Lowe s A05240 Jessaes 12-Light Polished Gold Large Candle Modern/Contemporary LED Instruction Manual

Lowe s A05240 Jessaes 12-Light Polished Gold Large Candle

Modern/Contemporary LED

Product Information

Specifications:

• Item Number: A05240
• Maximum Voltage: 120V
• Maximum Wattage: Type B, Max 40W per bulb

Product Usage Instructions:

Installation:

• To reduce the risk of fire, electric shock, or personal injury, we recommend installation by a licensed electrician.
• Before starting the installation process, make sure to read the instructions carefully and save them for future reference. Also, ensure that the electricity is shut off before attempting any work.
• The mounting surface should be clean, dry, flat, and strong enough to support the fixture. It should also be 1/4 larger than the canopy on all sides. If there are any gaps between the mounting surface and canopy exceeding 3/16, they should be corrected as required.
• Check if the ceiling or wall can withstand the weight of the lamp before installation.

Voltage and Bulb:
Make sure that the voltage you are using is 120V. The maximum wattage allowed is Type B, with a maximum of 40W per bulb.

Lamp Maintenance:

• Keep the lamp away from acidic and alkaline substances to prevent damage to the lamp’s surface.
• When replacing bulbs, turn off or unplug the lamp and wait until it cools down as bulbs can get hot quickly.

Safety Instructions:
Please note that the safety instructions provided in this manual may not cover all possible conditions. It is essential to use common sense, caution, and care when dealing with any electrical products.

Ordering Parts:
Keep the provided sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. When ordering parts, use the exact wording from the provided illustration.

Cleaning:
To clean the fixture, wipe it with a soft cloth. For cleaning the glass, use a mild cleaner such as mild and non-abrasive soap. Avoid using abrasive materials like scouring pads, powders, steel wool, or abrasive paper.

Tools Required:
Before starting assembly and installation, make sure to have the following tools ready:

• Ladder
• Philips Head or Flat Blade Screwdriver
• Electrical Tape
• Pliers
• Wire Cutter/Stripper

FAQ:

• Q: Can I install the fixture by myself?
  A: While it is possible to install the fixture yourself, we recommend installation by a licensed electrician to ensure safety and proper installation.

• Q: What should I do if there are gaps between the mounting surface and the canopy?
  A: Any gaps exceeding 3/16 should be corrected to ensure proper installation. You can use suitable materials to fill in the gaps as required.

• Q: Can I use bulbs with a wattage higher than 40W per bulb?
  A: No, the maximum wattage allowed per bulb is 40W. Using higher-wattage bulbs can lead to potential hazards.

• Q: How should I clean the glass of the fixture?
  A: To clean the glass, use a mild cleaner such as mild and non-abrasive soap. Avoid using abrasive materials like scouring pads, powders, steel wool, or abrasive paper.

Warning Instruction

WARNING
(To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per blub.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

TOOLS REQUIRED

(NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDED

• (C) Single bar (1)

• (D) Green ground screw (1)

• (E) Canopy (1)

• (F) Collar ring (1)

• (G) Collar loop (1)

• (H) Quick link (2)

• (I) Chain (1)

• (J) Loop (1)

• (K) Thread rod (1)

• (L) Decorative column (1)

• (M) Hex nut (1)

• (N) Gasket (1)

• (O) Arms assembly (1)

• (P) Arm (6)
  ACCESSORIES & QTY ENCLOSED:

• (A) Wire connector (3)

• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Make pre-installation

   • Step A1 » Screw thread rod (K), hex nut (M), and gasket (N) onto the top of arms assembly (O) as shown in the illustration.
     Step A2» Screw decorative column (L) onto the top of arms assembly (O), and then screw loop (J) onto the top of the decorative column (L) as shown in the illustration.

   • Step A3» Ajust arms (P) to proper position as shown in the illustration.

   • Step B1 » By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.

   • Step B2 » Attach quick links (H) to chain (I) and loop (J) on the top of thread rod (L).

   • Step B3 » Carefully weave the fixture wires through main chain (I) in and out of every other link and stop just when you reach the top of chain (I). Gently pull the wires to ensure the wires are not stressed.

3. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

4. Make installation

   • Step C1 » Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B).
     NOTE: the side of the single bar (C) marked “GND” must face out.

   • Step C2 » Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position. Unscrew collar ring (F) from collar loop (G) and remove canopy (E). Refer to the following note, you would know the proper position where the collar loop (G) should be located.
     NOTE: canopy (E) should be snug against the ceiling and collar loop (G) should be screwed with enough threads (no less than 6 threads) on the pre- assembled threaded nipple for more secure hanging.

   • If not, adjust the collar loop (G) on the single bar (C) by screwing the collar loop (G) in or out of the single bar (C) until the secure length is achieved.

   • Step C3 » Pass chain (I) through collar ring (F) and then through canopy (E).

   • Step C4 » Open quick link (H), attach quick link (H) to collar loop (G). Close quick link (H). Pass the fixture wires through the collar loop (G) to the top of the pre-assembled threaded nipple and gently pull to ensure the wires are not stressed.

   • Step C5 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above the single bar (C) is at least 6″.

   • Step C6 » Make wire connections
     Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

   • Twist wires together with plastic wire connectors (A) until tightly joined.

   • Wrap each connector with approved electrical tape.

   • Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

   • Step C7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).

   • Step C8 » Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

5. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>