1)
• (L) Socket (5)
• (M) Lampshade (5)

ACCESSORIES & QTY ENCLOSED

• (A) Wire connector (3)
• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Make pre-installation

• Step A1 By measuring, determine the correct number of links needed for proper hanging height. Using the
  chain pliers, disconnect and discard the unwanted part.

• Step A2
  

  • Screw tubes (J) onto frame (K).
  • Open quick links (G) in the chains (I). Attach quick links (G) to loops (F) on canopy and on the
    top of tubes (J)

• Step A3
  Carefully pass the fixture wires through one of chain (I).

Turn off power

Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

• Go to the main fuse, or circuit breaker, box in your home.
  Place the main power switch in the “OFF” position.

• Place the wall switch in the “OFF” position.

Make installation

• Step B1 » Unscrew ball nuts (H) from mounting plate (C)
  

• Step B2 » Attach mounting plate (C) to the outlet box with mounting screws (B).
  
  Note: the side of mounting plate (C) marked “GND” must face out.

• Step B3 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured
  above mounting plate (C) is at least 6″.
  

• Step B4 » Make wire connections
  
  Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the chart below

Connect wires according to the chart below

tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor

• Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

• Twist wires together with plastic wire connectors until tightly joined.

• Wrap each connector with approved electrical tape and sure that no wire strands are exposed.

• Carefully tuck all wires into the outlet box.

Step B5 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening ball nuts (H) onto preassembled screws on mounting plate (C).

NOTE: canopy (E) should be snug against the ceiling with ball nuts (H). If not, remove canopy (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (C):

• First, unscrew the pre-assembled hex nuts.
• Then, screw the pre-assembled mounting screws in or out of mounting plate (C).
• When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step B5.

Step B6

1. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
2. Carefully screw lampshades (M) onto sockets (L) as shown in the illustration.
   

Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lightin

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>